If peer uses tiny MSS (say, 75 bytes) and similarly tiny advertised
window, the SWS logic will packetize to half the MSS unnecessarily.

This causes problems with some embedded devices.

However for large MSS devices we do want to half-MSS packetize
otherwise we never get enough packets into the pipe for things
like fast retransmit and recovery to work.

Be careful also to handle the case where MSS > window, otherwise
we'll never send until the probe timer.

Reported-by: ツ Leandro Melo de Sales <leandroal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 30fff923 introduced in linux-2.6.33 (udp: bind() optimisation)
added a secondary hash on UDP, hashed on (local addr, local port).

Problem is that following sequence :

fd = socket(...)
connect(fd, &remote, ...)

not only selects remote end point (address and port), but also sets
local address, while UDP stack stored in secondary hash table the socket
while its local address was INADDR_ANY (or ipv6 equivalent)

Sequence is :
 - autobind() : choose a random local port, insert socket in hash tables
              [while local address is INADDR_ANY]
 - connect() : set remote address and port, change local address to IP
              given by a route lookup.

When an incoming UDP frame comes, if more than 10 sockets are found in
primary hash table, we switch to secondary table, and fail to find
socket because its local address changed.

One solution to this problem is to rehash datagram socket if needed.

We add a new rehash(struct socket *) method in "struct proto", and
implement this method for UDP v4 & v6, using a common helper.

This rehashing only takes care of secondary hash table, since primary
hash (based on local port only) is not changed.

Reported-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

- Do not create expectation when forwarding the PORT
  command to avoid blocking the connection. The problem is that
  nf_conntrack_ftp.c:help() tries to create the same expectation later in
  POST_ROUTING and drops the packet with "dropping packet" message after
  failure in nf_ct_expect_related.

- Change ip_vs_update_conntrack to alter the conntrack
  for related connections from real server. If we do not alter the reply in
  this direction the next packet from client sent to vport 20 comes as NEW
  connection. We alter it but may be some collision happens for both
  conntracks and the second conntrack gets destroyed immediately. The
  connection stucks too.

Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dave reported an rcu lockdep warning on 2.6.35.4 kernel

task->cgroups and task->cgroups->subsys[i] are protected by RCU.
So we avoid accessing invalid pointers here. This might happen,
for example, when you are deref-ing those pointers while someone
move @task from one cgroup to another.

Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As reported by Anton Blanchard when we use
percpu_counter_read_positive() to make our orphan socket limit checks,
the check can be off by up to num_cpus_online() * batch (which is 32
by default) which on a 128 cpu machine can be as large as the default
orphan limit itself.

Fix this by doing the full expensive sum check if the optimized check
triggers.

Reported-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>

The previous value of 672 for L2CAP_DEFAULT_MAX_PDU_SIZE is based on
the default L2CAP MTU.  That default MTU is calculated from the size
of two DH5 packets, minus ACL and L2CAP b-frame header overhead.

ERTM is used with newer basebands that typically support larger 3-DH5
packets, and i-frames and s-frames have more header overhead.  With
clean RF conditions, basebands will typically attempt to use 1021-byte
3-DH5 packets for maximum throughput.  Adjusting for 2 bytes of ACL
headers plus 10 bytes of worst-case L2CAP headers yields 1009 bytes
of payload.

This PDU size imposes less overhead for header bytes and gives the
baseband the option to choose 3-DH5 packets, but is small enough for
ERTM traffic to interleave well with other L2CAP or SCO data.
672-byte payloads do not allow the most efficient over-the-air
packet choice, and cannot achieve maximum throughput over BR/EDR.

Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The L2CAP specification requires that the ERTM retransmit timeout be at
least 2 seconds for BR/EDR connections.

Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Add missing kernel-doc notation to struct sock:

Warning(include/net/sock.h:324): No description found for parameter 'sk_peer_pid'
Warning(include/net/sock.h:324): No description found for parameter 'sk_peer_cred'
Warning(include/net/sock.h:324): No description found for parameter 'sk_classid'
Warning(include/net/sock.h:324): Excess struct/union/enum/typedef member 'sk_peercred' description in 'sock'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>