linux-toradex.git/net/bluetooth, branch v2.6.28.9

net: Fix module refcount leak in kernel_accept()

2008-12-19T03:35:10+00:00

The kernel_accept() does not hold the module refcount of newsock->ops->owner,
so we need __module_get(newsock->ops->owner) code after call kernel_accept()
by hand.
In sunrpc, the module refcount is missing to hold. So this cause kernel panic.

Used following script to reproduct:

while [ 1 ];
do
    mount -t nfs4 192.168.0.19:/ /mnt
    touch /mnt/file
    umount /mnt
    lsmod | grep ipv6
done

This patch fixed the problem by add __module_get(newsock->ops->owner) to
kernel_accept(). So we do not need to used __module_get(newsock->ops->owner)
in every place when used kernel_accept().

Signed-off-by: Wei Yongjun 
Signed-off-by: David S. Miller

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6

2008-10-17T15:58:52+00:00

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  net: Remove CONFIG_KMOD from net/ (towards removing CONFIG_KMOD entirely)
  ipv4: Add a missing rcu_assign_pointer() in routing cache.
  [netdrvr] ibmtr: PCMCIA IBMTR is ok on 64bit
  xen-netfront: Avoid unaligned accesses to IP header
  lmc: copy_*_user under spinlock
  [netdrvr] myri10ge, ixgbe: remove broken select INTEL_IOATDMA

net: Remove CONFIG_KMOD from net/ (towards removing CONFIG_KMOD entirely)

2008-10-16T22:24:51+00:00

Some code here depends on CONFIG_KMOD to not try to load
protocol modules or similar, replace by CONFIG_MODULES
where more than just request_module depends on CONFIG_KMOD
and and also use try_then_request_module in ebtables.

Signed-off-by: Johannes Berg 
Signed-off-by: Rusty Russell 
Signed-off-by: David S. Miller

HID: move connect quirks

2008-10-14T21:50:56+00:00

Move connecting from usbhid to the hid layer and fix also hidp in
that manner.
This removes all the ignore/force hidinput/hiddev connecting quirks.

Signed-off-by: Jiri Slaby 
Signed-off-by: Jiri Kosina

HID: move apple quirks

2008-10-14T21:50:49+00:00

Move them from the core code to a separate driver.

Signed-off-by: Jiri Slaby 
Signed-off-by: Jiri Kosina

HID: move ignore quirks

2008-10-14T21:50:49+00:00

Move ignore quirks from usbhid-quirks into hid-core code. Also don't output
warning when ENODEV is error code in usbhid and try ordinal input in hidp
when that error is returned.

Signed-off-by: Jiri Slaby 
Signed-off-by: Jiri Kosina

HID: hid, make parsing event driven

2008-10-14T21:50:48+00:00

Next step for complete hid bus, this patch includes:
- call parser either from probe or from hid-core if there is no probe.
- add ll_driver structure and centralize some stuff there (open, close...)
- split and merge usb_hid_configure and hid_probe into several functions
  to allow hooks/fixes between them

Signed-off-by: Jiri Slaby 
Signed-off-by: Jiri Kosina

HID: make a bus from hid code

2008-10-14T21:50:48+00:00

Make a bus from hid core. This is the first step for converting all the
quirks and separate almost-drivers into real drivers attached to this bus.

It's implemented to change behaviour in very tiny manner, so that no driver
needs to be changed this time.

Also add generic drivers for both usb and bt into usbhid or hidp
respectively which will bind all non-blacklisted device. Those blacklisted
will be either grabbed by special drivers or by nobody if they are broken at
the very rude base.

Signed-off-by: Jiri Slaby 
Signed-off-by: Jiri Kosina

[Bluetooth] Fix regression from using default link policy

2008-09-12T01:11:54+00:00

To speed up the Simple Pairing connection setup, the support for the
default link policy has been enabled. This is in contrast to settings
the link policy on every connection setup. Using the default link policy
is the preferred way since there is no need to dynamically change it for
every connection.

For backward compatibility reason and to support old userspace the
HCISETLINKPOL ioctl has been switched over to using hci_request() to
issue the HCI command for setting the default link policy instead of
just storing it in the HCI device structure.

However the hci_request() can only be issued when the device is
brought up. If used on a device that is registered, but still down
it will timeout and fail. This is problematic since the command is
put on the TX queue and the Bluetooth core tries to submit it to
hardware that is not ready yet. The timeout for these requests is
10 seconds and this causes a significant regression when setting up
a new device.

The userspace can perfectly handle a failure of the HCISETLINKPOL
ioctl and will re-submit it later, but the 10 seconds delay causes
a problem. So in case hci_request() is called on a device that is
still down, just fail it with ENETDOWN to indicate what happens.

Signed-off-by: Marcel Holtmann

[Bluetooth] Reject L2CAP connections on an insecure ACL link

2008-09-09T05:19:20+00:00

The Security Mode 4 of the Bluetooth 2.1 specification has strict
authentication and encryption requirements. It is the initiators job
to create a secure ACL link. However in case of malicious devices, the
acceptor has to make sure that the ACL is encrypted before allowing
any kind of L2CAP connection. The only exception here is the PSM 1 for
the service discovery protocol, because that is allowed to run on an
insecure ACL link.

Previously it was enough to reject a L2CAP connection during the
connection setup phase, but with Bluetooth 2.1 it is forbidden to
do any L2CAP protocol exchange on an insecure link (except SDP).

The new hci_conn_check_link_mode() function can be used to check the
integrity of an ACL link. This functions also takes care of the cases
where Security Mode 4 is disabled or one of the devices is based on
an older specification.

Signed-off-by: Marcel Holtmann