linux-toradex.git/net/sched/Makefile, branch v4.10

net sched ife action: Introduce skb tcindex metadata encap decap

2016-09-20T01:55:28+00:00

Sample use case of how this is encoded:
user space via tuntap (or a connected VM/Machine/container)
encodes the tcindex TLV.

Sample use case of decoding:
IFE action decodes it and the skb->tc_index is then used to classify.
So something like this for encoded ICMP packets:

.. first decode then reclassify... skb->tcindex will be set
sudo $TC filter add dev $ETH parent ffff: prio 2 protocol 0xbeef \
u32 match u32 0 0 flowid 1:1 \
action ife decode reclassify

...next match the decode icmp packet...
sudo $TC filter add dev $ETH parent ffff: prio 4 protocol ip \
u32 match ip protocol 1 0xff flowid 1:1 \
action continue

... last classify it using the tcindex classifier and do someaction..
sudo $TC filter add dev $ETH parent ffff: prio 5 protocol ip \
handle 0x11 tcindex classid 1:1 \
action blah..

Signed-off-by: Jamal Hadi Salim 
Signed-off-by: David S. Miller

net_sched: Introduce skbmod action

2016-09-15T23:33:47+00:00

This action is intended to be an upgrade from a usability perspective
from pedit (as well as operational debugability).
Compare this:

sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \
u32 match ip protocol 1 0xff flowid 1:2 \
action pedit munge offset -14 u8 set 0x02 \
munge offset -13 u8 set 0x15 \
munge offset -12 u8 set 0x15 \
munge offset -11 u8 set 0x15 \
munge offset -10 u16 set 0x1515 \
pipe

to:

sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \
u32 match ip protocol 1 0xff flowid 1:2 \
action skbmod dmac 02:15:15:15:15:15

Also try to do a MAC address swap with pedit or worse
try to debug a policy with destination mac, source mac and
etherype. Then make few rules out of those and you'll get my point.

In the future common use cases on pedit can be migrated to this action
(as an example different fields in ip v4/6, transports like tcp/udp/sctp
etc). For this first cut, this allows modifying basic ethernet header.

The most important ethernet use case at the moment is when redirecting or
mirroring packets to a remote machine. The dst mac address needs a re-write
so that it doesnt get dropped or confuse an interconnecting (learning) switch
or dropped by a target machine (which looks at the dst mac). And at times
when flipping back the packet a swap of the MAC addresses is needed.

Signed-off-by: Jamal Hadi Salim 
Signed-off-by: David S. Miller

net/sched: Introduce act_tunnel_key

2016-09-11T03:53:56+00:00

This action could be used before redirecting packets to a shared tunnel
device, or when redirecting packets arriving from a such a device.

The action will release the metadata created by the tunnel device
(decap), or set the metadata with the specified values for encap
operation.

For example, the following flower filter will forward all ICMP packets
destined to 11.11.11.2 through the shared vxlan device 'vxlan0'. Before
redirecting, a metadata for the vxlan tunnel is created using the
tunnel_key action and it's arguments:

$ tc filter add dev net0 protocol ip parent ffff: \
    flower \
      ip_proto 1 \
      dst_ip 11.11.11.2 \
    action tunnel_key set \
      src_ip 11.11.0.1 \
      dst_ip 11.11.0.2 \
      id 11 \
    action mirred egress redirect dev vxlan0

Signed-off-by: Amir Vadai 
Signed-off-by: Hadar Hen Zion 
Reviewed-by: Shmulik Ladkani 
Acked-by: Jamal Hadi Salim 
Acked-by: Eric Dumazet 
Signed-off-by: David S. Miller

net/sched: introduce Match-all classifier

2016-07-25T06:11:59+00:00

The matchall classifier matches every packet and allows the user to apply
actions on it. This filter is very useful in usecases where every packet
should be matched, for example, packet mirroring (SPAN) can be setup very
easily using that filter.

Signed-off-by: Jiri Pirko 
Signed-off-by: Yotam Gigi 
Signed-off-by: David S. Miller

Support to encoding decoding skb prio on IFE action

2016-03-01T22:15:23+00:00

    Example usage:
    Set the skb priority using skbedit then allow it to be encoded

    sudo tc qdisc add dev $ETH root handle 1: prio
    sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \
    u32 match ip protocol 1 0xff flowid 1:2 \
    action skbedit prio 17 \
    action ife encode \
    allow prio \
    dst 02:15:15:15:15:15

    Note: You dont need the skbedit action if you are already encoding the
    skb priority earlier. A zero skb priority will not be sent

    Alternative hard code static priority of decimal 33 (unlike skbedit)
    then mark of 0x12 every time the filter matches

    sudo $TC filter add dev $ETH parent 1: protocol ip prio 10 \
    u32 match ip protocol 1 0xff flowid 1:2 \
    action ife encode \
    type 0xDEAD \
    use prio 33 \
    use mark 0x12 \
    dst 02:15:15:15:15:15

    Signed-off-by: Jamal Hadi Salim 
Acked-by: Cong Wang 

Signed-off-by: David S. Miller

Support to encoding decoding skb mark on IFE action

2016-03-01T22:15:23+00:00

Example usage:
Set the skb using skbedit then allow it to be encoded

sudo tc qdisc add dev $ETH root handle 1: prio
sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \
u32 match ip protocol 1 0xff flowid 1:2 \
action skbedit mark 17 \
action ife encode \
allow mark \
dst 02:15:15:15:15:15

Note: You dont need the skbedit action if you are already encoding the
skb mark earlier. A zero skb mark, when seen, will not be encoded.

Alternative hard code static mark of 0x12 every time the filter matches

sudo $TC filter add dev $ETH parent 1: protocol ip prio 10 \
u32 match ip protocol 1 0xff flowid 1:2 \
action ife encode \
type 0xDEAD \
use mark 0x12 \
dst 02:15:15:15:15:15

Signed-off-by: Jamal Hadi Salim 
Acked-by: Cong Wang 
Signed-off-by: David S. Miller

introduce IFE action

2016-03-01T22:15:22+00:00

This action allows for a sending side to encapsulate arbitrary metadata
which is decapsulated by the receiving end.
The sender runs in encoding mode and the receiver in decode mode.
Both sender and receiver must specify the same ethertype.
At some point we hope to have a registered ethertype and we'll
then provide a default so the user doesnt have to specify it.
For now we enforce the user specify it.

Lets show example usage where we encode icmp from a sender towards
a receiver with an skbmark of 17; both sender and receiver use
ethertype of 0xdead to interop.

YYYY: Lets start with Receiver-side policy config:
xxx: add an ingress qdisc
sudo tc qdisc add dev $ETH ingress

xxx: any packets with ethertype 0xdead will be subjected to ife decoding
xxx: we then restart the classification so we can match on icmp at prio 3
sudo $TC filter add dev $ETH parent ffff: prio 2 protocol 0xdead \
u32 match u32 0 0 flowid 1:1 \
action ife decode reclassify

xxx: on restarting the classification from above if it was an icmp
xxx: packet, then match it here and continue to the next rule at prio 4
xxx: which will match based on skb mark of 17
sudo tc filter add dev $ETH parent ffff: prio 3 protocol ip \
u32 match ip protocol 1 0xff flowid 1:1 \
action continue

xxx: match on skbmark of 0x11 (decimal 17) and accept
sudo tc filter add dev $ETH parent ffff: prio 4 protocol ip \
handle 0x11 fw flowid 1:1 \
action ok

xxx: Lets show the decoding policy
sudo tc -s filter ls dev $ETH parent ffff: protocol 0xdead
xxx:
filter pref 2 u32
filter pref 2 u32 fh 800: ht divisor 1
filter pref 2 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:1  (rule hit 0 success 0)
  match 00000000/00000000 at 0 (success 0 )
        action order 1: ife decode action reclassify
         index 1 ref 1 bind 1 installed 14 sec used 14 sec
         type: 0x0
         Metadata: allow mark allow hash allow prio allow qmap
        Action statistics:
        Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
        backlog 0b 0p requeues 0
xxx:
Observe that above lists all metadatum it can decode. Typically these
submodules will already be compiled into a monolithic kernel or
loaded as modules

YYYY: Lets show the sender side now ..

xxx: Add an egress qdisc on the sender netdev
sudo tc qdisc add dev $ETH root handle 1: prio
xxx:
xxx: Match all icmp packets to 192.168.122.237/24, then
xxx: tag the packet with skb mark of decimal 17, then
xxx: Encode it with:
xxx:	ethertype 0xdead
xxx:	add skb->mark to whitelist of metadatum to send
xxx:	rewrite target dst MAC address to 02:15:15:15:15:15
xxx:
sudo $TC filter add dev $ETH parent 1: protocol ip prio 10  u32 \
match ip dst 192.168.122.237/24 \
match ip protocol 1 0xff \
flowid 1:2 \
action skbedit mark 17 \
action ife encode \
type 0xDEAD \
allow mark \
dst 02:15:15:15:15:15

xxx: Lets show the encoding policy
sudo tc -s filter ls dev $ETH parent 1: protocol ip
xxx:
filter pref 10 u32
filter pref 10 u32 fh 800: ht divisor 1
filter pref 10 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:2  (rule hit 0 success 0)
  match c0a87aed/ffffffff at 16 (success 0 )
  match 00010000/00ff0000 at 8 (success 0 )

	action order 1:  skbedit mark 17
	 index 6 ref 1 bind 1
 	Action statistics:
	Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
	backlog 0b 0p requeues 0

	action order 2: ife encode action pipe
	 index 3 ref 1 bind 1
	 dst MAC: 02:15:15:15:15:15 type: 0xDEAD
 	 Metadata: allow mark
 	Action statistics:
	Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
	backlog 0b 0p requeues 0
xxx:

test by sending ping from sender to destination

Signed-off-by: Jamal Hadi Salim 
Acked-by: Cong Wang 
Signed-off-by: David S. Miller

tc: introduce Flower classifier

2015-05-13T19:19:48+00:00

This patch introduces a flow-based filter. So far, the very essential
packet fields are supported.

This patch is only the first step. There is a lot of potential performance
improvements possible to implement. Also a lot of features are missing
now. They will be addressed in follow-up patches.

Signed-off-by: Jiri Pirko 
Acked-by: Jamal Hadi Salim 
Signed-off-by: David S. Miller

net: sched: Introduce connmark action

2015-01-19T21:02:06+00:00

This tc action allows you to retrieve the connection tracking mark
This action has been used heavily by openwrt for a few years now.

There are known limitations currently:

doesn't work for initial packets, since we only query the ct table.
  Fine given use case is for returning packets

no implicit defrag.
  frags should be rare so fix later..

won't work for more complex tasks, e.g. lookup of other extensions
  since we have no means to store results

we still have a 2nd lookup later on via normal conntrack path.
This shouldn't break anything though since skb->nfct isn't altered.

V2:
remove unnecessary braces (Jiri)
change the action identifier to 14 (Jiri)
Fix some stylistic issues caught by checkpatch
V3:
Move module params to bottom (Cong)
Get rid of tcf_hashinfo_init and friends and conform to newer API (Cong)

Acked-by: Jiri Pirko 
Signed-off-by: Felix Fietkau 
Signed-off-by: Jamal Hadi Salim 
Signed-off-by: David S. Miller

tc: add BPF based action

2015-01-18T04:51:10+00:00

This action provides a possibility to exec custom BPF code.

Signed-off-by: Jiri Pirko 
Signed-off-by: David S. Miller