linux-toradex.git/include/uapi/linux/devlink.h, branch v5.12-rc7

devlink: Support get and set state of port function

2021-01-22T19:32:08+00:00

devlink port function can be in active or inactive state.
Allow users to get and set port function's state.

When the port function it activated, its operational state may change
after a while when the device is created and driver binds to it.
Similarly on deactivation flow.

To clearly describe the state of the port function and its device's
operational state in the host system, define state and opstate
attributes.

Example of a PCI SF port which supports a port function:

$ devlink dev eswitch set pci/0000:06:00.0 mode switchdev

$ devlink port show
pci/0000:06:00.0/65535: type eth netdev ens2f0np0 flavour physical port 0 splittable false

$ devlink port add pci/0000:06:00.0 flavour pcisf pfnum 0 sfnum 88
pci/0000:08:00.0/32768: type eth netdev eth6 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
  function:
    hw_addr 00:00:00:00:00:00 state inactive opstate detached

$ devlink port show pci/0000:06:00.0/32768
pci/0000:06:00.0/32768: type eth netdev ens2f0npf0sf88 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
  function:
    hw_addr 00:00:00:00:88:88 state inactive opstate detached

$ devlink port function set pci/0000:06:00.0/32768 hw_addr 00:00:00:00:88:88 state active

$ devlink port show pci/0000:06:00.0/32768 -jp
{
    "port": {
        "pci/0000:06:00.0/32768": {
            "type": "eth",
            "netdev": "ens2f0npf0sf88",
            "flavour": "pcisf",
            "controller": 0,
            "pfnum": 0,
            "sfnum": 88,
            "external": false,
            "splittable": false,
            "function": {
                "hw_addr": "00:00:00:00:88:88",
                "state": "active",
                "opstate": "attached"
            }
        }
    }
}

Signed-off-by: Parav Pandit 
Reviewed-by: Jiri Pirko 
Reviewed-by: Vu Pham 
Signed-off-by: Saeed Mahameed

devlink: Introduce PCI SF port flavour and port attribute

2021-01-22T19:32:07+00:00

A PCI sub-function (SF) represents a portion of the device similar
to PCI VF.

In an eswitch, PCI SF may have port which is normally represented
using a representor netdevice.
To have better visibility of eswitch port, its association with SF,
and its representor netdevice, introduce a PCI SF port flavour.

When devlink port flavour is PCI SF, fill up PCI SF attributes of the
port.

Extend port name creation using PCI PF and SF number scheme on best
effort basis, so that vendor drivers can skip defining their own
scheme.
This is done as cApfNSfM, where A, N and M are controller, PCI PF and
PCI SF number respectively.
This is similar to existing naming for PCI PF and PCI VF ports.

An example view of a PCI SF port:

$ devlink port show pci/0000:06:00.0/32768
pci/0000:06:00.0/32768: type eth netdev ens2f0npf0sf88 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
  function:
    hw_addr 00:00:00:00:88:88 state active opstate attached

$ devlink port show pci/0000:06:00.0/32768 -jp
{
    "port": {
        "pci/0000:06:00.0/32768": {
            "type": "eth",
            "netdev": "ens2f0npf0sf88",
            "flavour": "pcisf",
            "controller": 0,
            "pfnum": 0,
            "sfnum": 88,
            "splittable": false,
            "function": {
                "hw_addr": "00:00:00:00:88:88",
                "state": "active",
                "opstate": "attached"
            }
        }
    }
}

Signed-off-by: Parav Pandit 
Reviewed-by: Jiri Pirko 
Reviewed-by: Vu Pham 
Signed-off-by: Saeed Mahameed

devlink: use _BITUL() macro instead of BIT() in the UAPI header

2020-12-17T00:16:40+00:00

The BIT() macro is not available for the UAPI headers. Moreover, it can
be defined differently in user space headers. Thus, replace its usage
with the _BITUL() macro which is already used in other macro definitions
in .

Fixes: dc64cc7c6310 ("devlink: Add devlink reload limit option")
Signed-off-by: Tobias Klauser 
Link: https://lore.kernel.org/r/20201215102531.16958-1-tklauser@distanz.ch
Signed-off-by: Jakub Kicinski

devlink: Fix reload stats structure

2020-11-24T21:04:04+00:00

Fix reload stats structure exposed to the user. Change stats structure
hierarchy to have the reload action as a parent of the stat entry and
then stat entry includes value per limit. This will also help to avoid
string concatenation on iproute2 output.

Reload stats structure before this fix:
"stats": {
    "reload": {
        "driver_reinit": 2,
        "fw_activate": 1,
        "fw_activate_no_reset": 0
     }
}

After this fix:
"stats": {
    "reload": {
        "driver_reinit": {
            "unspecified": 2
        },
        "fw_activate": {
            "unspecified": 1,
            "no_reset": 0
        }
}

Fixes: a254c264267e ("devlink: Add reload stats")
Signed-off-by: Moshe Shemesh 
Reviewed-by: Jiri Pirko 
Link: https://lore.kernel.org/r/1606109785-25197-1-git-send-email-moshe@mellanox.com
Signed-off-by: Jakub Kicinski

devlink: Add remote reload stats

2020-10-09T19:06:52+00:00

Add remote reload stats to hold the history of actions performed due
devlink reload commands initiated by remote host. For example, in case
firmware activation with reset finished successfully but was initiated
by remote host.

The function devlink_remote_reload_actions_performed() is exported to
enable drivers update on remote reload actions performed as it was not
initiated by their own devlink instance.

Expose devlink remote reload stats to the user through devlink dev get
command.

Examples:
$ devlink dev show
pci/0000:82:00.0:
  stats:
      reload:
        driver_reinit 2 fw_activate 1 fw_activate_no_reset 0
      remote_reload:
        driver_reinit 0 fw_activate 0 fw_activate_no_reset 0
pci/0000:82:00.1:
  stats:
      reload:
        driver_reinit 1 fw_activate 0 fw_activate_no_reset 0
      remote_reload:
        driver_reinit 1 fw_activate 1 fw_activate_no_reset 0

$ devlink dev show -jp
{
    "dev": {
        "pci/0000:82:00.0": {
            "stats": {
                "reload": {
                    "driver_reinit": 2,
                    "fw_activate": 1,
                    "fw_activate_no_reset": 0
                },
                "remote_reload": {
                    "driver_reinit": 0,
                    "fw_activate": 0,
                    "fw_activate_no_reset": 0
                }
            }
        },
        "pci/0000:82:00.1": {
            "stats": {
                "reload": {
                    "driver_reinit": 1,
                    "fw_activate": 0,
                    "fw_activate_no_reset": 0
                },
                "remote_reload": {
                    "driver_reinit": 1,
                    "fw_activate": 1,
                    "fw_activate_no_reset": 0
                }
            }
        }
    }
}

Signed-off-by: Moshe Shemesh 
Reviewed-by: Jakub Kicinski 
Reviewed-by: Jiri Pirko 
Signed-off-by: Jakub Kicinski

devlink: Add reload stats

2020-10-09T19:06:52+00:00

Add reload stats to hold the history per reload action type and limit.

For example, the number of times fw_activate has been performed on this
device since the driver module was added or if the firmware activation
was performed with or without reset.

Add devlink notification on stats update.

Expose devlink reload stats to the user through devlink dev get command.

Examples:
$ devlink dev show
pci/0000:82:00.0:
  stats:
      reload:
        driver_reinit 2 fw_activate 1 fw_activate_no_reset 0
pci/0000:82:00.1:
  stats:
      reload:
        driver_reinit 1 fw_activate 0 fw_activate_no_reset 0

$ devlink dev show -jp
{
    "dev": {
        "pci/0000:82:00.0": {
            "stats": {
                "reload": {
                    "driver_reinit": 2,
                    "fw_activate": 1,
                    "fw_activate_no_reset": 0
                }
            }
        },
        "pci/0000:82:00.1": {
            "stats": {
                "reload": {
                    "driver_reinit": 1,
                    "fw_activate": 0,
                    "fw_activate_no_reset": 0
                }
            }
        }
    }
}

Signed-off-by: Moshe Shemesh 
Reviewed-by: Jiri Pirko 
Signed-off-by: Jakub Kicinski

devlink: Add devlink reload limit option

2020-10-09T19:06:52+00:00

Add reload limit to demand restrictions on reload actions.
Reload limits supported:
no_reset: No reset allowed, no down time allowed, no link flap and no
          configuration is lost.

By default reload limit is unspecified and so no constraints on reload
actions are required.

Some combinations of action and limit are invalid. For example, driver
can not reinitialize its entities without any downtime.

The no_reset reload limit will have usecase in this patchset to
implement restricted fw_activate on mlx5.

Have the uapi parameter of reload limit ready for future support of
multiselection.

Signed-off-by: Moshe Shemesh 
Reviewed-by: Jiri Pirko 
Signed-off-by: Jakub Kicinski

devlink: Add reload action option to devlink reload command

2020-10-09T19:06:52+00:00

Add devlink reload action to allow the user to request a specific reload
action. The action parameter is optional, if not specified then devlink
driver re-init action is used (backward compatible).
Note that when required to do firmware activation some drivers may need
to reload the driver. On the other hand some drivers may need to reset
the firmware to reinitialize the driver entities. Therefore, the devlink
reload command returns the actions which were actually performed.
Reload actions supported are:
driver_reinit: driver entities re-initialization, applying devlink-param
               and devlink-resource values.
fw_activate: firmware activate.

command examples:
$devlink dev reload pci/0000:82:00.0 action driver_reinit
reload_actions_performed:
  driver_reinit

$devlink dev reload pci/0000:82:00.0 action fw_activate
reload_actions_performed:
  driver_reinit fw_activate

Signed-off-by: Moshe Shemesh 
Reviewed-by: Jakub Kicinski 
Reviewed-by: Jacob Keller 
Reviewed-by: Jiri Pirko 
Signed-off-by: Jakub Kicinski

net: devlink: Add unused port flavour

2020-10-04T21:38:52+00:00

Not all ports of a switch need to be used, particularly in embedded
systems. Add a port flavour for ports which physically exist in the
switch, but are not connected to the front panel etc, and so are
unused. By having unused ports present in devlink, it gives a more
accurate representation of the hardware. It also allows regions to be
associated to such ports, so allowing, for example, to determine
unused ports are correctly powered off, or to compare probable reset
defaults of unused ports to used ports experiences issues.

Actually registering unused ports and setting the flavour to unused is
optional. The DSA core will register all such switch ports, but such
ports are expected to be limited in number. Bigger ASICs may decide
not to list unused ports.

v2:
Expand the description about why it is useful

Reviewed-by: Vladimir Oltean 
Tested-by: Vladimir Oltean 
Signed-off-by: Andrew Lunn 
Reviewed-by: Florian Fainelli 
Signed-off-by: David S. Miller

devlink: include for _BITUL

2020-09-29T20:58:41+00:00

Commit 5d5b4128c4ca ("devlink: introduce flash update overwrite mask")
added a usage of _BITUL to the UAPI  header, but failed
to include the header file where it was defined. It happens that this
does not break any existing kernel include chains because it gets
included through other sources. However, when including the UAPI headers
in a userspace application (such as devlink in iproute2), _BITUL is not
defined.

Fixes: 5d5b4128c4ca ("devlink: introduce flash update overwrite mask")
Signed-off-by: Jacob Keller 
Signed-off-by: David S. Miller