linux-toradex.git/include/linux/usb.h, branch v3.7

USB: usb.h: remove dbg() macro

2012-10-17T18:16:13+00:00

There are no users of this macro anymore in the kernel tree, so finally
delete it.

Signed-off-by: Greg Kroah-Hartman

usb/acpi: Use ACPI methods to power off ports.

2012-09-10T20:04:01+00:00

Upcoming Intel systems will have an ACPI method to control whether a USB
port can be completely powered off.  The implication of powering off a
USB port is that the device and host sees a physical disconnect, and
subsequent port connections and remote wakeups will be lost.

Add a new function, usb_acpi_power_manageable(), that can be used to
find whether the usb port has ACPI power resources that can be used to
power on and off the port on these machines. Also add a new function
called usb_acpi_set_power_state() that controls the port power via these
ACPI methods.

When the USB core calls into the xHCI hub driver to power off a port,
check whether the port can be completely powered off via this new ACPI
mechanism.  If so, call into these new ACPI methods.  Also use the ACPI
methods when the USB core asks to power on a port.

Signed-off-by: Lan Tianyu 
Signed-off-by: Sarah Sharp 
Signed-off-by: Greg Kroah-Hartman

usb/acpi: Store info on device removability.

2012-09-10T20:04:01+00:00

In the upcoming USB port power off patches, we need to know whether a
USB port can ever see a disconnect event.  Often USB ports are internal
to a system, and users can't disconnect USB devices from that port.
Sometimes those ports will remain empty, because the OEM chose not to
connect an internal USB device to that port.

According to ACPI Spec 9.13, PLD indicates whether USB port is
user visible and _UPC indicates whether a USB device can be connected to
the USB port (we'll call this "connectible").  Here's a matrix of the
possible combinations:

Visible Connectible
		Name		Example
-------------------------------------------------------------------------

Yes	No	Unknown		(Invalid state.)

Yes	Yes	Hot-plug	USB ports on the outside of a laptop.
				A user could freely connect and disconnect
				USB devices.

No	Yes	Hard-wired	A USB modem hard-wired to a port on the
				inside of a laptop.

No	No	Not used	The port is internal to the system and
				will remain empty.

Represent each of these four states with an enum usb_port_connect_type.
The four states are USB_PORT_CONNECT_TYPE_UNKNOWN,
USB_PORT_CONNECT_TYPE_HOT_PLUG, USB_PORT_CONNECT_TYPE_HARD_WIRED, and
USB_PORT_NOT_USED.  When we get the USB port's acpi_handle, store the
state in connect_type in struct usb_port.

Signed-off-by: Lan Tianyu 
Signed-off-by: Sarah Sharp 
Signed-off-by: Greg Kroah-Hartman

usb: move children to struct usb_port

2012-09-10T19:59:42+00:00

The usb_device structure contains an array of usb_device "children".
This array is only valid if the usb_device is a hub, so it makes no
sense to store it there.  Instead, store the usb_device child
in its parent usb_port structure.

Since usb_port is an internal USB core structure, add a new function to
get the USB device child, usb_hub_find_child().  Add a new macro,
usb_hub_get_each_child(), to iterate over all the children attached to a
particular USB hub.

Remove the printing the USB children array pointer from the usb-ip
driver, since it's really not necessary.

Acked-by: Alan Stern 
Signed-off-by: Lan Tianyu 
Signed-off-by: Sarah Sharp 
Signed-off-by: Greg Kroah-Hartman

USB: add USB_VENDOR_AND_INTERFACE_INFO() macro

2012-07-17T00:43:04+00:00

A lot of Broadcom Bluetooth devices provides vendor specific interface
class and we are getting flooded by patches adding new device support.
This change will help us enable support for any other Broadcom with vendor
specific device that arrives in the future.

Only the product id changes for those devices, so this macro would be
perfect for us:

{ USB_VENDOR_AND_INTERFACE_INFO(0x0a5c, 0xff, 0x01, 0x01) }

Signed-off-by: Marcel Holtmann 
Signed-off-by: Gustavo Padovan 
Acked-by: Henrik Rydberg 
Signed-off-by: Greg Kroah-Hartman

USB: remove 8 bytes of padding from usb_host_interface on 64 bit builds

2012-07-17T00:21:29+00:00

Reorder elements in the usb_host_interface structure to remove 8 bytes
of padding on 64 bit builds , and so shrink it's size to 40 bytes.

usb_interface_descriptor is a odd size which leaves a gap that is not
big enough to hold a pointer, so moving extralen into that gap removes
the need for more padding.

Signed-off-by: Richard Kennedy 
Signed-off-by: Greg Kroah-Hartman

USB: Add a sysfs file to show LTM capabilities.

2012-07-11T11:06:48+00:00

USB 3.0 devices can optionally support Latency Tolerance Messaging
(LTM).  Add a new sysfs file in the device directory to show whether a
device is LTM capable.  This file will be present for both USB 2.0 and
USB 3.0 devices.

Signed-off-by: Sarah Sharp

USB: Enable Latency Tolerance Messaging (LTM).

2012-07-11T11:06:48+00:00

USB 3.0 devices may optionally support a new feature called Latency
Tolerance Messaging.  If both the xHCI host controller and the device
support LTM, it should be turned on in order to give the system hardware
a better clue about the latency tolerance values of its PCI devices.

Once a Set Feature request to enable LTM is received, the USB 3.0 device
will begin to send LTM updates as its buffers fill or empty, and it can
tolerate more or less latency.

The USB 3.0 spec, section C.4.2 says that LTM should be disabled just
before the device is placed into suspend.  Then the device will send an
updated LTM notification, so that the system doesn't think it should
remain in an active state in order to satisfy the latency requirements
of the suspended device.

The Set and Clear Feature LTM enable command can only be sent to a
configured device.  The device will respond with an error if that
command is sent while it is in the Default or Addressed state.  Make
sure to check udev->actconfig in usb_enable_ltm() and usb_disable_ltm(),
and don't send those commands when the device is unconfigured.

LTM should be enabled once a new configuration is installed in
usb_set_configuration().  If we end up sending duplicate Set Feature LTM
Enable commands on a switch from one installed configuration to another
configuration, that should be harmless.

Make sure that LTM is disabled before the device is unconfigured in
usb_disable_device().  If no drivers are bound to the device, it doesn't
make sense to allow the device to control the latency tolerance of the
xHCI host controller.

Signed-off-by: Sarah Sharp

USB: Remove unused LPM variable.

2012-07-11T11:06:47+00:00

hub_initiated_lpm_disable_count is not used by any code, so remove it.

This commit should be backported to kernels as old as 3.5, that contain
the commit 8306095fd2c1100e8244c09bf560f97aca5a311d "USB: Disable USB
3.0 LPM in critical sections."

Signed-off-by: Sarah Sharp 
Cc: stable@vger.kernel.org

usbdevfs: Add a USBDEVFS_GET_CAPABILITIES ioctl

2012-07-06T17:53:19+00:00

There are a few (new) usbdevfs capabilities which an application cannot
discover in any other way then checking the kernel version. There are 3
problems with this:
1) It is just not very pretty.
2) Given the tendency of enterprise distros to backport stuff it is not
reliable.
3) As discussed in length on the mailinglist, USBDEVFS_URB_BULK_CONTINUATION
does not work as it should when combined with USBDEVFS_URB_SHORT_NOT_OK
(which is its intended use) on devices attached to an XHCI controller.
So the availability of these features can be host controller dependent,
making depending on them based on the kernel version not a good idea.

This patch besides adding the new ioctl also adds flags for the following
existing capabilities:

USBDEVFS_CAP_ZERO_PACKET,        available since 2.6.31
USBDEVFS_CAP_BULK_CONTINUATION,  available since 2.6.32, except for XHCI
USBDEVFS_CAP_NO_PACKET_SIZE_LIM, available since 3.3

Note that this patch only does not advertise the USBDEVFS_URB_BULK_CONTINUATION
cap for XHCI controllers, bulk transfers with this flag set will still be
accepted when submitted to XHCI controllers.

Returning -EINVAL for them would break existing apps, and in most cases the
troublesome scenario wrt USBDEVFS_URB_SHORT_NOT_OK urbs on XHCI controllers
will never get hit, so this would break working use cases.

The disadvantage of not returning -EINVAL is that cases were it is causing
real trouble may go undetected / the cause of the trouble may be unclear,
but this is the best we can do.

Signed-off-by: Hans de Goede 
Acked-by: Alan Stern 
Acked-by: Sarah Sharp 
Signed-off-by: Greg Kroah-Hartman