linux-toradex.git/include/linux/usb, branch v2.6.32.39 Linux kernel for Apalis and Colibri modules USB: serial: handle Data Carrier Detect changes 2011-02-17T23:36:44+00:00 Libor Pechacek lpechacek@suse.cz 2011-01-14T13:30:21+00:00 6fe7015007299e14f5ea212a503bcba5958c7086 commit d14fc1a74e846d7851f24fc9519fe87dc12a1231 upstream. Alan's commit 335f8514f200e63d689113d29cb7253a5c282967 introduced .carrier_raised function in several drivers. That also means tty_port_block_til_ready can now suspend the process trying to open the serial port when Carrier Detect is low and put it into tty_port.open_wait queue. We need to wake up the process when Carrier Detect goes high and trigger TTY hangup when CD goes low. Some of the devices do not report modem status line changes, or at least we don't understand the status message, so for those we remove .carrier_raised again. Signed-off-by: Libor Pechacek <lpechacek@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> 
commit d14fc1a74e846d7851f24fc9519fe87dc12a1231 upstream.

Alan's commit 335f8514f200e63d689113d29cb7253a5c282967 introduced
.carrier_raised function in several drivers.  That also means
tty_port_block_til_ready can now suspend the process trying to open the serial
port when Carrier Detect is low and put it into tty_port.open_wait queue.  We
need to wake up the process when Carrier Detect goes high and trigger TTY
hangup when CD goes low.

Some of the devices do not report modem status line changes, or at least we
don't understand the status message, so for those we remove .carrier_raised
again.

Signed-off-by: Libor Pechacek <lpechacek@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB delay init quirk for logitech Harmony 700-series devices 2010-08-13T20:19:42+00:00 Phil Dibowitz phil@ipom.com 2010-07-21T22:05:01+00:00 739e7616fda378c0050fd4f2bcdfc1b81212013e commit 93362a875fc69881ae69299efaf19a55a1f57db0 upstream. The Logitech Harmony 700 series needs an extra delay during initialization. This patch adds a USB quirk which enables such a delay and adds the device to the quirks list. Signed-off-by: Phil Dibowitz <phil@ipom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> 
commit 93362a875fc69881ae69299efaf19a55a1f57db0 upstream.

The Logitech Harmony 700 series needs an extra delay during
initialization.  This patch adds a USB quirk which enables such a delay
and adds the device to the quirks list.

Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: serial: don't call release without attach 2009-10-09T20:52:05+00:00 Alan Stern stern@rowland.harvard.edu 2009-10-09T16:43:12+00:00 a4720c650b68a5fe7faed2edeb0ad12645f7ae63 This patch (as1295) fixes a recently-added bug in the USB serial core. If certain kinds of errors occur during probing, the core may call a serial driver's release method without previously calling the attach method. This causes some drivers (io_ti in particular) to perform an invalid memory access. The patch adds a new flag to keep track of whether or not attach has been called. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Jean-Denis Girard <jd.girard@sysnux.pf> CC: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> 
This patch (as1295) fixes a recently-added bug in the USB serial core.
If certain kinds of errors occur during probing, the core may call a
serial driver's release method without previously calling the attach
method.  This causes some drivers (io_ti in particular) to perform an
invalid memory access.

The patch adds a new flag to keep track of whether or not attach has
been called.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Jean-Denis Girard <jd.girard@sysnux.pf>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Merge branch 'master' of /home/davem/src/GIT/linux-2.6/ 2009-09-24T22:13:11+00:00 David S. Miller davem@davemloft.net 2009-09-24T22:13:11+00:00 8b3f6af86378d0a10ca2f1ded1da124aef13b62c Conflicts: drivers/staging/Kconfig drivers/staging/Makefile drivers/staging/cpc-usb/TODO drivers/staging/cpc-usb/cpc-usb_drv.c drivers/staging/cpc-usb/cpc.h drivers/staging/cpc-usb/cpc_int.h drivers/staging/cpc-usb/cpcusb.h 
Conflicts:
	drivers/staging/Kconfig
	drivers/staging/Makefile
	drivers/staging/cpc-usb/TODO
	drivers/staging/cpc-usb/cpc-usb_drv.c
	drivers/staging/cpc-usb/cpc.h
	drivers/staging/cpc-usb/cpc_int.h
	drivers/staging/cpc-usb/cpcusb.h
USB: ehci-dbgp: errata for EHCI debug controller initialization 2009-09-23T13:46:38+00:00 Jason Wessel jason.wessel@windriver.com 2009-08-20T20:39:55+00:00 aab2d4086a1876fcff282aa36e2d4a92aa9935c9 On some EHCI usb debug controllers, the EHCI debug device will fail to be seen after a port reset, after a warm reset. Two options exist to get the device to initialize correctly. Option 1 is to unplug and plug in the device. Option 2 is to use the EHCI port test to get the usb debug device to start talking again. At that point the debug controller port reset will succeed. Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Yinghai Lu <yinghai@kernel.org> Cc: "Eric W. Biederman" <ebiederm@xmission.com> CC: dbrownell@users.sourceforge.net Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> 
On some EHCI usb debug controllers, the EHCI debug device will fail to
be seen after a port reset, after a warm reset.  Two options exist to
get the device to initialize correctly.

Option 1 is to unplug and plug in the device.

Option 2 is to use the EHCI port test to get the usb debug device to
start talking again.  At that point the debug controller port reset
will succeed.

Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
CC: dbrownell@users.sourceforge.net
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: ehci-dbgp,ehci: Allow early or late use of the dbgp device 2009-09-23T13:46:38+00:00 Jason Wessel jason.wessel@windriver.com 2009-08-20T20:39:54+00:00 8d053c79f22462f55c02c8083580730b922cf7b4 If the EHCI debug port is initialized and in use, the EHCI host controller driver must follow two rules. 1) If the EHCI host driver issues a controller reset, the debug controller driver re-initialization must get called after the reset is completed. 2) The EHCI host driver should ignore any requests to the physical EHCI debug port when the EHCI debug port is in use. The code to check for the debug port was moved from ehci_pci_reinit() to ehci_pci_setup because it must get called prior to ehci_reset() which will clear the debug port registers. Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: dbrownell@users.sourceforge.net Cc: Ingo Molnar <mingo@elte.hu> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Yinghai Lu <yinghai@kernel.org> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> 
If the EHCI debug port is initialized and in use, the EHCI host
controller driver must follow two rules.

1) If the EHCI host driver issues a controller reset, the debug
   controller driver re-initialization must get called after the reset
   is completed.

2) The EHCI host driver should ignore any requests to the physical
   EHCI debug port when the EHCI debug port is in use.

The code to check for the debug port was moved from ehci_pci_reinit()
to ehci_pci_setup because it must get called prior to ehci_reset()
which will clear the debug port registers.

Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: dbrownell@users.sourceforge.net
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: ehci-dbgp: stability improvements and external re-init 2009-09-23T13:46:38+00:00 Jason Wessel jason.wessel@windriver.com 2009-08-20T20:39:53+00:00 917778267fbe67703ab7d5c6f0b7a05d4c3df485 This patch implements several changes: 1) Improve the capability to debug the dbgp driver The dbgp_ehci_status() was added in a number of places to report the critical ehci registers to diagnose the cause of a failure of the ehci-dbgp driver. 2) Capability to survive the host controller initialization The dbgp_external_startup(), dbgp_not_safe, and dbgp_phys_port were added so as to allow the ehci-dbgp to re-initialize after the ehci host controller is reset by the standard host controller driver. This same routine is common for the early startup or re-initialization. This resulted in the need to move some of the initialization code out of the __init section because the ehci driver has the possibility to be loaded later on as a kernel module. 3) Stability improvements for device initialization The device enumeration from 0 to 127 has the possibility to fail the first time after a warm reset on some older EHCI debug controllers. The enumeration will be tried up to 3 times to account for this failure case. The dbg_wait_until_complete() was changed to wait up to 250 ms before failing which only comes into play during device initialization. The maximum delay will never get hit during the course of normal operation of the driver, unless the device got unplugged or there was a ehci controller failure, in which case the dbgp device driver will shut itself down. Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: dbrownell@users.sourceforge.net Cc: Yinghai Lu <yinghai@kernel.org> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> 
This patch implements several changes:

1) Improve the capability to debug the dbgp driver

   The dbgp_ehci_status() was added in a number of places to report
   the critical ehci registers to diagnose the cause of a failure of
   the ehci-dbgp driver.

2) Capability to survive the host controller initialization

   The dbgp_external_startup(), dbgp_not_safe, and dbgp_phys_port were
   added so as to allow the ehci-dbgp to re-initialize after the ehci
   host controller is reset by the standard host controller driver.
   This same routine is common for the early startup or
   re-initialization.

   This resulted in the need to move some of the initialization code
   out of the __init section because the ehci driver has the
   possibility to be loaded later on as a kernel module.

3) Stability improvements for device initialization

   The device enumeration from 0 to 127 has the possibility to fail
   the first time after a warm reset on some older EHCI debug
   controllers.  The enumeration will be tried up to 3 times to
   account for this failure case.

   The dbg_wait_until_complete() was changed to wait up to 250 ms
   before failing which only comes into play during device
   initialization. The maximum delay will never get hit during the
   course of normal operation of the driver, unless the device got
   unplugged or there was a ehci controller failure, in which case the
   dbgp device driver will shut itself down.

Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: dbrownell@users.sourceforge.net
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: ehci,dbgp,early_printk: split ehci debug driver from early_printk.c 2009-09-23T13:46:38+00:00 Jason Wessel jason.wessel@windriver.com 2009-08-20T20:39:48+00:00 df6c516900d48df3581b23d37d6516a22ec4f2ca Move the dbgp early printk driver in advance of refactoring and adding new code, so the changes to this code are tracked separately from the move of the code. The drivers/usb/early directory will be the location of the current and future early usb code for driving usb devices prior initializing the standard interrupt driven USB drivers. Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Yinghai Lu <yinghai@kernel.org> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> 
Move the dbgp early printk driver in advance of refactoring and adding
new code, so the changes to this code are tracked separately from the
move of the code.

The drivers/usb/early directory will be the location of the current
and future early usb code for driving usb devices prior initializing
the standard interrupt driven USB drivers.

Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: use kfifo to buffer usb-generic serial writes 2009-09-23T13:46:34+00:00 David VomLehn dvomlehn@cisco.com 2009-08-28T19:54:27+00:00 8e8dce065088833fc418bfa5fbf035cb0726c04c When do_output_char() attempts to write a carriage return/line feed sequence, it first checks to see how much buffer room is available. If there are at least two characters free, it will write the carriage return/line feed with two calls to tty_put_char(). It calls the tty_operation functions write() for devices that don't support the tty_operations function put_char(). If the USB generic serial device's write URB is not in use, it will return the buffer size when asked how much room is available. The write() of the carriage return will cause it to mark the write URB busy, so the subsequent write() of the line feed will be ignored. This patch uses the kfifo infrastructure to implement a write FIFO that accurately returns the amount of space available in the buffer. Signed-off-by: David VomLehn <dvomlehn@cisco.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> 
When do_output_char() attempts to write a carriage return/line feed sequence,
it first checks to see how much buffer room is available. If there are at least
two characters free, it will write the carriage return/line feed with two calls
to tty_put_char(). It calls the tty_operation functions write() for devices that
don't support the tty_operations function put_char(). If the USB generic serial
device's write URB is not in use, it will return the buffer size when asked how
much room is available. The write() of the carriage return will cause it to mark
the write URB busy, so the subsequent write() of the line feed will be ignored.

This patch uses the kfifo infrastructure to implement a write FIFO that
accurately returns the amount of space available in the buffer.

Signed-off-by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: audio: guard kernel-only code with __KERNEL__ 2009-09-23T13:46:31+00:00 Michael S. Tsirkin mst@redhat.com 2009-07-29T11:23:25+00:00 c35013087aa9b10e4674b53b7c8f7966de83c194 include/linux/usb/audio.h is exported to userspace, so part of this file that is for internal kernel usage need to be guarded with ifdef __KERNEL__. This way make headers_install will stript it out. Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> 
include/linux/usb/audio.h is exported to userspace,
so part of this file that is for internal kernel
usage need to be guarded with ifdef __KERNEL__.
This way make headers_install will stript it out.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>