Jesse Gross says: ==================== A number of improvements for net-next/3.10. Highlights include: * Properly exposing linux/openvswitch.h to userspace after the uapi changes. * Simplification of locking. It immediately makes things simpler to reason about and avoids holding RTNL mutex for longer than necessary. In the near future it will also enable tunnel registration and more fine-grained locking. * Miscellaneous cleanups and simplifications. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces an UAPI header for the SCTP protocol, so that we can facilitate the maintenance and development of user land applications or libraries, in particular in terms of header synchronization. To not break compatibility, some fragments from lksctp-tools' netinet/sctp.h have been carefully included, while taking care that neither kernel nor user land breaks, so both compile fine with this change (for lksctp-tools I tested with the old netinet/sctp.h header and with a newly adapted one that includes the uapi sctp header). lksctp-tools smoke test run through successfully as well in both cases. Suggested-by: Neil Horman <nhorman@tuxdriver.com> Cc: Neil Horman <nhorman@tuxdriver.com> Cc: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
It contains the public netlink interface bits required by userspace to make use of the interface. Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com> Conflicts: fs/btrfs/disk-io.c
The header file will then be installed under /usr/include/linux so that userspace applications can refer to Btrfs ioctls by name and use the same structs used internally in the kernel. Signed-off-by: Filipe Brandenburger <filbranden@google.com> Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Pull networking changes from David Miller:
1) Allow to dump, monitor, and change the bridge multicast database
using netlink. From Cong Wang.
2) RFC 5961 TCP blind data injection attack mitigation, from Eric
Dumazet.
3) Networking user namespace support from Eric W. Biederman.
4) tuntap/virtio-net multiqueue support by Jason Wang.
5) Support for checksum offload of encapsulated packets (basically,
tunneled traffic can still be checksummed by HW). From Joseph
Gasparakis.
6) Allow BPF filter access to VLAN tags, from Eric Dumazet and
Daniel Borkmann.
7) Bridge port parameters over netlink and BPDU blocking support
from Stephen Hemminger.
8) Improve data access patterns during inet socket demux by rearranging
socket layout, from Eric Dumazet.
9) TIPC protocol updates and cleanups from Ying Xue, Paul Gortmaker, and
Jon Maloy.
10) Update TCP socket hash sizing to be more in line with current day
realities. The existing heurstics were choosen a decade ago.
From Eric Dumazet.
11) Fix races, queue bloat, and excessive wakeups in ATM and
associated drivers, from Krzysztof Mazur and David Woodhouse.
12) Support DOVE (Distributed Overlay Virtual Ethernet) extensions
in VXLAN driver, from David Stevens.
13) Add "oops_only" mode to netconsole, from Amerigo Wang.
14) Support set and query of VEB/VEPA bridge mode via PF_BRIDGE, also
allow DCB netlink to work on namespaces other than the initial
namespace. From John Fastabend.
15) Support PTP in the Tigon3 driver, from Matt Carlson.
16) tun/vhost zero copy fixes and improvements, plus turn it on
by default, from Michael S. Tsirkin.
17) Support per-association statistics in SCTP, from Michele
Baldessari.
And many, many, driver updates, cleanups, and improvements. Too
numerous to mention individually.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
net/mlx4_en: Add support for destination MAC in steering rules
net/mlx4_en: Use generic etherdevice.h functions.
net: ethtool: Add destination MAC address to flow steering API
bridge: add support of adding and deleting mdb entries
bridge: notify mdb changes via netlink
ndisc: Unexport ndisc_{build,send}_skb().
uapi: add missing netconf.h to export list
pkt_sched: avoid requeues if possible
solos-pci: fix double-free of TX skb in DMA mode
bnx2: Fix accidental reversions.
bna: Driver Version Updated to 3.1.2.1
bna: Firmware update
bna: Add RX State
bna: Rx Page Based Allocation
bna: TX Intr Coalescing Fix
bna: Tx and Rx Optimizations
bna: Code Cleanup and Enhancements
ath9k: check pdata variable before dereferencing it
ath5k: RX timestamp is reported at end of frame
ath9k_htc: RX timestamp is reported at end of frame
...
Add netconf.h for use by iproute2. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Make perf build for x86 once the UAPI disintegration patches for that arch have been applied by adding the appropriate -I flags - in the right order - and then converting some #includes that use ../.. notation to find main kernel headerfiles to use <asm/foo.h> and <linux/foo.h> instead. Note that -Iarch/foo/include/uapi is present _before_ -Iarch/foo/include. This makes sure we get the userspace version of the pt_regs struct. Ideally, we wouldn't have the latter -I flag at all, but unfortunately we want asm/svm.h and asm/vmx.h in builtin-kvm.c and these aren't part of the UAPI - at least not for x86. I wonder if the bits outside of the __KERNEL__ guards *should* be transferred there. I note also that perf seems to do its dependency handling manually by listing all the header files it might want to use in LIB_H in the Makefile. Can this be changed to use -MD? Note that to do make this work, we need to export and UAPI disintegrate linux/hw_breakpoint.h, which I think should've been exported previously so that perf can access the bits. We have to do this in the same patch to maintain bisectability. Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Michael Kerrisk <mtk.manpages@gmail.com> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Acked-by: Dave Jones <davej@redhat.com>
Plumb the UAPI Kbuilds into the user header installation and checking system.
As the headers are split the entries will be transferred across from the old
Kbuild files to the UAPI Kbuild files.
The changes made in this commit are:
(1) Exported generated files (of which there are currently four) are moved to
uapi/ directories under the appropriate generated/ directory, thus we
get:
include/generated/uapi/linux/version.h
arch/x86/include/generated/uapi/asm/unistd_32.h
arch/x86/include/generated/uapi/asm/unistd_64.h
arch/x86/include/generated/uapi/asm/unistd_x32.h
These paths were added to the build as -I flags in a previous patch.
(2) scripts/Makefile.headersinst is now given the UAPI path to install from
rather than the old path.
It then determines the old path from that and includes that Kbuild also
if it exists, thus permitting the headers to exist in either directory
during the changeover.
I also renamed the "install" variable to "installdir" as it refers to a
directory not the install program.
(3) scripts/headers_install.pl is altered to take a list of source file paths
instead of just their names so that the makefile can tell it exactly
where to find each file.
For the moment, files can be obtained from one of four places for each
output directory:
.../include/uapi/foo/
.../include/generated/uapi/foo/
.../include/foo/
.../include/generated/foo/
The non-UAPI paths will be dropped later.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>