summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
authorAntonino A. Daplas <adaplas@gmail.com>2005-09-12 09:18:12 +0800
committerLinus Torvalds <torvalds@g5.osdl.org>2005-09-11 20:43:48 -0700
commitc93a777103263c2a610a49771c6336f7a53d8ab7 (patch)
tree1152effff9831348dbf9ffb1766dd1208d6ea272
parent747a5054c0663a21c440524bdac1bca31be0d20e (diff)
[PATCH] i810fb: Update i810fb documentation
Update i810fb documentation to describe new features and configuration changes. Signed-off-by: Antonino Daplas <adaplas@pol.net> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-rw-r--r--Documentation/fb/intel810.txt56
1 files changed, 30 insertions, 26 deletions
diff --git a/Documentation/fb/intel810.txt b/Documentation/fb/intel810.txt
index fd68b162e4a1..4f0d6bc789ef 100644
--- a/Documentation/fb/intel810.txt
+++ b/Documentation/fb/intel810.txt
@@ -5,6 +5,7 @@ Intel 810/815 Framebuffer driver
March 17, 2002
First Released: July 2001
+ Last Update: September 12, 2005
================================================================
A. Introduction
@@ -44,6 +45,8 @@ B. Features
- Hardware Cursor Support
+ - Supports EDID probing either by DDC/I2C or through the BIOS
+
C. List of available options
a. "video=i810fb"
@@ -52,14 +55,17 @@ C. List of available options
Recommendation: required
b. "xres:<value>"
- select horizontal resolution in pixels
+ select horizontal resolution in pixels. (This parameter will be
+ ignored if 'mode_option' is specified. See 'o' below).
Recommendation: user preference
(default = 640)
c. "yres:<value>"
select vertical resolution in scanlines. If Discrete Video Timings
- is enabled, this will be ignored and computed as 3*xres/4.
+ is enabled, this will be ignored and computed as 3*xres/4. (This
+ parameter will be ignored if 'mode_option' is specified. See 'o'
+ below)
Recommendation: user preference
(default = 480)
@@ -86,7 +92,8 @@ C. List of available options
g. "hsync1/hsync2:<value>"
select the minimum and maximum Horizontal Sync Frequency of the
monitor in KHz. If a using a fixed frequency monitor, hsync1 must
- be equal to hsync2.
+ be equal to hsync2. If EDID probing is successful, these will be
+ ignored and values will be taken from the EDID block.
Recommendation: check monitor manual for correct values
default (29/30)
@@ -94,7 +101,8 @@ C. List of available options
h. "vsync1/vsync2:<value>"
select the minimum and maximum Vertical Sync Frequency of the monitor
in Hz. You can also use this option to lock your monitor's refresh
- rate.
+ rate. If EDID probing is successful, these will be ignored and values
+ will be taken from the EDID block.
Recommendation: check monitor manual for correct values
(default = 60/60)
@@ -154,7 +162,11 @@ C. List of available options
Recommendation: do not set
(default = not set)
-
+ o. <xres>x<yres>[-<bpp>][@<refresh>]
+ The driver will now accept specification of boot mode option. If this
+ is specified, the options 'xres' and 'yres' will be ignored. See
+ Documentation/fb/modedb.txt for usage.
+
D. Kernel booting
Separate each option/option-pair by commas (,) and the option from its value
@@ -176,7 +188,10 @@ will be computed based on the hsync1/hsync2 and vsync1/vsync2 values.
IMPORTANT:
You must include hsync1, hsync2, vsync1 and vsync2 to enable video modes
-better than 640x480 at 60Hz.
+better than 640x480 at 60Hz. HOWEVER, if your chipset/display combination
+supports I2C and has an EDID block, you can safely exclude hsync1, hsync2,
+vsync1 and vsync2 parameters. These parameters will be taken from the EDID
+block.
E. Module options
@@ -217,32 +232,21 @@ F. Setup
This is required. The option is under "Character Devices"
d. Under "Graphics Support", select "Intel 810/815" either statically
- or as a module. Choose "use VESA GTF for video timings" if you
- need to maximize the capability of your display. To be on the
+ or as a module. Choose "use VESA Generalized Timing Formula" if
+ you need to maximize the capability of your display. To be on the
safe side, you can leave this unselected.
- e. If you want a framebuffer console, enable it under "Console
+ e. If you want support for DDC/I2C probing (Plug and Play Displays),
+ set 'Enable DDC Support' to 'y'. To make this option appear, set
+ 'use VESA Generalized Timing Formula' to 'y'.
+
+ f. If you want a framebuffer console, enable it under "Console
Drivers"
- f. Compile your kernel.
+ g. Compile your kernel.
- g. Load the driver as described in section D and E.
+ h. Load the driver as described in section D and E.
- Optional:
- h. If you are going to run XFree86 with its native drivers, the
- standard XFree86 4.1.0 and 4.2.0 drivers should work as is.
- However, there's a bug in the XFree86 i810 drivers. It attempts
- to use XAA even when switched to the console. This will crash
- your server. I have a fix at this site:
-
- http://i810fb.sourceforge.net.
-
- You can either use the patch, or just replace
-
- /usr/X11R6/lib/modules/drivers/i810_drv.o
-
- with the one provided at the website.
-
i. Try the DirectFB (http://www.directfb.org) + the i810 gfxdriver
patch to see the chipset in action (or inaction :-).