linux-toradex.git/include/linux/spi, branch v2.6.31.7

spi: add spi_master flag word

2009-07-01T01:56:00+00:00

Add a new spi_master.flags word listing constraints relevant to that
controller.  Define the first constraint bit: a half duplex restriction.
Include that constraint in the OMAP1 MicroWire controller driver.

Have the mmc_spi host be the first customer of this flag.  Its coding
relies heavily on full duplex transfers, so it must fail when the
underlying controller driver won't perform them.

(The spi_write_then_read routine could use it too: use the
temporarily-withdrawn full-duplex speedup unless this flag is set, in
which case the existing code applies.  Similarly, any spi_master
implementing only SPI_3WIRE should set the flag.)

Signed-off-by: David Brownell 
Cc: Marek Szyprowski 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds

spi: new spi->mode bits

2009-07-01T01:56:00+00:00

Add two new spi_device.mode bits to accomodate more protocol options, and
pass them through to usermode drivers:

 * SPI_NO_CS ... a second 3-wire variant, where the chipselect
   line is removed instead of a data line; transfers are still
   full duplex.

   This obviously has STRONG protocol implications since the
   chipselect transitions can't be used to synchronize state
   transitions with the SPI master.

 * SPI_READY ... defines open drain signal that's pulled low
   to pause the clock.  This defines a 5-wire variant (normal
   4-wire SPI plus READY) and two 4-wire variants (READY plus
   each of the 3-wire flavors).

   Such hardware flow control can be a big win.  There are ADC
   converters and flash chips that expose READY signals, but not
   many host controllers support it today.

The spi_bitbang code should be changed to use SPI_NO_CS instead of its
current nonportable hack.  That's a mode most hardware can easily support
(unlike SPI_READY).

Signed-off-by: David Brownell 
Cc: "Paulraj, Sandeep" 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input

2009-06-20T17:17:02+00:00

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (35 commits)
  Input: add driver for Synaptics I2C touchpad
  Input: synaptics - add support for reporting x/y resolution
  Input: ALPS - handle touchpoints buttons correctly
  Input: gpio-keys - change timer to workqueue
  Input: ads7846 - pin change interrupt support
  Input: add support for touchscreen on W90P910 ARM platform
  Input: appletouch - improve finger detection
  Input: wacom - clear Intuos4 wheel data when finger leaves proximity
  Input: ucb1400 - move static function from header into core
  Input: add driver for EETI touchpanels
  Input: ads7846 - more detailed model name in sysfs
  Input: ads7846 - support swapping x and y axes
  Input: ati_remote2 - use non-atomic bitops
  Input: introduce lm8323 keypad driver
  Input: psmouse - ESD workaround fix for OLPC XO touchpad
  Input: tsc2007 - make sure platform provides get_pendown_state()
  Input: uinput - flush all pending ff effects before destroying device
  Input: simplify name handling for certain input handles
  Input: serio - do not use deprecated dev.power.power_state
  Input: wacom - add support for Intuos4 tablets
  ...

spi: move more spi_setup() functionality into core

2009-06-18T20:03:42+00:00

Move some common spi_setup() error checks into the SPI framework from the
spi_master controller drivers:

 - Add a new "mode_bits" field to spi_master

 - Use that in spi_setup to validate the spi->mode value being
   requested.  Setting this new field is now mandatory for any
   controller supporting more than vanilla SPI_MODE_0.

 - Update all spi_master drivers to:

     * Initialize that field
     * Remove current spi_setup() checks using that value.

This is a net minor code shrink.

Signed-off-by: David Brownell 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds

spi: move common spi_setup() functionality into core

2009-06-18T20:03:42+00:00

Start moving some spi_setup() functionality into the SPI core from the
various spi_master controller drivers:

 - Make that function stop being an inline;

 - Move two common idioms from drivers into that new function:
    * Default bits_per_word to 8 if that field isn't set
    * Issue a standardized dev_dbg() message

This is a net minor source code shrink, and supports enhancments found in
some follow-up patches.

Signed-off-by: David Brownell 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds

net/libertas: remove GPIO-CS handling in SPI interface code

2009-06-10T17:27:50+00:00

This removes the dependency on GPIO framework and lets the SPI host
driver handle the chip select. The SPI host driver is required to keep
the CS active for the entire message unless cs_change says otherwise.
This patch collects the two/three single SPI transfers into a message.
Also the delay in read path in case use_dummy_writes are not used is
moved into the SPI host driver.

Tested-by: Mike Rapoport 
Tested-by: Andrey Yurovsky 
Signed-off-by: Sebastian Andrzej Siewior 
Acked-by: Dan Williams 
Signed-off-by: John W. Linville

Input: ads7846 - support swapping x and y axes

2009-05-20T02:24:54+00:00

Signed-off-by: Michael Roth 
Signed-off-by: Dmitry Torokhov

Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6

2009-05-19T04:08:20+00:00

Conflicts:
	drivers/scsi/fcoe/fcoe.c

wl12xx: add driver

2009-05-06T19:14:54+00:00

wl12xx is a driver for TI wl1251 802.11 chipset designed for embedded
devices, supporting both SDIO and SPI busses. Currently the driver
supports only SPI. Adding support 1253 (the 5 GHz version) should be
relatively easy. More information here:

http://focus.ti.com/general/docs/wtbu/wtbuproductcontent.tsp?contentId=4711&navigationId=12494&templateId=6123

(Collapsed original sequence of pre-merge patches into single commit for
initial merge. -- JWL)

Signed-off-by: Kalle Valo 
Signed-off-by: Bob Copeland 
Signed-off-by: John W. Linville

spi: documentation: emphasise spi_master.setup() semantics

2009-04-21T20:41:50+00:00

This is a doc-only patch which I hope will reduce the number of
spi_master controller driver patches starting out with a common
implementation bug.

(As in: almost every spi_master driver I see starts out with its
version of this bug.  Sigh.)

It just re-emphasizes that the setup() method may be called for one
device while a transfer is active on another ...  which means that most
driver implementations shouldn't touch any registers.

Signed-off-by: David Brownell 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds