Allow optionally specifying the link ID to transmit on,
which can be done instead of the link frequency, on an
MLD addressed frame. Both can also be omitted in which
case the frame must be MLD addressed and link selection
(and address translation) will be done on lower layers.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add attributes for reporting hardware timestamps for management frames
RX and TX. These attributes will be used for reporting hardware
timestamps for Timing measurement and Fine Timing Measurement action
frames, which will allow userspace applications to measure the path
delay between devices and sync clocks.

For TX, these attributes are used for reporting the frame RX time and
the ack TX time. For TX, they are used for reporting the frame TX time
and the ack RX time.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Clarify the link ID behaviour in control port TX, we need it
to select the link to transmit on for both MLD and non-MLD
receivers, but select the link address as the SA only if the
receiver is not an MLD.

Fixes: 67207bab9341 ("wifi: cfg80211/mac80211: Support control port TX from specific link")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

We have the per-interface type capabilities, currently for
extended capabilities, add the EML/MLD capabilities there
to have this advertised by the driver.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add an API for adding/modifying/removing a link of a station.

Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

commit dd374f84baec ("wifi: nl80211: expose link ID for associated
BSSes") used a top-level attribute to send link ID of the associated
BSS in the nested attribute NL80211_ATTR_BSS. But since NL80211_ATTR_BSS
is a nested attribute of the attributes defined in enum nl80211_bss,
define a new attribute in enum nl80211_bss and use it for sending the
link ID of the BSS.

Fixes: dd374f84baec ("wifi: nl80211: expose link ID for associated BSSes")
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20220708122607.1836958-1-quic_vjakkam@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Increase akm_suites array size in struct cfg80211_crypto_settings to 10
and advertise the capability to userspace. This allows userspace to send
more than two AKMs to driver in netlink commands such as
NL80211_CMD_CONNECT.

This capability is needed for implementing WPA3-Personal transition mode
correctly with any driver that handles roaming internally. Currently,
the possible AKMs for multi-AKM connect can include PSK, PSK-SHA-256,
SAE, FT-PSK and FT-SAE. Since the count is already 5, increasing
the akm_suites array size to 10 should be reasonable for future
usecases.

Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Link: https://lore.kernel.org/r/1653312358-12321-1-git-send-email-quic_vjakkam@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The MLO links used for connection with an MLD AP are decided by the
driver in case of SME offloaded to driver.

Add support for the drivers to indicate the information of links used
for MLO connection in connect and roam callbacks, update the connected
links information in wdev from connect/roam result sent by driver.
Also, send the connected links information to userspace.

Add a netlink flag attribute to indicate that userspace supports
handling of MLO connection. Drivers must not do MLO connection when this
flag is not set. This is to maintain backwards compatibility with older
supplicant versions which doesn't have support for MLO connection.

Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

For authentication, we need the BSS, the link_id and the AP
MLD address to create the link and station, (for now) the
driver assigns a link address and sends the frame, the MLD
address needs to be the address of the interface.

For association, pass the list of BSSes that were selected
for the MLO connection, along with extra per-STA profile
elements, the AP MLD address and the link ID on which the
association request should be sent.

Note that for now we don't have a proper way to pass the link
address(es) and so the driver/mac80211 will select one, but
depending on how that selection works it means that assoc w/o
auth data still being around (mac80211 implementation detail)
the association won't necessarily work - so this will need to
be extended in the future to sort out the link addressing.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In order to support multi-link operation with multiple links,
start adding some APIs. The notable addition here is to have
the link ID in a new nl80211 attribute, that will be used to
differentiate the links in many nl80211 operations.

So far, this patch adds the netlink NL80211_ATTR_MLO_LINK_ID
attribute (as well as the NL80211_ATTR_MLO_LINKS attribute)
and plugs it through the system in some places, checking the
validity etc. along with other infrastructure needed for it.

For now, I've decided to include only the over-the-air link
ID in the API. I know we discussed that we eventually need to
have to have other ways of identifying a link, but for local
AP mode and auth/assoc commands as well as set_key etc. we'll
use the OTA ID.

Also included in this patch is some refactoring of the data
structures in struct wireless_dev, splitting for the first
time the data into type dependent pieces, to make reasoning
about these things easier.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>