linux-toradex.git/net/ipv6/af_inet6.c, branch toradex_5.2.y

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 152

2019-05-30T18:26:32+00:00

Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 of the license or at
  your option any later version

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 3029 file(s).

Signed-off-by: Thomas Gleixner 
Reviewed-by: Allison Randal 
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman

net: rework SIOCGSTAMP ioctl handling

2019-04-19T21:07:40+00:00

The SIOCGSTAMP/SIOCGSTAMPNS ioctl commands are implemented by many
socket protocol handlers, and all of those end up calling the same
sock_get_timestamp()/sock_get_timestampns() helper functions, which
results in a lot of duplicate code.

With the introduction of 64-bit time_t on 32-bit architectures, this
gets worse, as we then need four different ioctl commands in each
socket protocol implementation.

To simplify that, let's add a new .gettstamp() operation in
struct proto_ops, and move ioctl implementation into the common
sock_ioctl()/compat_sock_ioctl_trans() functions that these all go
through.

We can reuse the sock_get_timestamp() implementation, but generalize
it so it can deal with both native and compat mode, as well as
timeval and timespec structures.

Acked-by: Stefan Schmidt 
Acked-by: Neil Horman 
Acked-by: Marc Kleine-Budde 
Link: https://lore.kernel.org/lkml/CAK8P3a038aDQQotzua_QtKGhq8O9n+rdiz2=WDCp82ys8eUT+A@mail.gmail.com/
Signed-off-by: Arnd Bergmann 
Acked-by: Willem de Bruijn 
Signed-off-by: David S. Miller

ipv6: Add rate limit mask for ICMPv6 messages

2019-04-18T23:58:37+00:00

To make ICMPv6 closer to ICMPv4, add ratemask parameter. Since the ICMP
message types use larger numeric values, a simple bitmask doesn't fit.
I use large bitmap. The input and output are the in form of list of
ranges. Set the default to rate limit all error messages but Packet Too
Big. For Packet Too Big, use ratemask instead of hard-coded.

There are functions where icmpv6_xrlim_allow() and icmpv6_global_allow()
aren't called. This patch only adds them to icmpv6_echo_reply().

Rate limiting error messages is mandated by RFC 4443 but RFC 4890 says
that it is also acceptable to rate limit informational messages. Thus,
I removed the current hard-coded behavior of icmpv6_mask_allow() that
doesn't rate limit informational messages.

v2: Add dummy function proc_do_large_bitmap() if CONFIG_PROC_SYSCTL
    isn't defined, expand the description in ip-sysctl.txt and remove
    unnecessary conditional before kfree().
v3: Inline the bitmap instead of dynamically allocated. Still is a
    pointer to it is needed because of the way proc_do_large_bitmap work.

Signed-off-by: Stephen Suryaputra 
Signed-off-by: David S. Miller

ipv6: Rename fib6_multipath_select and pass fib6_result

2019-04-18T06:08:51+00:00

Add 'struct fib6_result' to hold the fib entry and fib6_nh from a fib
lookup as separate entries, similar to what IPv4 now has with fib_result.

Rename fib6_multipath_select to fib6_select_path, pass fib6_result to
it, and set f6i and nh in the result once a path selection is done.
Call fib6_select_path unconditionally for path selection which means
moving the sibling and oif check to fib6_select_path. To handle the two
different call paths (2 only call multipath_select if flowi6_oif == 0 and
the other always calls it), add a new have_oif_match that controls the
sibling walk if relevant.

Update callers of fib6_multipath_select accordingly and have them use the
fib6_info and fib6_nh from the result.

This is needed for multipath nexthop objects where a single f6i can
point to multiple fib6_nh (similar to IPv4).

Signed-off-by: David Ahern 
Signed-off-by: David S. Miller

ipv6: Add fib6_nh_init and release to stubs

2019-04-08T22:22:40+00:00

Add fib6_nh_init and fib6_nh_release to ipv6_stubs. If fib6_nh_init fails,
callers should not invoke fib6_nh_release, so there is no reason to have
a dummy stub for the IPv6 is not enabled case.

Signed-off-by: David Ahern 
Reviewed-by: Ido Schimmel 
Signed-off-by: David S. Miller

ipv6: Move ipv6 stubs to a separate header file

2019-03-29T17:53:45+00:00

The number of stubs is growing and has nothing to do with addrconf.
Move the definition of the stubs to a separate header file and update
users. In the move, drop the vxlan specific comment before ipv6_stub.

Code move only; no functional change intended.

Signed-off-by: David Ahern 
Signed-off-by: David S. Miller

ipv6: Add icmp_echo_ignore_anycast for ICMPv6

2019-03-20T23:29:37+00:00

In addition to icmp_echo_ignore_multicast, there is a need to also
prevent responding to pings to anycast addresses for security.

Signed-off-by: Stephen Suryaputra 
Signed-off-by: David S. Miller

ipv6: Add icmp_echo_ignore_multicast support for ICMPv6

2019-03-19T21:29:51+00:00

IPv4 has icmp_echo_ignore_broadcast to prevent responding to broadcast pings.
IPv6 needs a similar mechanism.

v1->v2:
- Remove NET_IPV6_ICMP_ECHO_IGNORE_MULTICAST.

Signed-off-by: Stephen Suryaputra 
Signed-off-by: David S. Miller

ipv6_stub: add ipv6_route_input stub/proxy.

2019-02-14T02:27:55+00:00

Proxy ip6_route_input via ipv6_stub, for later use by lwt bpf ip encap
(see the next patch in the patchset).

Signed-off-by: Peter Oskolkov 
Signed-off-by: Alexei Starovoitov

ipv6: Take rcu_read_lock in __inet6_bind for mapped addresses

2019-01-05T22:17:07+00:00

I realized the last patch calls dev_get_by_index_rcu in a branch not
holding the rcu lock. Add the calls to rcu_read_lock and rcu_read_unlock.

Fixes: ec90ad334986 ("ipv6: Consider sk_bound_dev_if when binding a socket to a v4 mapped address")
Signed-off-by: David Ahern 
Signed-off-by: David S. Miller