linux-toradex.git/include/scsi/libsas.h, branch v3.0.95

[SCSI] libsas: Add option for SATA soft reset

2011-05-27T03:49:33+00:00

This allows a libsas driver to optionally provide a soft reset handler
for libata to drive.  The isci driver allows software to control the
assertion/deassertion of SRST.

[jejb: checkpatch.pl fixes]
Signed-off-by: Dave Jiang 
Signed-off-by: Dan Williams 
Signed-off-by: James Bottomley

[SCSI] libsas: fix definition of wideport, include local sas address

2010-12-21T18:23:53+00:00

To date libsas has only looked at the attached sas address when
determining the formation of wide ports.  The specification and some
hardware expects that phys with different addresses will not form a wide
port unless the local peer phys also match each other.  Introduce a flag
to select stricter behavior at sas_register_ha() time.  The flag can be
dropped once it is known that all libsas users expect the same behavior.

Current drivers just initialize this field to zero and get the
traditional behavior.

Reported-by: Patrick Thomson 
Signed-off-by: Dan Williams 
Signed-off-by: James Bottomley

SCSI host lock push-down

2010-11-16T21:33:23+00:00

Move the mid-layer's ->queuecommand() invocation from being locked
with the host lock to being unlocked to facilitate speeding up the
critical path for drivers who don't need this lock taken anyway.

The patch below presents a simple SCSI host lock push-down as an
equivalent transformation.  No locking or other behavior should change
with this patch.  All existing bugs and locking orders are preserved.

Additionally, add one parameter to queuecommand,
	struct Scsi_Host *
and remove one parameter from queuecommand,
	void (*done)(struct scsi_cmnd *)

Scsi_Host* is a convenient pointer that most host drivers need anyway,
and 'done' is redundant to struct scsi_cmnd->scsi_done.

Minimal code disturbance was attempted with this change.  Most drivers
needed only two one-line modifications for their host lock push-down.

Signed-off-by: Jeff Garzik 
Acked-by: James Bottomley 
Signed-off-by: Linus Torvalds

[SCSI] libsas: Don't issue commands to devices that have been hot-removed

2010-10-08T21:03:42+00:00

sd will get hung up issuing commands to flush write cache if a SAS
device behind the expander is unplugged without warning.  Change libsas
to reject commands to domain devices that have already gone away.

[maciej.trela@intel.com: removed setting ->gone in sas_deform_port() to
 permit sync cache commands at module removal]

Signed-off-by: Darrick J. Wong 
Tested-by: Haipao Fan 
Signed-off-by: Maciej Trela 
Signed-off-by: Dan Williams 
Signed-off-by: James Bottomley

[SCSI] Unify SAM_ and SAM_STAT_ macros

2010-07-28T14:07:49+00:00

We have two separate definitions for identical constants with nearly the
same name.  One comes from the generic headers in scsi.h; the other is
an enum in libsas.h ... it's causing confusion about which one is
correct (fortunately they both are).

Fix this by eliminating the libsas.h duplicate

Signed-off-by: James Bottomley

include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

2010-03-30T13:02:32+00:00

percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.

Signed-off-by: Tejun Heo 
Guess-its-ok-by: Christoph Lameter 
Cc: Ingo Molnar 
Cc: Lee Schermerhorn

[SCSI] modify change_queue_depth to take in reason why it is being called

2009-12-04T18:00:41+00:00

This patch modifies scsi_host_template->change_queue_depth so that
it takes an argument indicating why it is being called. This will be
used so that if a LLD needs to do some extra processing when
handling queue fulls or later ramp ups, it can do so.

This is a simple port of the drivers setting a change_queue_depth
callback. In the patch I just have these LLDs adjust the queue depth
if the user was requesting it.

Signed-off-by: Mike Christie 

[Vasu.Dev: v2
	Also converted pmcraid_change_queue_depth and then verified
all modules compile  using "make allmodconfig" for any new build
warnings on X86_64.

	Updated original description after combing two original
patches from Mike to make this patch git bisectable.]
Signed-off-by: Vasu Dev 
[jejb: fixed up 53c700]
Signed-off-by: James Bottomley

include: Remove unnecessary inclusions of asm/semaphore.h

2008-04-19T02:16:54+00:00

None of these files use any of the functionality promised by
asm/semaphore.h.  It's possible that they (or some user of them) rely
on it dragging in some unrelated header file, but I can't build all
these files, so we'll have to fix any build failures as they come up.

Signed-off-by: Matthew Wilcox

[SCSI] libsas: Provide a transport-level facility to request SAS addrs

2008-04-07T17:15:38+00:00

Provide a facility to use the request_firmware() interface to get a SAS
address from userspace.  This can be used by SAS LLDDs that cannot
obtain the address from the host adapter.

Signed-off-by: Darrick J. Wong 
Signed-off-by: James Bottomley

[SCSI] libsas: export sas_find_local_phy function

2008-02-24T05:52:30+00:00

This is needed by the to be added I_T reset function in aic94xx.  It
needs to know the local phy so it can send a link or hard reset along
the path.

Signed-off-by: James Bottomley