linux-toradex.git/include/linux/usb, branch v4.11-rc3

usb: chipidea: msm: Handle phy power states

2017-01-20T07:27:35+00:00

The ULPI phy on qcom platforms needs to be initialized and
powered on after a USB reset and before we toggle the run/stop
bit. Otherwise, the phy locks up and doesn't work properly. Hook
the phy initialization into the RESET event and the phy power off
into the STOPPED event.

Acked-by: Peter Chen 
Cc: Greg Kroah-Hartman 
Signed-off-by: Stephen Boyd 
Signed-off-by: Peter Chen

usb: chipidea: Consolidate extcon notifiers

2017-01-20T07:13:49+00:00

The two extcon notifiers are almost the same except for the
variable name for the cable structure and the id notifier inverts
the cable->state logic. Make it the same and replace two
functions with one to save some lines. This also makes it so that
the id cable state is true when the id pin is pulled low, so we
change the name of ->state to ->connected to properly reflect
that we're interested in the cable being connected.

Acked-by: Peter Chen 
Cc: Greg Kroah-Hartman 
Cc: "Ivan T. Ivanov" 
Signed-off-by: Stephen Boyd 
Signed-off-by: Peter Chen

usb: chipidea: Add platform flag for wrapper phy management

2017-01-20T03:25:02+00:00

The ULPI phy on qcom platforms needs to be initialized and
powered on after a USB reset and before we toggle the run/stop
bit. Otherwise, the phy locks up and doesn't work properly.
Therefore, add a flag to skip any phy power management in the
core layer, leaving it up to the glue driver to manage.

Acked-by: Peter Chen 
Cc: Greg Kroah-Hartman 
Signed-off-by: Stephen Boyd 
Signed-off-by: Peter Chen

usb: chipidea: Handle extcon events properly

2017-01-20T03:24:35+00:00

We're currently emulating the vbus and id interrupts in the OTGSC
read API, but we also need to make sure that if we're handling
the events with extcon that we don't enable the interrupts for
those events in the hardware. Therefore, properly emulate this
register if we're using extcon, but don't enable the interrupts.
This allows me to get my cable connect/disconnect working
properly without getting spurious interrupts on my device that
uses an extcon for these two events.

Acked-by: Peter Chen 
Cc: Greg Kroah-Hartman 
Cc: "Ivan T. Ivanov" 
Fixes: 3ecb3e09b042 ("usb: chipidea: Use extcon framework for VBUS and ID detect")
Signed-off-by: Stephen Boyd 
Signed-off-by: Peter Chen

Merge tag 'usb-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

2016-12-13T19:10:36+00:00

Pull USB/PHY updates from Greg KH:
 "Here's the big set of USB/PHY patches for 4.10-rc1.

  A number of new drivers are here in this set of changes. We have a new
  USB controller type "mtu3", a new usb-serial driver, and the usual
  churn in the gadget subsystem and the xhci host controller driver,
  along with a few other new small drivers added. And lots of little
  other changes all over the USB and PHY driver tree. Full details are
  in the shortlog

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'usb-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (309 commits)
  USB: serial: option: add dlink dwm-158
  USB: serial: option: add support for Telit LE922A PIDs 0x1040, 0x1041
  USB: OHCI: nxp: fix code warnings
  USB: OHCI: nxp: remove useless extern declaration
  USB: OHCI: at91: remove useless extern declaration
  usb: misc: rio500: fix result type for error message
  usb: mtu3: fix U3 port link issue
  usb: mtu3: enable auto switch from U3 to U2
  usbip: fix warning in vhci_hcd_probe/lockdep_init_map
  usb: core: usbport: Use proper LED API to fix potential crash
  usbip: add missing compile time generated files to .gitignore
  usb: hcd.h: construct hub class request constants from simpler constants
  USB: OHCI: ohci-pxa27x: remove useless functions
  USB: OHCI: omap: remove useless extern declaration
  USB: OHCI: ohci-omap: remove useless functions
  USB: OHCI: ohci-s3c2410: remove useless functions
  USB: cdc-acm: add device id for GW Instek AFG-125
  fsl/usb: Workarourd for USB erratum-A005697
  usb: hub: Wait for connection to be reestablished after port reset
  usbip: vudc: Refactor init_vudc_hw() to be more obvious
  ...

NET: usb: cdc_mbim: add quirk for supporting Telit LE922A

2016-12-08T18:02:25+00:00

Telit LE922A MBIM based composition does not work properly
with altsetting toggle done in cdc_ncm_bind_common.

This patch adds CDC_MBIM_FLAG_AVOID_ALTSETTING_TOGGLE quirk
to avoid this procedure that, instead, is mandatory for
other modems.

Signed-off-by: Daniele Palmas 
Reviewed-by: Bjørn Mork 
Signed-off-by: David S. Miller

usb: hcd.h: construct hub class request constants from simpler constants

2016-12-05T15:37:10+00:00

Currently, each hub class request constant is defined by a line like:
#define ClearHubFeature		(0x2000 | USB_REQ_CLEAR_FEATURE)

The "magic" number for the high byte is one of 0x20, 0xa0, 0x23, 0xa3.
The 0x80 bit that changes inditace USB_DIR_IN, and the 0x03 that
pops up is the difference between USB_RECIP_DEVICE (0x00) and
USB_RECIP_OTHER (0x03). The constant 0x20 bit is USB_TYPE_CLASS.

This patch eliminates those magic numbers by defining a macro to help
construct these hub class request from simpler constants.
Note that USB_RT_HUB is defined as (USB_TYPE_CLASS | USB_RECIP_DEVICE)
and that USB_RT_PORT is defined as (USB_TYPE_CLASS | USB_RECIP_OTHER).

Signed-off-by: Tal Shorer 
Signed-off-by: Greg Kroah-Hartman

usb: gadget: fix request length error for isoc transfer

2016-11-18T11:54:09+00:00

For isoc endpoint descriptor, the wMaxPacketSize is not real max packet
size (see Table 9-13. Standard Endpoint Descriptor, USB 2.0 specifcation),
it may contain the number of packet, so the real max packet should be
ep->desc->wMaxPacketSize && 0x7ff.

Cc: Felipe F. Tonello 
Cc: Felipe Balbi 
Fixes: 16b114a6d797 ("usb: gadget: fix usb_ep_align_maybe
  endianness and new usb_ep_aligna")

Signed-off-by: Peter Chen 
Signed-off-by: Felipe Balbi

usb: gadget: add a new quirk to avoid skb_reserve in u_ether.c

2016-08-31T07:06:03+00:00

Some platforms (e.g. USB-DMAC on R-Car SoCs) has memory alignment
restriction. If memory alignment is not match, the usb peripheral
driver decides not to use the DMA controller. Then, the performance
is not good.

In the case of u_ether.c, since it calls skb_reserve() in rx_submit(),
it is possible to cause memory alignment mismatch.

So, this patch adds a new quirk "quirk_avoids_skb_reserve" to avoid
skb_reserve() calling in u_ether.c to improve performance.

A peripheral driver will set this flag and network gadget drivers
(e.g. f_ncm.c) will reference the flag via gadget_avoids_skb_reserve().

Signed-off-by: Yoshihiro Shimoda 
Signed-off-by: Felipe Balbi

usb: gadget: composite: let USB functions process ctrl reqs in cfg0

2016-08-25T09:13:17+00:00

It can sometimes be necessary for gadget drivers to process non-standard
control requests, which host devices can send without having sent
USB_REQ_SET_CONFIGURATION.

Therefore, the req_match() usb_function method is enhanced with the new
parameter "config0". When a USB configuration is active, this parameter
is false. When a non-core control request is processed in
composite_setup(), without an active configuration, req_match() of the
USB functions of all available configurations which implement this
function, is called with config0=true. Then the control request gets
processed by the first usb_function instance whose req_match() returns
true.

Signed-off-by: Felix Hädicke 
Signed-off-by: Felipe Balbi