Currently, the USB hub core waits for 50 ms after enumerating the
device. This was added to help "some high speed devices" to
enumerate (b789696af8 "[PATCH] USB: relax usbcore reset timings").

On some devices, the time-to-active is important, so we provide
a per-port option to reduce the time to what the USB specification
requires: 10 ms.

Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The "old" enumeration scheme is considerably faster (it takes
~244ms instead of ~356ms to get the descriptor).

It is currently only possible to use the old scheme globally
(/sys/module/usbcore/parameters/old_scheme_first), which is not
desirable as the new scheme was introduced to increase compatibility
with more devices.

However, in our case, we care about time-to-active for a specific
USB device (which we make the firmware for), on a specific port
(that is pogo-pin based: not a standard USB port). This new
sysfs option makes it possible to use the old scheme on a single
port only.

Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB 3.2 specification adds Dual-lane support, doubling the maximum
SuperSpeedPlus data rate from 10Gbps to 20Gbps.

Dual-lane takes into use a second set of rx and tx wires/pins in the
Type-C cable and connector.

Add "rx_lanes" and "tx_lanes" variables to struct usb_device to store
the numer of lanes in use. Number of lanes can be read using the extended
port status hub request that was introduced in USB 3.1.

Extended port status rx and tx lane count are zero based, maximum
lanes supported by non inter-chip (SSIC) USB 3.2 is 2 (dual lane) with
rx and tx lane count symmetric. SSIC devices support asymmetric lanes
up to 4 lanes per direction.

If extended port status is not available then default to one lane.

Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB SS and SSP hubs provide wHubDelay values on their hub descriptor
which we should inform the USB Device about.

The USB Specification 3.0 explains, on section 9.4.11, how to
calculate the value and how to issue the request. Note that a
USB_REQ_SET_ISOCH_DELAY is valid on all device states (Default,
Address, Configured), we just *chose* to issue it from Address state
right after successfully fetching the USB Device Descriptor.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The URB_NO_FSBR flag has never really been used.  It was introduced as
a potential way for UHCI to minimize PCI bus usage (by not attempting
full-speed bulk and control transfers more than once per frame), but
the flag was not set by any drivers.

There's no point in keeping it around.  This patch simplifies the API
by removing it.  Unfortunately, it does have to be kept as part of the
usbfs ABI, but at least we can document in
include/uapi/linux/usbdevice_fs.h that it doesn't do anything.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull sound updates from Takashi Iwai:
 "There are no big surprising changes in this cycle, yet not too boring,
  either. The biggest change from diffstat POV is the removal of the
  legacy OSS driver codes that have been already disabled for a long
  time. This will bring a few trivial merge conflicts.

  As new features in ASoC side, there are two things: a new AC97 bus
  implementation and AMD Stony platform support. Both include the
  relevant changes shared with other subsystems, e.g. AC97 MFD changes
  and DRM AMD changes.

  Some other highlighted topics are:

   - A bunch of USB-audio drivers got the hardening against the
     malicious device accesses with a new helper code for endpoint
     sanity check

   - Lots of cleanups for ASoC Intel platform code, including support
     for their open source audio firmware

   - Continued ASoC core componentization works

   - Support for scaling MCLK with sample rate in ASoC simple-card

   - Stabler PCM hot-unplug capability, especially for ASoC usages"

* tag 'sound-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (302 commits)
  Documentation: sound: hd-audio: notes.rst
  ASoC: bcm2835: Support left/right justified and DSP modes
  ASoC: bcm2835: Enforce full symmetry
  ASoC: bcm2835: Support additional samplerates up to 384kHz
  ASoC: bcm2835: Add support for TDM modes
  ASoC: add mclk-fs support to audio graph card
  ASoC: add mclk-fs to audio graph card binding
  ASoC: rt5514: work around link error
  ASoC: rt5514: mark PM functions as __maybe_unused
  ASoC: rt5663: Check the JD status in the button pushing
  ASoC: amd: Modified DMA transfer Mechanism for Playback
  ASoC: rt5645: Wait for 400msec before concluding on value of RT5645_VENDOR_ID2
  ASoC: sun4i-codec: fixed 32bit audio capture support for H3/H2+
  ASoC: da7213: add support for DSP modes
  ASoC: sun8i-codec: Add a comment on the LRCK inversion
  ASoC: sun8i-codec: Set the BCLK divider
  ASoC: rt5663: Delay and retry reading rt5663 ID register
  ASoC: amd: use do_div rather than 64 bit division to fix 32 bit builds
  ASoC: cs42l56: Fix reset GPIO name in example DT binding
  ASoC: rt5514-spi: check irq status to schedule data copy in resume function
  ...

Pull USB/PHY updates from Greg KH:
 "Here is the big set of USB and PHY driver updates for 4.15-rc1.

  There is the usual amount of gadget and xhci driver updates, along
  with phy and chipidea enhancements. There's also a lot of SPDX tags
  and license boilerplate cleanups as well, which provide some churn in
  the diffstat.

  Other major thing is the typec code that moved out of staging and into
  the "real" part of the drivers/usb/ tree, which was nice to see
  happen.

  All of these have been in linux-next with no reported issues for a
  while"

* tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
  usb: gadget: f_fs: Fix use-after-free in ffs_free_inst
  USB: usbfs: compute urb->actual_length for isochronous
  usb: core: message: remember to reset 'ret' to 0 when necessary
  USB: typec: Remove remaining redundant license text
  USB: typec: add SPDX identifiers to some files
  USB: renesas_usbhs: rcar?.h: add SPDX tags
  USB: chipidea: ci_hdrc_tegra.c: add SPDX line
  USB: host: xhci-debugfs: add SPDX lines
  USB: add SPDX identifiers to all remaining Makefiles
  usb: host: isp1362-hcd: remove a couple of redundant assignments
  USB: adutux: remove redundant variable minor
  usb: core: add a new usb_get_ptm_status() helper
  usb: core: add a 'type' parameter to usb_get_status()
  usb: core: introduce a new usb_get_std_status() helper
  usb: core: rename usb_get_status() 'type' argument to 'recip'
  usb: core: add Status Type definitions
  USB: gadget: Remove redundant license text
  USB: gadget: function: Remove redundant license text
  USB: gadget: udc: Remove redundant license text
  USB: gadget: legacy: Remove redundant license text
  ...

ASoC: Updates for v4.15

The biggest thing this release has been the conversion of the AC98 bus
to the driver model, that's been a long time coming so thanks to Robert
Jarzmik for his dedication there.  Due to there being some AC97 MFD
there's a few fairly large changes in input and the MFD layer, mainly to
the wm97xx driver.

There's also some drivers/drm changes to support the new AMD Stoney
platform, these are shared with the DRM subsystem and should be being
merged via both.

Within the subsystem the overwhelming bulk of the changes is in the
Intel drivers which continue to need lots of cleanups and fixes, this
release they've also gained support for their open source firmware.
There's also some large changs in the core as Morimoto-san continues to
mirror operations into the component level in preparation for conversion
of drivers to that.

 - The AC97 bus has finally caught up with the driver model thanks to
   some dedicated and persistent work from Robert Jarzmik.
 - Continued work from Morimoto-san on moving us towards being able to
   use components for everything.
 - Lots of cleanups for the Intel platform code, including support for
   their open source audio firmware.
 - Support for scaling MCLK with sample rate in simple-card.
 - Support for AMD Stoney platform.

Drivers who are interested in the PTM status stype, should use this
new helper to make sure they issue the correct GetStatus message.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This new 'type' parameter will allows interested drivers to request
for PTM status or Standard status.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>