The Epson LCD L4F00242T03 is mounted on the Freescale i.MX31 PDK board. 
Based upon Marek Vasut work in l4f00242t03.c, this driver provides
basic init and power on/off functionality for this device through the
sysfs lcd interface.

Unfortunately Datasheet for this device are not available and
all the control sequences sent to the display were copied from the
freescale driver that in the i.MX31 Linux BSP.

As in the i.MX31PDK board the core and io suppliers are voltage
regulators, that functionality is embedded here, but not strict.

Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>

Add wakeup support to the ads7846 driver. Platforms can enable wakeup
capability by setting the wakeup flag in ads7846_platform_data. With this
patch the ads7846 driver can be used to wake the system from suspend.

Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

The AD7873 is almost identical to the ADS7846; the only difference is
related to the Power Management bits PD0 and PD1.  This results in a
slightly different PENIRQ enable behavior.  For the AD7873, VREF should
be turned off during differential measurements.

So, add the AD7873/43 to the list of driver supported devices, and prevent
VREF usage during differential/ratiometric conversion modes.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Add the MAX7300-I2C variant of the MAX7301-SPI version.  Both chips share
the same core logic, so the generic part of the in-kernel SPI-driver is
refactored into a generic part.  The I2C and SPI specific funtions are
then wrapped into seperate drivers picking up the generic part.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Juergen Beisert <j.beisert@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: update multi-touch protocol documentation
  Input: add the ABS_MT_PRESSURE event
  Input: winbond-cir - remove dmesg spam
  Input: lifebook - add another Lifebook DMI signature
  Input: ad7879 - support auxiliary GPIOs via gpiolib

The driver core allows for a platform-specific chipselect assert/deassert
function, however the chipselect function in the core doesn't take advantage
of this fact.

This enables the use of a custom function, should it be defined.

Signed-off-by: George Shore <george@georgeshore.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

Now dw_spi core fully supports 3 transfer modes: pure polling,
DMA and IRQ mode. IRQ mode will use the FIFO half empty as
the IRQ trigger, so each interface driver need set the fifo_len,
so that core driver can handle it properly

Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

Drop the simple fancy sysfs hooks for the aux GPIOs and expose these via
the gpiolib interface so that other drivers can use them.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
  spi: spi_txx9.c: use resource_size()
  spi: spi_sh_sci.c: use resource_size()
  spi: spi_mpc8xxx.c: use resource_size()
  spi: spi_bfin5xx.c: use resource_size()
  spi: atmel_spi.c: use resource_size()
  spi: Add s3c64xx SPI Controller driver
  atmel_spi: fix dma addr calculation for len > BUFFER_SIZE
  spi_s3c24xx: add FIQ pseudo-DMA support
  spi: controller driver for Designware SPI core
  spidev: add proper section markers
  spidev: use DECLARE_BITMAP instead of declaring the array