This patch fixes CUBIC so that cwnd reductions made during RTOs can be
undone (just as they already can be undone when using the default/Reno
behavior).

When undoing cwnd reductions, BIC-derived congestion control modules
were restoring the cwnd from last_max_cwnd. There were two problems
with using last_max_cwnd to restore a cwnd during undo:

(a) last_max_cwnd was set to 0 on state transitions into TCP_CA_Loss
(by calling the module's reset() functions), so cwnd reductions from
RTOs could not be undone.

(b) when fast_covergence is enabled (which it is by default)
last_max_cwnd does not actually hold the value of snd_cwnd before the
loss; instead, it holds a scaled-down version of snd_cwnd.

This patch makes the following changes:

(1) upon undo, revert snd_cwnd to ca->loss_cwnd, which is already, as
the existing comment notes, the "congestion window at last loss"

(2) stop forgetting ca->loss_cwnd on TCP_CA_Loss events

(3) use ca->last_max_cwnd to check if we're in slow start

Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Sangtae Ha <sangtae.ha@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TCP Cubic keeps a metric that estimates the amount of delayed
acknowledgements to use in adjusting the window. If an abnormally
large number of packets are acknowledged at once, then the update
could wrap and reach zero. This kind of ACK could only
happen when there was a large window and huge number of
ACK's were lost.

This patch limits the value of delayed ack ratio. The choice of 32
is just a conservative value since normally it should be range of
1 to 4 packets.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

HyStart sets the initial exit point of slow start.
Suppose that HyStart exits at 0.5BDP in a BDP network and no history exists.
If the BDP of a network is large, CUBIC's initial cwnd growth may be
too conservative to utilize the link.
CUBIC increases the cwnd 20% per RTT in this case.

Signed-off-by: Sangtae Ha <sangtae.ha@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make HyStart less sensitive to abrupt delay variations due to buffer bloat.

Signed-off-by: Sangtae Ha <sangtae.ha@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Reported-by: Lucas Nussbaum <lucas.nussbaum@loria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a refined version of an earlier patch by Lucas Nussbaum.
Cubic needs RTT values in milliseconds. If HZ < 1000 then
the values will be too coarse.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reported-by: Lucas Nussbaum <lucas.nussbaum@loria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

The hystart code was written with assumption that HZ=1000.
Replace the use of jiffies with bictcp_clock as a millisecond
real time clock.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reported-by: Lucas Nussbaum <lucas.nussbaum@loria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make the spacing between ACK's that indicates a train a tuneable
value like other hystart values.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiffies wraps around therefore the correct way to compare is
to use cast to signed value.

Note: cubic is not using full jiffies value on 64 bit arch
because using full unsigned long makes struct bictcp grow too
large for the available ca_priv area.

Includes correction from Sangtae Ha to improve ack train detection.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>