linux-toradex.git/kernel/power, branch v6.9-rc5 Linux kernel for Apalis and Colibri modules PM: s2idle: Make sure CPUs will wakeup directly on resume 2024-04-08T13:36:54+00:00 Anna-Maria Behnsen anna-maria@linutronix.de 2024-04-08T07:02:23+00:00 3c89a068bfd0698a5478f4cf39493595ef757d5e s2idle works like a regular suspend with freezing processes and freezing devices. All CPUs except the control CPU go into idle. Once this is completed the control CPU kicks all other CPUs out of idle, so that they reenter the idle loop and then enter s2idle state. The control CPU then issues an swait() on the suspend state and therefore enters the idle loop as well. Due to being kicked out of idle, the other CPUs leave their NOHZ states, which means the tick is active and the corresponding hrtimer is programmed to the next jiffie. On entering s2idle the CPUs shut down their local clockevent device to prevent wakeups. The last CPU which enters s2idle shuts down its local clockevent and freezes timekeeping. On resume, one of the CPUs receives the wakeup interrupt, unfreezes timekeeping and its local clockevent and starts the resume process. At that point all other CPUs are still in s2idle with their clockevents switched off. They only resume when they are kicked by another CPU or after resuming devices and then receiving a device interrupt. That means there is no guarantee that all CPUs will wakeup directly on resume. As a consequence there is no guarantee that timers which are queued on those CPUs and should expire directly after resume, are handled. Also timer list timers which are remotely queued to one of those CPUs after resume will not result in a reprogramming IPI as the tick is active. Queueing a hrtimer will also not result in a reprogramming IPI because the first hrtimer event is already in the past. The recent introduction of the timer pull model (7ee988770326 ("timers: Implement the hierarchical pull model")) amplifies this problem, if the current migrator is one of the non woken up CPUs. When a non pinned timer list timer is queued and the queuing CPU goes idle, it relies on the still suspended migrator CPU to expire the timer which will happen by chance. The problem exists since commit 8d89835b0467 ("PM: suspend: Do not pause cpuidle in the suspend-to-idle path"). There the cpuidle_pause() call which in turn invoked a wakeup for all idle CPUs was moved to a later point in the resume process. This might not be reached or reached very late because it waits on a timer of a still suspended CPU. Address this by kicking all CPUs out of idle after the control CPU returns from swait() so that they resume their timers and restore consistent system state. Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218641 Fixes: 8d89835b0467 ("PM: suspend: Do not pause cpuidle in the suspend-to-idle path") Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Mario Limonciello <mario.limonciello@amd.com> Cc: 5.16+ <stable@kernel.org> # 5.16+ Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> 
s2idle works like a regular suspend with freezing processes and freezing
devices. All CPUs except the control CPU go into idle. Once this is
completed the control CPU kicks all other CPUs out of idle, so that they
reenter the idle loop and then enter s2idle state. The control CPU then
issues an swait() on the suspend state and therefore enters the idle loop
as well.

Due to being kicked out of idle, the other CPUs leave their NOHZ states,
which means the tick is active and the corresponding hrtimer is programmed
to the next jiffie.

On entering s2idle the CPUs shut down their local clockevent device to
prevent wakeups. The last CPU which enters s2idle shuts down its local
clockevent and freezes timekeeping.

On resume, one of the CPUs receives the wakeup interrupt, unfreezes
timekeeping and its local clockevent and starts the resume process. At that
point all other CPUs are still in s2idle with their clockevents switched
off. They only resume when they are kicked by another CPU or after resuming
devices and then receiving a device interrupt.

That means there is no guarantee that all CPUs will wakeup directly on
resume. As a consequence there is no guarantee that timers which are queued
on those CPUs and should expire directly after resume, are handled. Also
timer list timers which are remotely queued to one of those CPUs after
resume will not result in a reprogramming IPI as the tick is
active. Queueing a hrtimer will also not result in a reprogramming IPI
because the first hrtimer event is already in the past.

The recent introduction of the timer pull model (7ee988770326 ("timers:
Implement the hierarchical pull model")) amplifies this problem, if the
current migrator is one of the non woken up CPUs. When a non pinned timer
list timer is queued and the queuing CPU goes idle, it relies on the still
suspended migrator CPU to expire the timer which will happen by chance.

The problem exists since commit 8d89835b0467 ("PM: suspend: Do not pause
cpuidle in the suspend-to-idle path"). There the cpuidle_pause() call which
in turn invoked a wakeup for all idle CPUs was moved to a later point in
the resume process. This might not be reached or reached very late because
it waits on a timer of a still suspended CPU.

Address this by kicking all CPUs out of idle after the control CPU returns
from swait() so that they resume their timers and restore consistent system
state.

Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218641
Fixes: 8d89835b0467 ("PM: suspend: Do not pause cpuidle in the suspend-to-idle path")
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Mario Limonciello <mario.limonciello@amd.com>
Cc: 5.16+ <stable@kernel.org> # 5.16+
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge tag 'rtc-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux 2024-03-22T00:16:46+00:00 Linus Torvalds torvalds@linux-foundation.org 2024-03-22T00:16:46+00:00 3faae16b5aaed284c7de6f4c12240da67497d3a3 Pull RTC updates from Alexandre Belloni: "Subsytem: - rtc_class is now const Drivers: - ds1511: cleanup, set date and time range and alarm offset limit - max31335: fix interrupt handler - pcf8523: improve suspend support" * tag 'rtc-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (28 commits) MAINTAINER: Include linux-arm-msm for Qualcomm RTC patches dt-bindings: rtc: zynqmp: Add support for Versal/Versal NET SoCs rtc: class: make rtc_class constant dt-bindings: rtc: abx80x: Improve checks on trickle charger constraints MAINTAINERS: adjust file entry in ARM/Mediatek RTC DRIVER rtc: nct3018y: fix possible NULL dereference rtc: max31335: fix interrupt status reg rtc: mt6397: select IRQ_DOMAIN instead of depending on it dt-bindings: rtc: abx80x: convert to yaml rtc: m41t80: Use the unified property API get the wakeup-source property dt-bindings: at91rm9260-rtt: add sam9x7 compatible dt-bindings: rtc: convert MT7622 RTC to the json-schema dt-bindings: rtc: convert MT2717 RTC to the json-schema rtc: pcf8523: add suspend handlers for alarm IRQ rtc: ds1511: set alarm offset limit rtc: ds1511: set range rtc: ds1511: drop inline/noinline hints rtc: ds1511: rename pdata rtc: ds1511: implement ds1511_rtc_read_alarm properly rtc: ds1511: remove partial alarm support ... 
Pull RTC updates from Alexandre Belloni:
 "Subsytem:
   - rtc_class is now const

  Drivers:
   - ds1511: cleanup, set date and time range and alarm offset limit
   - max31335: fix interrupt handler
   - pcf8523: improve suspend support"

* tag 'rtc-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (28 commits)
  MAINTAINER: Include linux-arm-msm for Qualcomm RTC patches
  dt-bindings: rtc: zynqmp: Add support for Versal/Versal NET SoCs
  rtc: class: make rtc_class constant
  dt-bindings: rtc: abx80x: Improve checks on trickle charger constraints
  MAINTAINERS: adjust file entry in ARM/Mediatek RTC DRIVER
  rtc: nct3018y: fix possible NULL dereference
  rtc: max31335: fix interrupt status reg
  rtc: mt6397: select IRQ_DOMAIN instead of depending on it
  dt-bindings: rtc: abx80x: convert to yaml
  rtc: m41t80: Use the unified property API get the wakeup-source property
  dt-bindings: at91rm9260-rtt: add sam9x7 compatible
  dt-bindings: rtc: convert MT7622 RTC to the json-schema
  dt-bindings: rtc: convert MT2717 RTC to the json-schema
  rtc: pcf8523: add suspend handlers for alarm IRQ
  rtc: ds1511: set alarm offset limit
  rtc: ds1511: set range
  rtc: ds1511: drop inline/noinline hints
  rtc: ds1511: rename pdata
  rtc: ds1511: implement ds1511_rtc_read_alarm properly
  rtc: ds1511: remove partial alarm support
  ...
PM: EM: Force device drivers to provide power in uW 2024-03-13T19:48:38+00:00 Lukasz Luba lukasz.luba@arm.com 2024-03-08T12:32:03+00:00 3acec69a94eaaf3d7ebb043e1db45cc26f58a847 The EM only supports power in uW. Make sure that it is not possible to register some downstream driver which doesn't provide power in uW. The only exception is artificial EM, but that EM is ignored by the rest of kernel frameworks (thermal, powercap, etc). Reported-by: PoShao Chen <poshao.chen@mediatek.com> Signed-off-by: Lukasz Luba <lukasz.luba@arm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> 
The EM only supports power in uW. Make sure that it is not possible to
register some downstream driver which doesn't provide power in uW.
The only exception is artificial EM, but that EM is ignored by the rest of
kernel frameworks (thermal, powercap, etc).

Reported-by: PoShao Chen <poshao.chen@mediatek.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge tag 'pm-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm 2024-03-13T18:40:06+00:00 Linus Torvalds torvalds@linux-foundation.org 2024-03-13T18:40:06+00:00 07abb19a9b201c11e4367e8a428be7235b6dbd0d Pull power management updates from Rafael Wysocki: "From the functional perspective, the most significant change here is the addition of support for Energy Models that can be updated dynamically at run time. There is also the addition of LZ4 compression support for hibernation, the new preferred core support in amd-pstate, new platforms support in the Intel RAPL driver, new model-specific EPP handling in intel_pstate and more. Apart from that, the cpufreq default transition delay is reduced from 10 ms to 2 ms (along with some related adjustments), the system suspend statistics code undergoes a significant rework and there is a usual bunch of fixes and code cleanups all over. Specifics: - Allow the Energy Model to be updated dynamically (Lukasz Luba) - Add support for LZ4 compression algorithm to the hibernation image creation and loading code (Nikhil V) - Fix and clean up system suspend statistics collection (Rafael Wysocki) - Simplify device suspend and resume handling in the power management core code (Rafael Wysocki) - Fix PCI hibernation support description (Yiwei Lin) - Make hibernation take set_memory_ro() return values into account as appropriate (Christophe Leroy) - Set mem_sleep_current during kernel command line setup to avoid an ordering issue with handling it (Maulik Shah) - Fix wake IRQs handling when pm_runtime_force_suspend() is used as a driver's system suspend callback (Qingliang Li) - Simplify pm_runtime_get_if_active() usage and add a replacement for pm_runtime_put_autosuspend() (Sakari Ailus) - Add a tracepoint for runtime_status changes tracking (Vilas Bhat) - Fix section title markdown in the runtime PM documentation (Yiwei Lin) - Enable preferred core support in the amd-pstate cpufreq driver (Meng Li) - Fix min_perf assignment in amd_pstate_adjust_perf() and make the min/max limit perf values in amd-pstate always stay within the (highest perf, lowest perf) range (Tor Vic, Meng Li) - Allow intel_pstate to assign model-specific values to strings used in the EPP sysfs interface and make it do so on Meteor Lake (Srinivas Pandruvada) - Drop long-unused cpudata::prev_cummulative_iowait from the intel_pstate cpufreq driver (Jiri Slaby) - Prevent scaling_cur_freq from exceeding scaling_max_freq when the latter is an inefficient frequency (Shivnandan Kumar) - Change default transition delay in cpufreq to 2ms (Qais Yousef) - Remove references to 10ms minimum sampling rate from comments in the cpufreq code (Pierre Gondois) - Honour transition_latency over transition_delay_us in cpufreq (Qais Yousef) - Stop unregistering cpufreq cooling on CPU hot-remove (Viresh Kumar) - General enhancements / cleanups to ARM cpufreq drivers (tianyu2, Nícolas F. R. A. Prado, Erick Archer, Arnd Bergmann, Anastasia Belova) - Update cpufreq-dt-platdev to block/approve devices (Richard Acayan) - Make the SCMI cpufreq driver get a transition delay value from firmware (Pierre Gondois) - Prevent the haltpoll cpuidle governor from shrinking guest poll_limit_ns below grow_start (Parshuram Sangle) - Avoid potential overflow in integer multiplication when computing cpuidle state parameters (C Cheng) - Adjust MWAIT hint target C-state computation in the ACPI cpuidle driver and in intel_idle to return a correct value for C0 (He Rongguang) - Address multiple issues in the TPMI RAPL driver and add support for new platforms (Lunar Lake-M, Arrow Lake) to Intel RAPL (Zhang Rui) - Fix freq_qos_add_request() return value check in dtpm_cpu (Daniel Lezcano) - Fix kernel-doc for dtpm_create_hierarchy() (Yang Li) - Fix file leak in get_pkg_num() in x86_energy_perf_policy (Samasth Norway Ananda) - Fix cpupower-frequency-info.1 man page typo (Jan Kratochvil) - Fix a couple of warnings in the OPP core code related to W=1 builds (Viresh Kumar) - Move dev_pm_opp_{init|free}_cpufreq_table() to pm_opp.h (Viresh Kumar) - Extend dev_pm_opp_data with turbo support (Sibi Sankar) - dt-bindings: drop maxItems from inner items (David Heidelberg)" * tag 'pm-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (95 commits) dt-bindings: opp: drop maxItems from inner items OPP: debugfs: Fix warning around icc_get_name() OPP: debugfs: Fix warning with W=1 builds cpufreq: Move dev_pm_opp_{init|free}_cpufreq_table() to pm_opp.h OPP: Extend dev_pm_opp_data with turbo support Fix cpupower-frequency-info.1 man page typo cpufreq: scmi: Set transition_delay_us firmware: arm_scmi: Populate fast channel rate_limit firmware: arm_scmi: Populate perf commands rate_limit cpuidle: ACPI/intel: fix MWAIT hint target C-state computation PM: sleep: wakeirq: fix wake irq warning in system suspend powercap: dtpm: Fix kernel-doc for dtpm_create_hierarchy() function cpufreq: Don't unregister cpufreq cooling on CPU hotplug PM: suspend: Set mem_sleep_current during kernel command line setup cpufreq: Honour transition_latency over transition_delay_us cpufreq: Limit resolving a frequency to policy min/max Documentation: PM: Fix runtime_pm.rst markdown syntax cpufreq: amd-pstate: adjust min/max limit perf cpufreq: Remove references to 10ms min sampling rate cpufreq: intel_pstate: Update default EPPs for Meteor Lake ... 
Pull power management updates from Rafael Wysocki:
 "From the functional perspective, the most significant change here is
  the addition of support for Energy Models that can be updated
  dynamically at run time.

  There is also the addition of LZ4 compression support for hibernation,
  the new preferred core support in amd-pstate, new platforms support in
  the Intel RAPL driver, new model-specific EPP handling in intel_pstate
  and more.

  Apart from that, the cpufreq default transition delay is reduced from
  10 ms to 2 ms (along with some related adjustments), the system
  suspend statistics code undergoes a significant rework and there is a
  usual bunch of fixes and code cleanups all over.

  Specifics:

   - Allow the Energy Model to be updated dynamically (Lukasz Luba)

   - Add support for LZ4 compression algorithm to the hibernation image
     creation and loading code (Nikhil V)

   - Fix and clean up system suspend statistics collection (Rafael
     Wysocki)

   - Simplify device suspend and resume handling in the power management
     core code (Rafael Wysocki)

   - Fix PCI hibernation support description (Yiwei Lin)

   - Make hibernation take set_memory_ro() return values into account as
     appropriate (Christophe Leroy)

   - Set mem_sleep_current during kernel command line setup to avoid an
     ordering issue with handling it (Maulik Shah)

   - Fix wake IRQs handling when pm_runtime_force_suspend() is used as a
     driver's system suspend callback (Qingliang Li)

   - Simplify pm_runtime_get_if_active() usage and add a replacement for
     pm_runtime_put_autosuspend() (Sakari Ailus)

   - Add a tracepoint for runtime_status changes tracking (Vilas Bhat)

   - Fix section title markdown in the runtime PM documentation (Yiwei
     Lin)

   - Enable preferred core support in the amd-pstate cpufreq driver
     (Meng Li)

   - Fix min_perf assignment in amd_pstate_adjust_perf() and make the
     min/max limit perf values in amd-pstate always stay within the
     (highest perf, lowest perf) range (Tor Vic, Meng Li)

   - Allow intel_pstate to assign model-specific values to strings used
     in the EPP sysfs interface and make it do so on Meteor Lake
     (Srinivas Pandruvada)

   - Drop long-unused cpudata::prev_cummulative_iowait from the
     intel_pstate cpufreq driver (Jiri Slaby)

   - Prevent scaling_cur_freq from exceeding scaling_max_freq when the
     latter is an inefficient frequency (Shivnandan Kumar)

   - Change default transition delay in cpufreq to 2ms (Qais Yousef)

   - Remove references to 10ms minimum sampling rate from comments in
     the cpufreq code (Pierre Gondois)

   - Honour transition_latency over transition_delay_us in cpufreq (Qais
     Yousef)

   - Stop unregistering cpufreq cooling on CPU hot-remove (Viresh Kumar)

   - General enhancements / cleanups to ARM cpufreq drivers (tianyu2,
     Nícolas F. R. A. Prado, Erick Archer, Arnd Bergmann, Anastasia
     Belova)

   - Update cpufreq-dt-platdev to block/approve devices (Richard Acayan)

   - Make the SCMI cpufreq driver get a transition delay value from
     firmware (Pierre Gondois)

   - Prevent the haltpoll cpuidle governor from shrinking guest
     poll_limit_ns below grow_start (Parshuram Sangle)

   - Avoid potential overflow in integer multiplication when computing
     cpuidle state parameters (C Cheng)

   - Adjust MWAIT hint target C-state computation in the ACPI cpuidle
     driver and in intel_idle to return a correct value for C0 (He
     Rongguang)

   - Address multiple issues in the TPMI RAPL driver and add support for
     new platforms (Lunar Lake-M, Arrow Lake) to Intel RAPL (Zhang Rui)

   - Fix freq_qos_add_request() return value check in dtpm_cpu (Daniel
     Lezcano)

   - Fix kernel-doc for dtpm_create_hierarchy() (Yang Li)

   - Fix file leak in get_pkg_num() in x86_energy_perf_policy (Samasth
     Norway Ananda)

   - Fix cpupower-frequency-info.1 man page typo (Jan Kratochvil)

   - Fix a couple of warnings in the OPP core code related to W=1 builds
     (Viresh Kumar)

   - Move dev_pm_opp_{init|free}_cpufreq_table() to pm_opp.h (Viresh
     Kumar)

   - Extend dev_pm_opp_data with turbo support (Sibi Sankar)

   - dt-bindings: drop maxItems from inner items (David Heidelberg)"

* tag 'pm-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (95 commits)
  dt-bindings: opp: drop maxItems from inner items
  OPP: debugfs: Fix warning around icc_get_name()
  OPP: debugfs: Fix warning with W=1 builds
  cpufreq: Move dev_pm_opp_{init|free}_cpufreq_table() to pm_opp.h
  OPP: Extend dev_pm_opp_data with turbo support
  Fix cpupower-frequency-info.1 man page typo
  cpufreq: scmi: Set transition_delay_us
  firmware: arm_scmi: Populate fast channel rate_limit
  firmware: arm_scmi: Populate perf commands rate_limit
  cpuidle: ACPI/intel: fix MWAIT hint target C-state computation
  PM: sleep: wakeirq: fix wake irq warning in system suspend
  powercap: dtpm: Fix kernel-doc for dtpm_create_hierarchy() function
  cpufreq: Don't unregister cpufreq cooling on CPU hotplug
  PM: suspend: Set mem_sleep_current during kernel command line setup
  cpufreq: Honour transition_latency over transition_delay_us
  cpufreq: Limit resolving a frequency to policy min/max
  Documentation: PM: Fix runtime_pm.rst markdown syntax
  cpufreq: amd-pstate: adjust min/max limit perf
  cpufreq: Remove references to 10ms min sampling rate
  cpufreq: intel_pstate: Update default EPPs for Meteor Lake
  ...
Merge branch 'pm-em' 2024-03-11T14:59:51+00:00 Rafael J. Wysocki rafael.j.wysocki@intel.com 2024-03-11T14:59:51+00:00 3bd834640baa1e220a79e27d2033e2ef3a29124a Merge Enery Model changes for 6.9-rc1: - Allow the Energy Model to be updated dynamically (Lukasz Luba). * pm-em: (24 commits) PM: EM: Fix nr_states warnings in static checks Documentation: EM: Update with runtime modification design PM: EM: Add em_dev_compute_costs() PM: EM: Remove old table PM: EM: Change debugfs configuration to use runtime EM table data drivers/thermal/devfreq_cooling: Use new Energy Model interface drivers/thermal/cpufreq_cooling: Use new Energy Model interface powercap/dtpm_devfreq: Use new Energy Model interface to get table powercap/dtpm_cpu: Use new Energy Model interface to get table PM: EM: Optimize em_cpu_energy() and remove division PM: EM: Support late CPUs booting and capacity adjustment PM: EM: Add performance field to struct em_perf_state and optimize PM: EM: Add em_perf_state_from_pd() to get performance states table PM: EM: Introduce em_dev_update_perf_domain() for EM updates PM: EM: Add functions for memory allocations for new EM tables PM: EM: Use runtime modified EM for CPUs energy estimation in EAS PM: EM: Introduce runtime modifiable table PM: EM: Split the allocation and initialization of the EM table PM: EM: Check if the get_cost() callback is present in em_compute_costs() PM: EM: Introduce em_compute_costs() ... 
Merge Enery Model changes for 6.9-rc1:

 - Allow the Energy Model to be updated dynamically (Lukasz Luba).

* pm-em: (24 commits)
  PM: EM: Fix nr_states warnings in static checks
  Documentation: EM: Update with runtime modification design
  PM: EM: Add em_dev_compute_costs()
  PM: EM: Remove old table
  PM: EM: Change debugfs configuration to use runtime EM table data
  drivers/thermal/devfreq_cooling: Use new Energy Model interface
  drivers/thermal/cpufreq_cooling: Use new Energy Model interface
  powercap/dtpm_devfreq: Use new Energy Model interface to get table
  powercap/dtpm_cpu: Use new Energy Model interface to get table
  PM: EM: Optimize em_cpu_energy() and remove division
  PM: EM: Support late CPUs booting and capacity adjustment
  PM: EM: Add performance field to struct em_perf_state and optimize
  PM: EM: Add em_perf_state_from_pd() to get performance states table
  PM: EM: Introduce em_dev_update_perf_domain() for EM updates
  PM: EM: Add functions for memory allocations for new EM tables
  PM: EM: Use runtime modified EM for CPUs energy estimation in EAS
  PM: EM: Introduce runtime modifiable table
  PM: EM: Split the allocation and initialization of the EM table
  PM: EM: Check if the get_cost() callback is present in em_compute_costs()
  PM: EM: Introduce em_compute_costs()
  ...
rtc: class: make rtc_class constant 2024-03-08T11:05:10+00:00 Ricardo B. Marliere ricardo@marliere.net 2024-03-05T18:22:28+00:00 6b6ca096115e5b7a85e8313f4e68a72d52db91b3 Since commit 43a7206b0963 ("driver core: class: make class_register() take a const *"), the driver core allows for struct class to be in read-only memory, so move the rtc_class structure to be declared at build time placing it into read-only memory, instead of having to be dynamically allocated at boot time. Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net> Link: https://lore.kernel.org/r/20240305-class_cleanup-abelloni-v1-1-944c026137c8@marliere.net Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> 
Since commit 43a7206b0963 ("driver core: class: make class_register() take
a const *"), the driver core allows for struct class to be in read-only
memory, so move the rtc_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at boot time.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Link: https://lore.kernel.org/r/20240305-class_cleanup-abelloni-v1-1-944c026137c8@marliere.net
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
PM: suspend: Set mem_sleep_current during kernel command line setup 2024-02-29T19:33:00+00:00 Maulik Shah quic_mkshah@quicinc.com 2024-02-29T06:44:59+00:00 9bc4ffd32ef8943f5c5a42c9637cfd04771d021b psci_init_system_suspend() invokes suspend_set_ops() very early during bootup even before kernel command line for mem_sleep_default is setup. This leads to kernel command line mem_sleep_default=s2idle not working as mem_sleep_current gets changed to deep via suspend_set_ops() and never changes back to s2idle. Set mem_sleep_current along with mem_sleep_default during kernel command line setup as default suspend mode. Fixes: faf7ec4a92c0 ("drivers: firmware: psci: add system suspend support") CC: stable@vger.kernel.org # 5.4+ Signed-off-by: Maulik Shah <quic_mkshah@quicinc.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> 
psci_init_system_suspend() invokes suspend_set_ops() very early during
bootup even before kernel command line for mem_sleep_default is setup.
This leads to kernel command line mem_sleep_default=s2idle not working
as mem_sleep_current gets changed to deep via suspend_set_ops() and never
changes back to s2idle.

Set mem_sleep_current along with mem_sleep_default during kernel command
line setup as default suspend mode.

Fixes: faf7ec4a92c0 ("drivers: firmware: psci: add system suspend support")
CC: stable@vger.kernel.org # 5.4+
Signed-off-by: Maulik Shah <quic_mkshah@quicinc.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
power: port block device access to file 2024-02-25T11:05:22+00:00 Christian Brauner brauner@kernel.org 2024-01-23T13:26:23+00:00 4379f91172f39d999919c8e8b2b5e1d665d8972d Link: https://lore.kernel.org/r/20240123-vfs-bdev-file-v2-6-adbd023e19cc@kernel.org Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Christian Brauner <brauner@kernel.org> 
Link: https://lore.kernel.org/r/20240123-vfs-bdev-file-v2-6-adbd023e19cc@kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Christian Brauner <brauner@kernel.org>
PM: EM: Fix nr_states warnings in static checks 2024-02-22T19:24:20+00:00 Lukasz Luba lukasz.luba@arm.com 2024-02-21T14:25:50+00:00 3a561ea2413ea5a740f3b1d6b5355d46f88a7456 During the static checks nr_states has been mentioned by the kernel test robot. Fix the warning in those 2 places. Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Lukasz Luba <lukasz.luba@arm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> 
During the static checks nr_states has been mentioned by the kernel test
robot. Fix the warning in those 2 places.

Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
PM: hibernate: Don't ignore return from set_memory_ro() 2024-02-22T19:08:03+00:00 Christophe Leroy christophe.leroy@csgroup.eu 2024-02-18T08:40:58+00:00 f4311756a83fb01c28a9bf841cbb7eb2b318eebf set_memory_ro() and set_memory_rw() can fail, leaving memory unprotected. Take the returned value into account and abort in case of failure. Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> 
set_memory_ro() and set_memory_rw() can fail, leaving memory
unprotected.

Take the returned value into account and abort in case of
failure.

Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>