Add the MAX7300-I2C variant of the MAX7301-SPI version.  Both chips share
the same core logic, so the generic part of the in-kernel SPI-driver is
refactored into a generic part.  The I2C and SPI specific funtions are
then wrapped into seperate drivers picking up the generic part.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Juergen Beisert <j.beisert@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: update multi-touch protocol documentation
  Input: add the ABS_MT_PRESSURE event
  Input: winbond-cir - remove dmesg spam
  Input: lifebook - add another Lifebook DMI signature
  Input: ad7879 - support auxiliary GPIOs via gpiolib

The driver core allows for a platform-specific chipselect assert/deassert
function, however the chipselect function in the core doesn't take advantage
of this fact.

This enables the use of a custom function, should it be defined.

Signed-off-by: George Shore <george@georgeshore.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

Now dw_spi core fully supports 3 transfer modes: pure polling,
DMA and IRQ mode. IRQ mode will use the FIFO half empty as
the IRQ trigger, so each interface driver need set the fifo_len,
so that core driver can handle it properly

Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

Drop the simple fancy sysfs hooks for the aux GPIOs and expose these via
the gpiolib interface so that other drivers can use them.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
  spi: spi_txx9.c: use resource_size()
  spi: spi_sh_sci.c: use resource_size()
  spi: spi_mpc8xxx.c: use resource_size()
  spi: spi_bfin5xx.c: use resource_size()
  spi: atmel_spi.c: use resource_size()
  spi: Add s3c64xx SPI Controller driver
  atmel_spi: fix dma addr calculation for len > BUFFER_SIZE
  spi_s3c24xx: add FIQ pseudo-DMA support
  spi: controller driver for Designware SPI core
  spidev: add proper section markers
  spidev: use DECLARE_BITMAP instead of declaring the array

Driver for the Designware SPI core, it supports multipul interfaces like
PCI/APB etc.  User can use "dw_apb_ssi_db.pdf" from Synopsys as HW
datasheet.

[randy.dunlap@oracle.com: fix build]
[akpm@linux-foundation.org: build fix]
Signed-off-by: Feng Tang <feng.tang@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (23 commits)
  spi: fix probe/remove section markings
  Add OMAP spi100k driver
  spi-imx: don't access struct device directly but use dev_get_platdata
  spi-imx: Add mx25 support
  spi-imx: use positive logic to distinguish cpu variants
  spi-imx: correct check for platform_get_irq failing
  ARM: NUC900: Add spi driver support for nuc900
  spi: SuperH MSIOF SPI Master driver V2
  spi: fix spidev compilation failure when VERBOSE is defined
  spi/au1550_spi: fix setupxfer not to override cfg with zeros
  spi/mpc8xxx: don't use __exit_p to wrap plat_mpc8xxx_spi_remove
  spi/i.MX: fix broken error handling for gpio_request
  spi/i.mx: drain MXC SPI transfer buffer when probing device
  MAINTAINERS: add SPI co-maintainer.
  spi/xilinx_spi: fix incorrect casting
  spi/mpc52xx-spi: minor cleanups
  xilinx_spi: add a platform driver using the xilinx_spi common module.
  xilinx_spi: add support for the DS570 IP.
  xilinx_spi: Switch to iomem functions and support little endian.
  xilinx_spi: Split into of driver and generic part.
  ...

This patch is V2 of SPI Master support for the SuperH MSIOF.
Full duplex, spi mode 0-3, active high cs, 3-wire and lsb
first should all be supported, but the driver has so far
only been tested with "mmc_spi".

The MSIOF hardware comes with 32-bit FIFOs for receive and
transmit, and this driver simply breaks the SPI messages
into FIFO-sized chunks. The MSIOF hardware manages the pins
for clock, receive and transmit (sck/miso/mosi), but the chip
select pin is managed by software and must be configured as
a regular GPIO pin by the board code.

Performance wise there is still room for improvement, but
on a Ecovec board with the built-in sh7724 MSIOF0 this driver
gets Mini-sd read speeds of about half a megabyte per second.

Future work include better clock setup and merging of 8-bit
transfers into 32-bit words to reduce interrupt load and
improve throughput.

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>