Peter writes:

- Improve the over-current handling for imx
- Add the HSIC support for imx

* tag 'usb-ci-v4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
  usb: chipidea: imx: allow to configure oc polarity on i.MX25
  usb: chipidea: imx: Warn if oc polarity isn't specified
  usb: chipidea: imx: support configuring for active low oc signal
  doc: usb: ci-hdrc-usb2: Add pinctrl properties for HSIC pin groups
  usb: chipidea: host: override ehci->hub_control
  usb: chipidea: imx: add HSIC support
  usb: chipidea: add flag for imx hsic implementation

Felipe writes:

USB changes for v4.21

So it looks like folks are interested in dwc3 again. Almost 64% of the
changes are in dwc3 this time around with some other bits in gadget
functions and dwc2.

There are two important parts here: a. removal of the waitqueue from
dwc3's dequeue implementation, which will guarantee that gadget
functions can dequeue from any context and; b. better method for
starting isochronous transfers to avoid, as much as possible, missed
isoc frames.

Apart from these, we have the usual set of non-critical fixes and new
features all over the place.

* tag 'usb-for-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (56 commits)
  usb: dwc2: Fix disable all EP's on disconnect
  usb: dwc3: gadget: Disable CSP for stream OUT ep
  usb: dwc2: disable power_down on Amlogic devices
  Revert "usb: dwc3: pci: Use devm functions to get the phy GPIOs"
  USB: gadget: udc: s3c2410_udc: convert to DEFINE_SHOW_ATTRIBUTE
  usb: mtu3: fix dbginfo in qmu_tx_zlp_error_handler
  usb: dwc3: trace: add missing break statement to make compiler happy
  usb: dwc3: gadget: Report isoc transfer frame number
  usb: gadget: Introduce frame_number to usb_request
  usb: renesas_usbhs: Use SIMPLE_DEV_PM_OPS macro
  usb: renesas_usbhs: Remove dummy runtime PM callbacks
  usb: dwc2: host: use hrtimer for NAK retries
  usb: mtu3: clear SOFTCONN when clear USB3_EN if work as HS mode
  usb: mtu3: enable SETUPENDISR interrupt
  usb: mtu3: fix the issue about SetFeature(U1/U2_Enable)
  usb: mtu3: enable hardware remote wakeup from L1 automatically
  usb: mtu3: remove QMU checksum
  usb/mtu3: power down device ip at setup
  usb: dwc2: Disable power down feature on Samsung SoCs
  usb: dwc3: Correct the logic for checking TRB full in __dwc3_prepare_one_trb()
  ...

NXP (Freecale) imx HSIC design has some special requirements, add
some flags at host code to handle them.

Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>

Add a field frame_number to the usb_request to report the interval
number in (micro)frames in which the isochronous transfer was
transmitted or received. The gadget driver can use this knowledge to
synchronize with the host. Also, this option is useful for debugging
purposes.

Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Nothing to remap, only check length.
Define a minimal structure for CCID descriptor only used to check length.
As this descriptor shares the same value as HID descriptors, keep track and
compare current interface's class to expected HID and CCID standard values.

Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

We want the USB fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

No users of this type anywhere in the tree.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Devices connected under Terminus Technology Inc. Hub (1a40:0101) may
fail to work after the system resumes from suspend:
[  206.063325] usb 3-2.4: reset full-speed USB device number 4 using xhci_hcd
[  206.143691] usb 3-2.4: device descriptor read/64, error -32
[  206.351671] usb 3-2.4: device descriptor read/64, error -32

Info for this hub:
T:  Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  2 Spd=480 MxCh= 4
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1a40 ProdID=0101 Rev=01.11
S:  Product=USB 2.0 Hub
C:  #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub

Some expirements indicate that the USB devices connected to the hub are
innocent, it's the hub itself is to blame. The hub needs extra delay
time after it resets its port.

Hence wait for extra delay, if the device is connected to this quirky
hub.

Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

During HARD_RESET the data link is disconnected.
For self powered device, the spec is advising against doing that.

>From USB_PD_R3_0
7.1.5 Response to Hard Resets
Device operation during and after a Hard Reset is defined as follows:
Self-powered devices Should Not disconnect from USB during a Hard Reset
(see Section 9.1.2).
Bus powered devices will disconnect from USB during a Hard Reset due to the
loss of their power source.

Tackle this by letting TCPM know whether the device is self or bus powered.

This overcomes unnecessary port disconnections from hard reset.
Also, speeds up the enumeration time when connected to Type-A ports.

Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
---------
Version history:
V3:
Rebase on top of usb-next

V2:
Based on feedback from heikki.krogerus@linux.intel.com
- self_powered added to the struct tcpm_port which is populated from
  a. "connector" node of the device tree in tcpm_fw_get_caps()
  b. "self_powered" node of the tcpc_config in tcpm_copy_caps

Based on feedbase from linux@roeck-us.net
- Code was refactored
- SRC_HARD_RESET_VBUS_OFF sets the link state to false based
  on self_powered flag

V1 located here:
https://lkml.org/lkml/2018/9/13/94
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull USB/PHY updates from Greg KH:
 "Here is the big USB/PHY driver patches for 4.20-rc1

  Lots of USB changes in here, primarily in these areas:

   - typec updates and new drivers

   - new PHY drivers

   - dwc2 driver updates and additions (this old core keeps getting
     added to new devices.)

   - usbtmc major update based on the industry group coming together and
     working to add new features and performance to the driver.

   - USB gadget additions for new features

   - USB gadget configfs updates

   - chipidea driver updates

   - other USB gadget updates

   - USB serial driver updates

   - renesas driver updates

   - xhci driver updates

   - other tiny USB driver updates

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'usb-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (229 commits)
  usb: phy: ab8500: silence some uninitialized variable warnings
  usb: xhci: tegra: Add genpd support
  usb: xhci: tegra: Power-off power-domains on removal
  usbip:vudc: BUG kmalloc-2048 (Not tainted): Poison overwritten
  usbip: tools: fix atoi() on non-null terminated string
  USB: misc: appledisplay: fix backlight update_status return code
  phy: phy-pxa-usb: add a new driver
  usb: host: add DT bindings for faraday fotg2
  usb: host: ohci-at91: fix request of irq for optional gpio
  usb/early: remove set but not used variable 'remain_length'
  usb: typec: Fix copy/paste on typec_set_vconn_role() kerneldoc
  usb: typec: tcpm: Report back negotiated PPS voltage and current
  USB: core: remove set but not used variable 'udev'
  usb: core: fix memory leak on port_dev_path allocation
  USB: net2280: Remove ->disconnect() callback from net2280_pullup()
  usb: dwc2: disable power_down on rockchip devices
  usb: gadget: udc: renesas_usb3: add support for r8a77990
  dt-bindings: usb: renesas_usb3: add bindings for r8a77990
  usb: gadget: udc: renesas_usb3: Add r8a774a1 support
  USB: serial: cypress_m8: remove set but not used variable 'iflag'
  ...