linux-toradex.git/include/scsi/scsi_cmnd.h, branch v4.9.76

scsi: stop passing a gfp_mask argument down the command setup path

2014-11-24T18:56:55+00:00

There is no reason for ULDs to pass in a flag on how to allocate the S/G
lists.  While we don't need GFP_ATOMIC for the blk-mq case because we
don't hold locks, that decision can be made way down the chain without
having to pass a pointless gfp_mask argument.

Signed-off-by: Christoph Hellwig 
Reviewed-by: Bart Van Assche 
Reviewed-by: Hannes Reinecke

scsi: add new scsi-command flag for tagged commands

2014-11-12T10:19:40+00:00

Currently scsi piggy backs on the block layer to define the concept
of a tagged command.  But we want to be able to have block-level host-wide
tags assigned even for untagged commands like the initial INQUIRY, so add
a new SCSI-level flag for commands that are tagged at the scsi level, so
that even commands without that set can have tags assigned to them.  Note
that this alredy is the case for the blk-mq code path, and this just lets
the old path catch up with it.

We also set this flag based upon sdev->simple_tags instead of the block
queue flag, so that it is entirely independent of the block layer tagging,
and thus always correct even if a driver doesn't use block level tagging
yet.

Also remove the old blk_rq_tagged; it was only used by SCSI drivers, and
removing it forces them to look for the proper replacement.

Signed-off-by: Christoph Hellwig 
Reviewed-by: Mike Christie 
Reviewed-by: Martin K. Petersen 
Reviewed-by: Hannes Reinecke

sd: Honor block layer integrity handling flags

2014-09-30T21:17:35+00:00

A set of flags introduced in the block layer enable better control over
how protection information is handled. These flags are useful for both
error injection and data recovery purposes. Checking can be enabled and
disabled for controller and disk, and the guard tag format is now a
per-I/O property.

Update sd_protect_op to communicate the relevant information to the
low-level device driver via a set of flags in scsi_cmnd.

Signed-off-by: Martin K. Petersen 
Reviewed-by: Sagi Grimberg 
Acked-by: Christoph Hellwig 
Signed-off-by: Jens Axboe

scsi: remove various exports that were only used by scsi_tgt

2014-07-17T20:07:45+00:00

Signed-off-by: Christoph Hellwig 
Reviewed-by: Paolo Bonzini 
Reviewed-by: Hannes Reinecke

[SCSI] use the scsi data buffer length to extract transfer size

2014-07-03T17:50:31+00:00

Commit 8846bab180fa introduced a helper that can be used to query the
wire transfer size for a SCSI command taking protection information into
account.

However, some commands do not have a 1:1 mapping between the block range
they work on and the payload size (discard, write same). After the
scatterlist has been set up these requests use __data_len to store the
number of bytes to report completion on. This means that callers of
scsi_transfer_length() would get the wrong byte count for these types of
requests.

To overcome this we make scsi_transfer_length() use the scatterlist
length in the scsi_data_buffer as basis for the wire transfer
calculation instead of __data_len.

Reported-by: Christoph Hellwig 
Debugged-by: Mike Christie 
Signed-off-by: Martin K. Petersen 
Signed-off-by: Christoph Hellwig 
Reviewed-by: Sagi Grimberg 
Fixes: d77e65350f2d82dfa0557707d505711f5a43c8fd
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley

Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending

2014-06-13T05:38:32+00:00

Pull SCSI target updates from Nicholas Bellinger:
 "The highlights this round include:

   - Add support for T10 PI pass-through between vhost-scsi +
     virtio-scsi (MST + Paolo + MKP + nab)
   - Add support for T10 PI in qla2xxx target mode (Quinn + MKP + hch +
     nab, merged through scsi.git)
   - Add support for percpu-ida pre-allocation in qla2xxx target code
     (Quinn + nab)
   - A number of iser-target fixes related to hardening the network
     portal shutdown path (Sagi + Slava)
   - Fix response length residual handling for a number of control CDBs
     (Roland + Christophe V.)
   - Various iscsi RFC conformance fixes in the CHAP authentication path
     (Tejas and Calsoft folks + nab)
   - Return TASK_SET_FULL status for tcm_fc(FCoE) DataIn + Response
     failures (Vasu + Jun + nab)
   - Fix long-standing ABORT_TASK + session reset hang (nab)
   - Convert iser-initiator + iser-target to include T10 bytes into EDTL
     (Sagi + Or + MKP + Mike Christie)
   - Fix NULL pointer dereference regression related to XCOPY introduced
     in v3.15 + CC'ed to v3.12.y (nab)"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (34 commits)
  target: Fix NULL pointer dereference for XCOPY in target_put_sess_cmd
  vhost-scsi: Include prot_bytes into expected data transfer length
  TARGET/sbc,loopback: Adjust command data length in case pi exists on the wire
  libiscsi, iser: Adjust data_length to include protection information
  scsi_cmnd: Introduce scsi_transfer_length helper
  target: Report correct response length for some commands
  target/sbc: Check that the LBA and number of blocks are correct in VERIFY
  target/sbc: Remove sbc_check_valid_sectors()
  Target/iscsi: Fix sendtargets response pdu for iser transport
  Target/iser: Fix a wrong dereference in case discovery session is over iser
  iscsi-target: Fix ABORT_TASK + connection reset iscsi_queue_req memory leak
  target: Use complete_all for se_cmd->t_transport_stop_comp
  target: Set CMD_T_ACTIVE bit for Task Management Requests
  target: cleanup some boolean tests
  target/spc: Simplify INQUIRY EVPD=0x80
  tcm_fc: Generate TASK_SET_FULL status for response failures
  tcm_fc: Generate TASK_SET_FULL status for DataIN failures
  iscsi-target: Reject mutual authentication with reflected CHAP_C
  iscsi-target: Remove no-op from iscsit_tpg_del_portal_group
  iscsi-target: Fix CHAP_A parameter list handling
  ...

scsi_cmnd: Introduce scsi_transfer_length helper

2014-06-11T20:06:42+00:00

In case protection information exists on the wire
scsi transports should include it in the transfer
byte count (even if protection information does not
exist in the host memory space). This helper will
compute the total transfer length from the scsi
command data length and protection attributes.

Signed-off-by: Sagi Grimberg 
Signed-off-by: Martin K. Petersen 
Cc: stable@vger.kernel.org # 3.15+
Signed-off-by: Nicholas Bellinger

virtio_scsi: use cmd_size

2014-05-19T17:57:23+00:00

Taken almost entirely from Nicholas Bellinger's scsi-mq conversion.

Signed-off-by: Christoph Hellwig 
Acked-by: Paolo Bonzini 
Reviewed-by: Nicholas Bellinger

[SCSI] megaraid: simplify internal command handling

2014-03-27T15:26:31+00:00

We don't use the passed in scsi command for anything, so just add a adapter-
wide internal status to go along with the internal scb that is used unter
int_mtx to pass back the return value and get rid of all the complexities
and abuse of the scsi_cmnd structure.

This gets rid of the only user of scsi_allocate_command/scsi_free_command,
which can now be removed.

[jejb: checkpatch fixes]
Signed-off-by: Christoph Hellwig 
Acked-by: Adam Radford 
Signed-off-by: James Bottomley

[SCSI] do not manipulate device reference counts in scsi_get/put_command

2014-03-15T17:19:24+00:00

Many callers won't need this and we can optimize them away.  In addition
the handling in the __-prefixed variants was inconsistant to start with.

Based on an earlier patch from Bart Van Assche.

[jejb: fix kerneldoc probelm picked up by Fengguang Wu]
Signed-off-by: Christoph Hellwig 
Reviewed-by: Hannes Reinecke 
Signed-off-by: James Bottomley