Pull networking fixes from David Miller:

 1) Disable RISCV BPF JIT builds when !MMU, from Björn Töpel.

 2) nf_tables leaves dangling pointer after free, fix from Eric Dumazet.

 3) Out of boundary write in __xsk_rcv_memcpy(), fix from Li RongQing.

 4) Adjust icmp6 message source address selection when routes have a
    preferred source address set, from Tim Stallard.

 5) Be sure to validate HSR protocol version when creating new links,
    from Taehee Yoo.

 6) CAP_NET_ADMIN should be sufficient to manage l2tp tunnels even in
    non-initial namespaces, from Michael Weiß.

 7) Missing release firmware call in mlx5, from Eran Ben Elisha.

 8) Fix variable type in macsec_changelink(), caught by KASAN. Fix from
    Taehee Yoo.

 9) Fix pause frame negotiation in marvell phy driver, from Clemens
    Gruber.

10) Record RX queue early enough in tun packet paths such that XDP
    programs will see the correct RX queue index, from Gilberto Bertin.

11) Fix double unlock in mptcp, from Florian Westphal.

12) Fix offset overflow in ARM bpf JIT, from Luke Nelson.

13) marvell10g needs to soft reset PHY when coming out of low power
    mode, from Russell King.

14) Fix MTU setting regression in stmmac for some chip types, from
    Florian Fainelli.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (101 commits)
  amd-xgbe: Use __napi_schedule() in BH context
  mISDN: make dmril and dmrim static
  net: stmmac: dwmac-sunxi: Provide TX and RX fifo sizes
  net: dsa: mt7530: fix tagged frames pass-through in VLAN-unaware mode
  tipc: fix incorrect increasing of link window
  Documentation: Fix tcp_challenge_ack_limit default value
  net: tulip: make early_486_chipsets static
  dt-bindings: net: ethernet-phy: add desciption for ethernet-phy-id1234.d400
  ipv6: remove redundant assignment to variable err
  net/rds: Use ERR_PTR for rds_message_alloc_sgs()
  net: mscc: ocelot: fix untagged packet drops when enslaving to vlan aware bridge
  selftests/bpf: Check for correct program attach/detach in xdp_attach test
  libbpf: Fix type of old_fd in bpf_xdp_set_link_opts
  libbpf: Always specify expected_attach_type on program load if supported
  xsk: Add missing check on user supplied headroom size
  mac80211: fix channel switch trigger from unknown mesh peer
  mac80211: fix race in ieee80211_register_hw()
  net: marvell10g: soft-reset the PHY when coming out of low power
  net: marvell10g: report firmware version
  net/cxgb4: Check the return from t4_query_params properly
  ...

In commit 16ad3f4022bb ("tipc: introduce variable window congestion
control"), we allow link window to change with the congestion avoidance
algorithm. However, there is a bug that during the slow-start if packet
retransmission occurs, the link will enter the fast-recovery phase, set
its window to the 'ssthresh' which is never less than 300, so the link
window suddenly increases to that limit instead of decreasing.

Consequently, two issues have been observed:

- For broadcast-link: it can leave a gap between the link queues that a
new packet will be inserted and sent before the previous ones, i.e. not
in-order.

- For unicast: the algorithm does not work as expected, the link window
jumps to the slow-start threshold whereas packet retransmission occurs.

This commit fixes the issues by avoiding such the link window increase,
but still decreasing if the 'ssthresh' is lowered.

Fixes: 16ad3f4022bb ("tipc: introduce variable window congestion control")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

The variable err is being initialized with a value that is never read
and it is being updated later with a new value.  The initialization is
redundant and can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Returning the error code via a 'int *ret' when the function returns a
pointer is very un-kernely and causes gcc 10's static analysis to choke:

net/rds/message.c: In function ‘rds_message_map_pages’:
net/rds/message.c:358:10: warning: ‘ret’ may be used uninitialized in this function [-Wmaybe-uninitialized]
  358 |   return ERR_PTR(ret);

Use a typical ERR_PTR return instead.

Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf 2020-04-15

The following pull-request contains BPF updates for your *net* tree.

We've added 10 non-merge commits during the last 3 day(s) which contain
a total of 11 files changed, 238 insertions(+), 95 deletions(-).

The main changes are:

1) Fix offset overflow for BPF_MEM BPF_DW insn mapping on arm32 JIT,
   from Luke Nelson and Xi Wang.

2) Prevent mprotect() to make frozen & mmap()'ed BPF map writeable
   again, from Andrii Nakryiko and Jann Horn.

3) Fix type of old_fd in bpf_xdp_set_link_opts to int in libbpf and add
   selftests, from Toke Høiland-Jørgensen.

4) Fix AF_XDP to check that headroom cannot be larger than the available
   space in the chunk, from Magnus Karlsson.

5) Fix reset of XDP prog when expected_fd is set, from David Ahern.

6) Fix a segfault in bpftool's struct_ops command when BTF is not
   available, from Daniel T. Lee.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Johannes Berg says:

====================
A couple of fixes:
 * FTM responder policy netlink validation fix
   (but the only user validates again later)
 * kernel-doc fixes
 * a fix for a race in mac80211 radio registration vs. userspace
 * a mesh channel switch fix
 * a fix for a syzbot reported kasprintf() issue
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Add a check that the headroom cannot be larger than the available
space in the chunk. In the current code, a malicious user can set the
headroom to a value larger than the chunk size minus the fixed XDP
headroom. That way packets with a length larger than the supported
size in the umem could get accepted and result in an out-of-bounds
write.

Fixes: c0c77d8fb787 ("xsk: add user memory registration support sockopt")
Reported-by: Bui Quang Minh <minhquangbui99@gmail.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=207225
Link: https://lore.kernel.org/bpf/1586849715-23490-1-git-send-email-magnus.karlsson@intel.com

Previously mesh channel switch happens if beacon contains
CSA IE without checking the mesh peer info. Due to that
channel switch happens even if the beacon is not from
its own mesh peer. Fixing that by checking if the CSA
originated from the same mesh network before proceeding
for channel switch.

Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Link: https://lore.kernel.org/r/1585403604-29274-1-git-send-email-tamizhr@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

A race condition leading to a kernel crash is observed during invocation
of ieee80211_register_hw() on a dragonboard410c device having wcn36xx
driver built as a loadable module along with a wifi manager in user-space
waiting for a wifi device (wlanX) to be active.

Sequence diagram for a particular kernel crash scenario:

    user-space  ieee80211_register_hw()  ieee80211_tasklet_handler()
    ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
       |                    |                 |
       |<---phy0----wiphy_register()          |
       |-----iwd if_add---->|                 |
       |                    |<---IRQ----(RX packet)
       |              Kernel crash            |
       |              due to unallocated      |
       |              workqueue.              |
       |                    |                 |
       |       alloc_ordered_workqueue()      |
       |                    |                 |
       |              Misc wiphy init.        |
       |                    |                 |
       |            ieee80211_if_add()        |
       |                    |                 |

As evident from above sequence diagram, this race condition isn't specific
to a particular wifi driver but rather the initialization sequence in
ieee80211_register_hw() needs to be fixed. So re-order the initialization
sequence and the updated sequence diagram would look like:

    user-space  ieee80211_register_hw()  ieee80211_tasklet_handler()
    ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
       |                    |                 |
       |       alloc_ordered_workqueue()      |
       |                    |                 |
       |              Misc wiphy init.        |
       |                    |                 |
       |<---phy0----wiphy_register()          |
       |-----iwd if_add---->|                 |
       |                    |<---IRQ----(RX packet)
       |                    |                 |
       |            ieee80211_if_add()        |
       |                    |                 |

Cc: stable@vger.kernel.org
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/1586254255-28713-1-git-send-email-sumit.garg@linaro.org
[Johannes: fix rtnl imbalances]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

DSA and CPU ports can be configured in two ways. By default, the
driver should configure such ports to there maximum bandwidth. For
most use cases, this is sufficient. When this default is insufficient,
a phylink instance can be bound to such ports, and phylink will
configure the port, e.g. based on fixed-link properties. phylink
assumes the port is initially down. Given that the driver should have
already configured it to its maximum speed, ask the driver to down
the port before instantiating the phylink instance.

Fixes: 30c4a5b0aad8 ("net: mv88e6xxx: use resolved link config in mac_link_up()")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>