USB: Dealias -110 code (more complete)

The purpose of this patch is to split off the case when a device does
not reply on the lower level (which is reported by HC hardware), and
a case when the device accepted the request, but does not reply at
upper level. This redefinition allows to diagnose issues easier,
without asking the user if the -110 happened "immediately".

The usbmon splits such cases already thanks to its timestamp, but
it's not always available.

I adjusted all drivers which I found affected (by searching for "urb").
Out of tree drivers may suffer a little bit, but I do not expect much
breakage. At worst they may print a few messages.

Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

24 files changed, 48 insertions, 60 deletions

diff --git a/Documentation/usb/error-codes.txt b/Documentation/usb/error-codes.txt
index 867f4c38f356..39c68f8c4e6c 100644
--- a/Documentation/usb/error-codes.txt
+++ b/Documentation/usb/error-codes.txt
@@ -98,13 +98,13 @@ one or more packets could finish before an error stops further endpoint I/O.
 			error, a failure to respond (often caused by
 			device disconnect), or some other fault.
 
--ETIMEDOUT (**)		No response packet received within the prescribed
+-ETIME (**)		No response packet received within the prescribed
 			bus turn-around time.  This error may instead be
 			reported as -EPROTO or -EILSEQ.
 
-			Note that the synchronous USB message functions
-			also use this code to indicate timeout expired
-			before the transfer completed.
+-ETIMEDOUT		Synchronous USB message functions use this code
+			to indicate timeout expired before the transfer
+			completed, and no other error was reported by HC.
 
 -EPIPE (**)		Endpoint stalled.  For non-control endpoints,
 			reset this status with usb_clear_halt().
@@ -163,6 +163,3 @@ usb_get_*/usb_set_*():
 usb_control_msg():
 usb_bulk_msg():
 -ETIMEDOUT		Timeout expired before the transfer completed.
-			In the future this code may change to -ETIME,
-			whose definition is a closer match to this sort
-			of error.
diff --git a/drivers/isdn/gigaset/bas-gigaset.c b/drivers/isdn/gigaset/bas-gigaset.c
index 3845defd4901..5cfbe6a38010 100644
--- a/drivers/isdn/gigaset/bas-gigaset.c
+++ b/drivers/isdn/gigaset/bas-gigaset.c
@@ -192,7 +192,7 @@ static char *get_usb_statmsg(int status)
 		return "bit stuffing error, timeout, or unknown USB error";
 	case -EILSEQ:
 		return "CRC mismatch, timeout, or unknown USB error";
-	case -ETIMEDOUT:
+	case -ETIME:
 		return "timed out";
 	case -EPIPE:
 		return "endpoint stalled";
diff --git a/drivers/isdn/hisax/hfc_usb.h b/drivers/isdn/hisax/hfc_usb.h
index ec52c1a7c22a..6349367ed480 100644
--- a/drivers/isdn/hisax/hfc_usb.h
+++ b/drivers/isdn/hisax/hfc_usb.h
@@ -137,11 +137,11 @@ static struct hfcusb_symbolic_list urb_errlist[] = {
 	{-ENXIO, "URB already queued"},
 	{-EFBIG, "Too much ISO frames requested"},
 	{-ENOSR, "Buffer error (overrun)"},
-	{-EPIPE, "Specified endpoint is stalled (device not responding)"},
+	{-EPIPE, "Specified endpoint is stalled"},
 	{-EOVERFLOW, "Babble (bad cable?)"},
 	{-EPROTO, "Bit-stuff error (bad cable?)"},
-	{-EILSEQ, "CRC/Timeout"},
-	{-ETIMEDOUT, "NAK (device does not respond)"},
+	{-EILSEQ, "CRC or missing token"},
+	{-ETIME, "Device did not respond"},
 	{-ESHUTDOWN, "Device unplugged"},
 	{-1, NULL}
 };
diff --git a/drivers/media/dvb/dvb-usb/dvb-usb-urb.c b/drivers/media/dvb/dvb-usb/dvb-usb-urb.c
index 9002f35aa952..88b283731bb8 100644
--- a/drivers/media/dvb/dvb-usb/dvb-usb-urb.c
+++ b/drivers/media/dvb/dvb-usb/dvb-usb-urb.c
@@ -80,7 +80,6 @@ static void dvb_usb_urb_complete(struct urb *urb, struct pt_regs *ptregs)
 
 	switch (urb->status) {
 		case 0:         /* success */
-		case -ETIMEDOUT:    /* NAK */
 			break;
 		case -ECONNRESET:   /* kill */
 		case -ENOENT:
diff --git a/drivers/media/dvb/ttusb-dec/ttusb_dec.c b/drivers/media/dvb/ttusb-dec/ttusb_dec.c
index 6c1cb770bcf5..c9d663549dff 100644
--- a/drivers/media/dvb/ttusb-dec/ttusb_dec.c
+++ b/drivers/media/dvb/ttusb-dec/ttusb_dec.c
@@ -215,7 +215,7 @@ static void ttusb_dec_handle_irq( struct urb *urb, struct pt_regs *regs)
 		case -ECONNRESET:
 		case -ENOENT:
 		case -ESHUTDOWN:
-		case -ETIMEDOUT:
+		case -ETIME:
 			/* this urb is dead, cleanup */
 			dprintk("%s:urb shutting down with status: %d\n",
 					__FUNCTION__, urb->status);
diff --git a/drivers/media/video/ov511.c b/drivers/media/video/ov511.c
index 1b07a61c2ebb..5d8cd283fcd8 100644
--- a/drivers/media/video/ov511.c
+++ b/drivers/media/video/ov511.c
@@ -301,10 +301,11 @@ static struct symbolic_list senlist[] = {
 static struct symbolic_list urb_errlist[] = {
 	{ -ENOSR,	"Buffer error (overrun)" },
 	{ -EPIPE,	"Stalled (device not responding)" },
-	{ -EOVERFLOW,	"Babble (bad cable?)" },
+	{ -EOVERFLOW,	"Babble (device sends too much data)" },
 	{ -EPROTO,	"Bit-stuff error (bad cable?)" },
-	{ -EILSEQ,	"CRC/Timeout" },
-	{ -ETIMEDOUT,	"NAK (device does not respond)" },
+	{ -EILSEQ,	"CRC/Timeout (bad cable?)" },
+	{ -ETIME,	"Device does not respond to token" },
+	{ -ETIMEDOUT,	"Device does not respond to command" },
 	{ -1, NULL }
 };
 
diff --git a/drivers/media/video/pwc/pwc-if.c b/drivers/media/video/pwc/pwc-if.c
index d4703944df9c..53c4b5790d5c 100644
--- a/drivers/media/video/pwc/pwc-if.c
+++ b/drivers/media/video/pwc/pwc-if.c
@@ -711,7 +711,7 @@ static void pwc_isoc_handler(struct urb *urb, struct pt_regs *regs)
 			case -EOVERFLOW:	errmsg = "Babble (bad cable?)"; break;
 			case -EPROTO:		errmsg = "Bit-stuff error (bad cable?)"; break;
 			case -EILSEQ:		errmsg = "CRC/Timeout (could be anything)"; break;
-			case -ETIMEDOUT:	errmsg = "NAK (device does not respond)"; break;
+			case -ETIME:		errmsg = "Device does not respond"; break;
 		}
 		PWC_DEBUG_FLOW("pwc_isoc_handler() called with status %d [%s].\n", urb->status, errmsg);
 		/* Give up after a number of contiguous errors on the USB bus.
diff --git a/drivers/media/video/w9968cf.c b/drivers/media/video/w9968cf.c
index 20f211b55ad4..2912326a5aef 100644
--- a/drivers/media/video/w9968cf.c
+++ b/drivers/media/video/w9968cf.c
@@ -586,15 +586,14 @@ static struct w9968cf_symbolic_list urb_errlist[] = {
 	{ -EFBIG,     "Too much ISO frames requested" },
 	{ -ENOSR,     "Buffer error (overrun)" },
 	{ -EPIPE,     "Specified endpoint is stalled (device not responding)"},
-	{ -EOVERFLOW, "Babble (bad cable?)" },
+	{ -EOVERFLOW, "Babble (too much data)" },
 	{ -EPROTO,    "Bit-stuff error (bad cable?)" },
 	{ -EILSEQ,    "CRC/Timeout" },
-	{ -ETIMEDOUT, "NAK (device does not respond)" },
+	{ -ETIME,     "Device does not respond to token" },
+	{ -ETIMEDOUT, "Device does not respond to command" },
 	{ -1, NULL }
 };
 
-
-
 /****************************************************************************
  * Memory management functions                                              *
  ****************************************************************************/
diff --git a/drivers/net/irda/irda-usb.c b/drivers/net/irda/irda-usb.c
index 2a0d538b387f..383cef1f5999 100644
--- a/drivers/net/irda/irda-usb.c
+++ b/drivers/net/irda/irda-usb.c
@@ -671,10 +671,8 @@ static void irda_usb_net_timeout(struct net_device *netdev)
 			 * Jean II */
 			done = 1;
 			break;
-		case -ECONNABORTED:		/* -103 */
-		case -ECONNRESET:		/* -104 */
-		case -ETIMEDOUT:		/* -110 */
-		case -ENOENT:			/* -2 (urb unlinked by us)  */
+		case -ECONNRESET:
+		case -ENOENT:			/* urb unlinked by us */
 		default:			/* ??? - Play safe */
 			urb->status = 0;
 			netif_wake_queue(self->netdev);
@@ -712,10 +710,8 @@ static void irda_usb_net_timeout(struct net_device *netdev)
 			 * Jean II */
 			done = 1;
 			break;
-		case -ECONNABORTED:		/* -103 */
-		case -ECONNRESET:		/* -104 */
-		case -ETIMEDOUT:		/* -110 */
-		case -ENOENT:			/* -2 (urb unlinked by us)  */
+		case -ECONNRESET:
+		case -ENOENT:			/* urb unlinked by us */
 		default:			/* ??? - Play safe */
 			if(skb != NULL) {
 				dev_kfree_skb_any(skb);
@@ -845,14 +841,14 @@ static void irda_usb_receive(struct urb *urb, struct pt_regs *regs)
 			self->stats.rx_crc_errors++;	
 			/* Also precursor to a hot-unplug on UHCI. */
 			/* Fallthrough... */
-		case -ECONNRESET:		/* -104 */
+		case -ECONNRESET:
 			/* Random error, if I remember correctly */
 			/* uhci_cleanup_unlink() is going to kill the Rx
 			 * URB just after we return. No problem, at this
 			 * point the URB will be idle ;-) - Jean II */
-		case -ESHUTDOWN:		/* -108 */
+		case -ESHUTDOWN:
 			/* That's usually a hot-unplug. Submit will fail... */
-		case -ETIMEDOUT:		/* -110 */
+		case -ETIME:
 			/* Usually precursor to a hot-unplug on OHCI. */
 		default:
 			self->stats.rx_errors++;
diff --git a/drivers/net/wireless/zd1201.c b/drivers/net/wireless/zd1201.c
index c52e9bcf8d02..f50ec10675d1 100644
--- a/drivers/net/wireless/zd1201.c
+++ b/drivers/net/wireless/zd1201.c
@@ -119,7 +119,7 @@ static void zd1201_usbfree(struct urb *urb, struct pt_regs *regs)
 	switch(urb->status) {
 		case -EILSEQ:
 		case -ENODEV:
-		case -ETIMEDOUT:
+		case -ETIME:
 		case -ENOENT:
 		case -EPIPE:
 		case -EOVERFLOW:
@@ -201,7 +201,7 @@ static void zd1201_usbrx(struct urb *urb, struct pt_regs *regs)
 	switch(urb->status) {
 		case -EILSEQ:
 		case -ENODEV:
-		case -ETIMEDOUT:
+		case -ETIME:
 		case -ENOENT:
 		case -EPIPE:
 		case -EOVERFLOW:
diff --git a/drivers/usb/host/isp116x.h b/drivers/usb/host/isp116x.h
index a1b7c3813d3a..b91e2edd9c5c 100644
--- a/drivers/usb/host/isp116x.h
+++ b/drivers/usb/host/isp116x.h
@@ -233,7 +233,7 @@ static const int cc_to_error[16] = {
 	/* Bit Stuff  */ -EPROTO,
 	/* Data Togg  */ -EILSEQ,
 	/* Stall      */ -EPIPE,
-	/* DevNotResp */ -ETIMEDOUT,
+	/* DevNotResp */ -ETIME,
 	/* PIDCheck   */ -EPROTO,
 	/* UnExpPID   */ -EPROTO,
 	/* DataOver   */ -EOVERFLOW,
diff --git a/drivers/usb/host/ohci.h b/drivers/usb/host/ohci.h
index 650d1bf21c1d..93fdc3c35341 100644
--- a/drivers/usb/host/ohci.h
+++ b/drivers/usb/host/ohci.h
@@ -159,7 +159,7 @@ static const int cc_to_error [16] = {
 	/* Bit Stuff  */               -EPROTO,
 	/* Data Togg  */               -EILSEQ,
 	/* Stall      */               -EPIPE,
-	/* DevNotResp */               -ETIMEDOUT,
+	/* DevNotResp */               -ETIME,
 	/* PIDCheck   */               -EPROTO,
 	/* UnExpPID   */               -EPROTO,
 	/* DataOver   */               -EOVERFLOW,
diff --git a/drivers/usb/host/sl811-hcd.c b/drivers/usb/host/sl811-hcd.c
index 8c17da37600b..3a586aab3939 100644
--- a/drivers/usb/host/sl811-hcd.c
+++ b/drivers/usb/host/sl811-hcd.c
@@ -597,7 +597,7 @@ done(struct sl811 *sl811, struct sl811h_ep *ep, u8 bank, struct pt_regs *regs)
 	/* error? retry, until "3 strikes" */
 	} else if (++ep->error_count >= 3) {
 		if (status & SL11H_STATMASK_TMOUT)
-			urbstat = -ETIMEDOUT;
+			urbstat = -ETIME;
 		else if (status & SL11H_STATMASK_OVF)
 			urbstat = -EOVERFLOW;
 		else
diff --git a/drivers/usb/input/hid-core.c b/drivers/usb/input/hid-core.c
index fc5b662ea177..2a3e9e9b4b3d 100644
--- a/drivers/usb/input/hid-core.c
+++ b/drivers/usb/input/hid-core.c
@@ -1023,7 +1023,8 @@ static void hid_irq_in(struct urb *urb, struct pt_regs *regs)
 			return;
 		case -EILSEQ:		/* protocol error or unplug */
 		case -EPROTO:		/* protocol error or unplug */
-		case -ETIMEDOUT:	/* NAK */
+		case -ETIME:		/* protocol error or unplug */
+		case -ETIMEDOUT:	/* Should never happen, but... */
 			clear_bit(HID_IN_RUNNING, &hid->iofl);
 			hid_io_error(hid);
 			return;
diff --git a/drivers/usb/input/itmtouch.c b/drivers/usb/input/itmtouch.c
index 86acb5f1907a..61966d719ca3 100644
--- a/drivers/usb/input/itmtouch.c
+++ b/drivers/usb/input/itmtouch.c
@@ -87,7 +87,7 @@ static void itmtouch_irq(struct urb *urb, struct pt_regs *regs)
 	case 0:
 		/* success */
 		break;
-	case -ETIMEDOUT:
+	case -ETIME:
 		/* this urb is timing out */
 		dbg("%s - urb timed out - was the device unplugged?",
 		    __FUNCTION__);
diff --git a/drivers/usb/input/mtouchusb.c b/drivers/usb/input/mtouchusb.c
index a9ccda8810e0..5dce951f2751 100644
--- a/drivers/usb/input/mtouchusb.c
+++ b/drivers/usb/input/mtouchusb.c
@@ -107,7 +107,7 @@ static void mtouchusb_irq(struct urb *urb, struct pt_regs *regs)
 	case 0:
 		/* success */
 		break;
-	case -ETIMEDOUT:
+	case -ETIME:
 		/* this urb is timing out */
 		dbg("%s - urb timed out - was the device unplugged?",
 		    __FUNCTION__);
diff --git a/drivers/usb/input/touchkitusb.c b/drivers/usb/input/touchkitusb.c
index 0149043ffb97..30b9f820e7a8 100644
--- a/drivers/usb/input/touchkitusb.c
+++ b/drivers/usb/input/touchkitusb.c
@@ -201,7 +201,7 @@ static void touchkit_irq(struct urb *urb, struct pt_regs *regs)
 	case 0:
 		/* success */
 		break;
-	case -ETIMEDOUT:
+	case -ETIME:
 		/* this urb is timing out */
 		dbg("%s - urb timed out - was the device unplugged?",
 		    __FUNCTION__);
diff --git a/drivers/usb/input/usbtouchscreen.c b/drivers/usb/input/usbtouchscreen.c
index a1be7840ea02..4640d1000d83 100644
--- a/drivers/usb/input/usbtouchscreen.c
+++ b/drivers/usb/input/usbtouchscreen.c
@@ -508,7 +508,7 @@ static void usbtouch_irq(struct urb *urb, struct pt_regs *regs)
 	case 0:
 		/* success */
 		break;
-	case -ETIMEDOUT:
+	case -ETIME:
 		/* this urb is timing out */
 		dbg("%s - urb timed out - was the device unplugged?",
 		    __FUNCTION__);
diff --git a/drivers/usb/misc/auerswald.c b/drivers/usb/misc/auerswald.c
index 4a329d8488b7..4fd2110b3411 100644
--- a/drivers/usb/misc/auerswald.c
+++ b/drivers/usb/misc/auerswald.c
@@ -806,7 +806,7 @@ static void auerbuf_releasebuf( pauerbuf_t bp)
 0		Initial, OK
 -EINPROGRESS	during submission until end
 -ENOENT		if urb is unlinked
--ETIMEDOUT	Transfer timed out, NAK
+-ETIME		Device did not respond
 -ENOMEM		Memory Overflow
 -ENODEV		Specified USB-device or bus doesn't exist
 -ENXIO		URB already queued
@@ -832,7 +832,7 @@ static int auerswald_status_retry (int status)
 {
 	switch (status) {
 	case 0:
-	case -ETIMEDOUT:
+	case -ETIME:
 	case -EOVERFLOW:
 	case -EAGAIN:
 	case -EPIPE:
diff --git a/drivers/usb/net/pegasus.c b/drivers/usb/net/pegasus.c
index ab21f960d255..b8e25af13f02 100644
--- a/drivers/usb/net/pegasus.c
+++ b/drivers/usb/net/pegasus.c
@@ -619,7 +619,7 @@ static void read_bulk_callback(struct urb *urb, struct pt_regs *regs)
 	switch (urb->status) {
 	case 0:
 		break;
-	case -ETIMEDOUT:
+	case -ETIME:
 		if (netif_msg_rx_err(pegasus))
 			pr_debug("%s: reset MAC\n", net->name);
 		pegasus->flags &= ~PEGASUS_RX_BUSY;
diff --git a/drivers/usb/net/rtl8150.c b/drivers/usb/net/rtl8150.c
index a72685b96061..2364c2099387 100644
--- a/drivers/usb/net/rtl8150.c
+++ b/drivers/usb/net/rtl8150.c
@@ -438,7 +438,7 @@ static void read_bulk_callback(struct urb *urb, struct pt_regs *regs)
 		break;
 	case -ENOENT:
 		return;	/* the urb is in unlink state */
-	case -ETIMEDOUT:
+	case -ETIME:
 		warn("may be reset is needed?..");
 		goto goon;
 	default:
diff --git a/drivers/usb/net/usbnet.c b/drivers/usb/net/usbnet.c
index 8e8e74d40530..98a522f1e264 100644
--- a/drivers/usb/net/usbnet.c
+++ b/drivers/usb/net/usbnet.c
@@ -425,9 +425,9 @@ static void rx_complete (struct urb *urb, struct pt_regs *regs)
 	    // we get controller i/o faults during khubd disconnect() delays.
 	    // throttle down resubmits, to avoid log floods; just temporarily,
 	    // so we still recover when the fault isn't a khubd delay.
-	    case -EPROTO:		// ehci
-	    case -ETIMEDOUT:		// ohci
-	    case -EILSEQ:		// uhci
+	    case -EPROTO:
+	    case -ETIME:
+	    case -EILSEQ:
 		dev->stats.rx_errors++;
 		if (!timer_pending (&dev->delay)) {
 			mod_timer (&dev->delay, jiffies + THROTTLE_JIFFIES);
@@ -821,9 +821,9 @@ static void tx_complete (struct urb *urb, struct pt_regs *regs)
 
 		// like rx, tx gets controller i/o faults during khubd delays
 		// and so it uses the same throttling mechanism.
-		case -EPROTO:		// ehci
-		case -ETIMEDOUT:	// ohci
-		case -EILSEQ:		// uhci
+		case -EPROTO:
+		case -ETIME:
+		case -EILSEQ:
 			if (!timer_pending (&dev->delay)) {
 				mod_timer (&dev->delay,
 					jiffies + THROTTLE_JIFFIES);
diff --git a/drivers/usb/storage/transport.c b/drivers/usb/storage/transport.c
index d6acc92a4ae3..f23514c4e649 100644
--- a/drivers/usb/storage/transport.c
+++ b/drivers/usb/storage/transport.c
@@ -294,11 +294,6 @@ static int interpret_urb_result(struct us_data *us, unsigned int pipe,
 			return USB_STOR_XFER_ERROR;
 		return USB_STOR_XFER_STALLED;
 
-	/* timeout or excessively long NAK */
-	case -ETIMEDOUT:
-		US_DEBUGP("-- timeout or NAK\n");
-		return USB_STOR_XFER_ERROR;
-
 	/* babble - the device tried to send more than we wanted to read */
 	case -EOVERFLOW:
 		US_DEBUGP("-- babble\n");
diff --git a/sound/usb/usbmidi.c b/sound/usb/usbmidi.c
index 5105b6b05748..abe29dadd979 100644
--- a/sound/usb/usbmidi.c
+++ b/sound/usb/usbmidi.c
@@ -181,9 +181,9 @@ static int snd_usbmidi_urb_error(int status)
 	case -ENODEV:
 		return -ENODEV;
 	/* errors that might occur during unplugging */
-	case -EPROTO:    /* EHCI */
-	case -ETIMEDOUT: /* OHCI */
-	case -EILSEQ:    /* UHCI */
+	case -EPROTO:
+	case -ETIME:
+	case -EILSEQ:
 		return -EIO;
 	default:
 		snd_printk(KERN_ERR "urb status %d\n", status);