ASoC: Fixes for v7.0 A moderately large pile of fixes, though none of them are super major, plus a few new quirks and device IDs.
Move the ASP register patches to a separate struct and apply this from the ASP DAI probe() function so that the registers are only patched if the DAI is part of a DAI link. Some systems use the ASP as a special-purpose interconnect and on these systems the ASP registers are configured by a third party (the firmware, the BIOS, or another device using the amp's secondary host control interface). If the machine driver does not hook up the ASP DAI then the ASP registers must be omitted from the patch to prevent overwriting the third party configuration. If the machine driver includes the ASP DAI in a DAI link, this implies that the machine driver and higher components (such as alsa-ucm) are taking ownership of the ASP. In this case the ASP registers are patched to known defaults and the machine driver should configure the ASP. Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Link: https://patch.msgid.link/20260226110137.1664562-1-rf@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org>
On TAS2781, if the Speaker calibrated impedance is lower than default value hard-coded inside the TAS2781, it will cuase vol lower than normal. In order to fix this issue, the parameter of SineGainI need updating. Signed-off-by: Shenghao Ding <shenghao-ding@ti.com> Tested-by: Matthew Schwartz <matthew.schwartz@linux.dev> Link: https://patch.msgid.link/20260227144641.1243-1-shenghao-ding@ti.com Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASoC: Updates for v7.0 This release is almost all abut driers, there's very little core work here, although some of that driver work is in more generic areas like SDCA and SOF: - Generic SDCA support for reporting jack events. - Continuing platform support, cleanup and feature improements for the AMD, Intel, Qualcomm and SOF code. - Platform description improvements for the Cirrus drivers. - Support for NXP i.MX952, Realtek RT1320 and RT5575, and Sophogo CV1800B. We also pulled in one small SPI API update and some more substantial regmap work (cache description improvements) for use in drivers.
Add support for using the state of pins on the amplifier to indicate the type of speaker fitted. Previously, where there were alternate speaker vendors, this was indicated using host CPU GPIOs. Some new Dell models use spare pins on the CS35L63 as GPIOs for the speaker ID detection. Cirrus-specific SDCA Disco properties provide a list of the pins to be used, and pull-up/down settings for the pads. This list is ordered, MSbit to LSbit. The code to set the firmware filename has been modified to check for using chip pins for speaker ID. The entire block of code to set firmware name has been moved out of cs35l56_component_probe() into its own function to make it easier to KUnit test. Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Link: https://patch.msgid.link/20260205164838.1611295-2-rf@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Charles Keepax <ckeepax@opensource.cirrus.com>: A bit of a mixed bag of minor misc fixes, improve handling of volatile SDCA Controls, make some minor bug fixes to jack detect, improve the cache syncing by adding some more defaults, and improve some FDL error messages.
Some of the SDCA Controls have a defined reset value in the specification. Update the parsing to add these specification defined values into the regmap defaults array. This will reduce the number of registers that are synchronised on a cache sync. Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://patch.msgid.link/20260204125944.1134011-6-ckeepax@opensource.cirrus.com Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.dev> Signed-off-by: Mark Brown <broonie@kernel.org>
TAS2781 driver supports three solutions of calibrated data. The first is from the driver itself: driver reads the calibrated files directly during probe; The second is from user space: during init of audio hal, the audio hal will pass the calibrated data via kcontrol interface. Driver will store this data in "struct calidata" for use. The third is from UEFI, mainly used in hda device. These three solutions save the calibrated data into different data structures. It is time to put them together into "struct calidata" for use. Signed-off-by: Shenghao Ding <shenghao-ding@ti.com> Link: https://patch.msgid.link/20260202102757.532-1-shenghao-ding@ti.com Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>: Now, all DAPM users are using function to handling it. We can capsuling it. This patchset moves struct snd_soc_dapm_context into soc-dapm.c, and remove un-used functions. Link: https://lore.kernel.org/r/87zf7jrx52.wl-kuninori.morimoto.gx@renesas.com
Merge series from "Peng Fan (OSS)" <peng.fan@oss.nxp.com>: The main goal is to convert drivers to use GPIO descriptors. While reading the code, I think it is time to remove ak4641 and pxa2xx-ac97 driver, more info could be found in commit log of each patch. Then only need to convert sound/arm/pxa2xx-ac97-lib.c to use GPIO descriptors. Not have hardware to test the pxa2xx ac97.