This patch is basically a backport of
commit ee8a1a0a1a5817accd03ced7e7ffde3a4430f485 upstream
which was made after the big HID overhaul in 2.6.28.

Kernel 2.6.27 fails to handle quirks for the aluminum Apple Wireless
Keyboard because it is handled as USB device and not as Bluetooth
device. This patch expands 'hidp_blacklist' to make the kernel handle
the keyboard in the same way as the Apple wireless Mighty Mouse (also a
Bluetooth device).

Signed-off-by: Torsten Rausche <torsten@rausche.net>
Cc: Jan Scholz <Scholz@fias.uni-frankfurt.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

To speed up the Simple Pairing connection setup, the support for the
default link policy has been enabled. This is in contrast to settings
the link policy on every connection setup. Using the default link policy
is the preferred way since there is no need to dynamically change it for
every connection.

For backward compatibility reason and to support old userspace the
HCISETLINKPOL ioctl has been switched over to using hci_request() to
issue the HCI command for setting the default link policy instead of
just storing it in the HCI device structure.

However the hci_request() can only be issued when the device is
brought up. If used on a device that is registered, but still down
it will timeout and fail. This is problematic since the command is
put on the TX queue and the Bluetooth core tries to submit it to
hardware that is not ready yet. The timeout for these requests is
10 seconds and this causes a significant regression when setting up
a new device.

The userspace can perfectly handle a failure of the HCISETLINKPOL
ioctl and will re-submit it later, but the 10 seconds delay causes
a problem. So in case hci_request() is called on a device that is
still down, just fail it with ENETDOWN to indicate what happens.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The Security Mode 4 of the Bluetooth 2.1 specification has strict
authentication and encryption requirements. It is the initiators job
to create a secure ACL link. However in case of malicious devices, the
acceptor has to make sure that the ACL is encrypted before allowing
any kind of L2CAP connection. The only exception here is the PSM 1 for
the service discovery protocol, because that is allowed to run on an
insecure ACL link.

Previously it was enough to reject a L2CAP connection during the
connection setup phase, but with Bluetooth 2.1 it is forbidden to
do any L2CAP protocol exchange on an insecure link (except SDP).

The new hci_conn_check_link_mode() function can be used to check the
integrity of an ACL link. This functions also takes care of the cases
where Security Mode 4 is disabled or one of the devices is based on
an older specification.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

With the introduction of Security Mode 4 and Simple Pairing from the
Bluetooth 2.1 specification it became mandatory that the initiator
requires authentication and encryption before any L2CAP channel can
be established. The only exception here is PSM 1 for the service
discovery protocol (SDP). It is meant to be used without any encryption
since it contains only public information. This is how Bluetooth 2.0
and before handle connections on PSM 1.

For Bluetooth 2.1 devices the pairing procedure differentiates between
no bonding, general bonding and dedicated bonding. The L2CAP layer
wrongly uses always general bonding when creating new connections, but it
should not do this for SDP connections. In this case the authentication
requirement should be no bonding and the just-works model should be used,
but in case of non-SDP connection it is required to use general bonding.

If the new connection requires man-in-the-middle (MITM) protection, it
also first wrongly creates an unauthenticated link key and then later on
requests an upgrade to an authenticated link key to provide full MITM
protection. With Simple Pairing the link key generation is an expensive
operation (compared to Bluetooth 2.0 and before) and doing this twice
during a connection setup causes a noticeable delay when establishing
a new connection. This should be avoided to not regress from the expected
Bluetooth 2.0 connection times. The authentication requirements are known
up-front and so enforce them.

To fulfill these requirements the hci_connect() function has been extended
with an authentication requirement parameter that will be stored inside
the connection information and can be retrieved by userspace at any
time. This allows the correct IO capabilities exchange and results in
the expected behavior.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The ACL config stage keeps holding a reference count on incoming
connections when requesting the extended features. This results in
keeping an ACL link up without any users. The problem here is that
the Bluetooth specification doesn't define an ownership of the ACL
link and thus it can happen that the implementation on the initiator
side doesn't care about disconnecting unused links. In this case the
acceptor needs to take care of this.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The Bluetooth entries for the MAINTAINERS file are a little bit too
much. Consolidate them into two entries. One for Bluetooth drivers and
another one for the Bluetooth subsystem.

Also the MODULE_AUTHOR should indicate the current maintainer of the
module and actually not the original author. Fix all Bluetooth modules
to provide current maintainer information.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The Bluetooth adapters and connections are best presented via a class
in sysfs. The removal of the links inside the Bluetooth class broke
assumptions by userspace programs on how to find attached adapters.

This patch creates adapters and connections as part of the Bluetooth
class, but it uses different device types to distinguish them. The
userspace programs can now easily navigate in the sysfs device tree.

The unused platform device and bus have been removed to keep the
code simple and clean.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The Bluetooth qualification for PAN demands testing with BNEP header
compression disabled. This is actually pretty stupid and the Linux
implementation outsmarts the test system since it compresses whenever
possible. So to pass qualification two need parameters have been added
to control the compression of source and destination headers.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Don't create symlinks in a class to a device that is not owned by the
class.  If the bluetooth subsystem really wants to point to all of the
devices it controls, it needs to create real devices, not fake symlinks.

Cc: Maxim Krasnyansky <maxk@qualcomm.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (1232 commits)
  iucv: Fix bad merging.
  net_sched: Add size table for qdiscs
  net_sched: Add accessor function for packet length for qdiscs
  net_sched: Add qdisc_enqueue wrapper
  highmem: Export totalhigh_pages.
  ipv6 mcast: Omit redundant address family checks in ip6_mc_source().
  net: Use standard structures for generic socket address structures.
  ipv6 netns: Make several "global" sysctl variables namespace aware.
  netns: Use net_eq() to compare net-namespaces for optimization.
  ipv6: remove unused macros from net/ipv6.h
  ipv6: remove unused parameter from ip6_ra_control
  tcp: fix kernel panic with listening_get_next
  tcp: Remove redundant checks when setting eff_sacks
  tcp: options clean up
  tcp: Fix MD5 signatures for non-linear skbs
  sctp: Update sctp global memory limit allocations.
  sctp: remove unnecessary byteshifting, calculate directly in big-endian
  sctp: Allow only 1 listening socket with SO_REUSEADDR
  sctp: Do not leak memory on multiple listen() calls
  sctp: Support ipv6only AF_INET6 sockets.
  ...