The do_send_email() will call die before restoring stty if sendmail
setting is not correct or sendmail is not installed. It is safer to
restore it in the beginning of dodie().

Link: https://lkml.kernel.org/r/167420617635.2988775.13045295332829029437.stgit@devnote3

Cc: John 'Warthog9' Hawley <warthog9@kernel.org>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

There is a disconnect between the run_command function and the
wait_for_input. The wait_for_input has a default timeout of 2 minutes. But
if that happens, the run_command loop will exit out to the waitpid() of
the executing command. This fails in that it no longer monitors the
command, and also, the ssh to the test box can hang when its finished, as
it's waiting for the pipe it's writing to to flush, but the loop that
reads that pipe has already exited, leaving the command stuck, and the
test hangs.

Instead, make the default "wait_for_input" of the run_command infinite,
and allow the user to override it if they want with a default timeout
option "RUN_TIMEOUT".

But this fixes the hang that happens when the pipe is full and the ssh
session never exits.

Cc: stable@vger.kernel.org
Fixes: 6e98d1b4415fe ("ktest: Add timeout to ssh command")
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

When monitoring the console output, the stdout is being redirected to do
so. If Ctrl^C is hit during this mode, the stdout is not back to the
console, the user does not see anything they type (no echo).

Add "end_monitor" to the SIGINT interrupt handler to give back the console
on Ctrl^C.

Cc: stable@vger.kernel.org
Fixes: 9f2cdcbbb90e7 ("ktest: Give console process a dedicated tty")
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

In the "reboot" command, it does a check of the machine to see if it is
still alive with a simple "ssh echo" command. If it fails, it will assume
that a normal "ssh reboot" is not possible and force a power cycle.

In this case, the "start_monitor" is executed, but the "end_monitor" is
not, and this causes the screen will not be given back to the console. That
is, after the test, a "reset" command needs to be performed, as "echo" is
turned off.

Cc: stable@vger.kernel.org
Fixes: 6474ace999edd ("ktest.pl: Powercycle the box on reboot if no connection can be made")
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

Allow variables to execute shell commands. Note, these are processed when
they are first seen while parsing the config file. This is useful if you
have the same config file used for multiple hosts (as they may be in a git
repository).

 HOSTNAME := ${shell hostname}
 DEFAULTS IF "${HOSTNAME}" == "frodo"

Link: https://lkml.kernel.org/r/20221207212944.277ee850@gandalf.local.home

Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>

grub2 has submenus where to use grub-reboot, it requires:

  grub-reboot X>Y

where X is the main index and Y is the submenu. Thus if you have:

menuentry 'Debian GNU/Linux' --class debian --class gnu-linux ...
	[...]
}
submenu 'Advanced options for Debian GNU/Linux' $menuentry_id_option ...
        menuentry 'Debian GNU/Linux, with Linux 6.0.0-4-amd64' --class debian --class gnu-linux ...
                [...]
        }
        menuentry 'Debian GNU/Linux, with Linux 6.0.0-4-amd64 (recovery mode)' --class debian --class gnu-linux ...
		[...]
        }
        menuentry 'Debian GNU/Linux, with Linux test' --class debian --class gnu-linux ...
                [...]
        }

And wanted to boot to the "Linux test" kernel, you need to run:

 # grub-reboot 1>2

As 1 is the second top menu (the submenu) and 2 is the third of the sub
menu entries.

Have the grub.cfg parsing for grub2 handle such cases.

Cc: stable@vger.kernel.org
Fixes: a15ba91361d46 ("ktest: Add support for grub2")
Reviewed-by: John 'Warthog9' Hawley (VMware) <warthog9@eaglescrag.net>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

After a full run of a make_min_config test, I noticed there were a lot of
CONFIGs still enabled that really should not be. Looking at them, I
noticed they were all defined as "default y". The issue is that the test
simple removes the config and re-runs make oldconfig, which enables it
again because it is set to default 'y'. Instead, explicitly disable the
config with writing "# CONFIG_FOO is not set" to the file to keep it from
being set again.

With this change, one of my box's minconfigs went from 768 configs set,
down to 521 configs set.

Link: https://lkml.kernel.org/r/20221202115936.016fce23@gandalf.local.home

Cc: stable@vger.kernel.org
Fixes: 0a05c769a9de5 ("ktest: Added config_bisect test type")
Reviewed-by: John 'Warthog9' Hawley (VMware) <warthog9@eaglescrag.net>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>

Update ktest example for the boot-time tracing with histogram
options. Note that since the histogram option uses "trace()" action
instead of "EVENT()", this updates the matching pattern too.

Link: https://lkml.kernel.org/r/162856130208.203126.4458319094852152589.stgit@devnote2

Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

bootconfig is a new feature that appends scripts onto the initrd, and the
kernel executes the scripts as an extended kernel command line.

Need to add tests to test that the happened. To test the bootconfig
properly, the initrd needs to be updated and the kernel rebooted. ktest is
the perfect solution to perform these tests.

Add a example bootconfig.conf in the tools/testing/ktest/examples/include
and example bootconfig scripts in tools/testing/ktest/examples/bootconfig
and also include verifier scripts that ktest will install on the target
and run to make sure that the bootconfig options in the scripts took place
after the target rebooted with the new initrd update.

Link: https://lkml.kernel.org/r/20210618112647.6a81dec5@oasis.local.home

Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

Perl, as with most scripting languages, is fairly flexible in how /
where you can define things, and it will (for the most part) do what you
would expect it to do.  This however can lead to situations, like with
ktest, where things get muddled over time.

This pushes the variable definitions back up to the top, followed by
functions, with the main script executables down at the bottom, INSTEAD
of being somewhat mish-mashed together in certain places.  This mostly
has the advantage of making it more obvious where things are initially
defined, what functions are there, and ACTUALLY where the main script
starts executing, and should make this a little more approachable.

Signed-off-by: John 'Warthog9' Hawley (VMware) <warthog9@eaglescrag.net>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>