Merge tag 'iio-for-3.20a_take2' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-testing

Jonathan writes:

First round of IIO new drivers, cleanups and functionality for the 3.20 cycle take 2

Updated pull request with Daniel's fix on top for the power management
Kconfig changes that had snuck in since last update of the IIO tree
worked it's way through from mainline.

Original pull message

New device support
* jsa1212 proxmity / ambient light sensor
* SM08500 supported added to the kxcjk-1013 accelerometer driver
* KMX61 Accelerometer/Magnetometer.  This took a somewhat rocky path
  being first merged, then reverted for a rewrite after a discussion of
  how to support additional functionality and finally being merged prior
  to some last reviews coming in, with resultant follow up patches.
* Freescale mma9551l driver (minor follow up warning supression patch).
* Semtech SX9500 proximity device driver.
* ak8975 gains support for ak09911 and ak09912 and drop the standalone driver
  for the ak09911.

New functionality
 * Dummy driver gains some virtual registers making it more flexible.
 * IIO_ACTIVITY channel types, with modifiers running, walking etc.  This is
   to support on chip motion clasifiers.  As such it is in the form of a
   confidence percentage.  The only devices so far only do binary decisions
   but this gives us room when other devices give more nuanced clasification.
 * IIO_EV_DIR_NONE type for events where there is no obvious direction.
   First case is step detection.
 * IIO_STEPS channel type for pedometers.
 * ENABLE mask element used to control turning on counting types such as
   the pedometer that need a 'start point'.
 * INSTANCE event type to support things that happen once.
 * info element for height calibration (used in various motion estimation
   algorithms). Note heigh tof use
 * dummy driver demonstration of the use of all the new bits above.
 * event monitor support for the new events.
 * inv_mpu6050 gains an i2c mux to allow bypassing the device to access
   additional devices connected on the other side of it.  Note that in
   Windows these are handled by firmware on the device and not exposed
   directly.
 * inv_mpu6050 gains ACPI enumeration.
 * inkern interface gains iio_write_channel_raw to allow in kernel users
   of DAC functionality via a simple wrapper.
 * Document input current readings in the ABI docs.
 * Add an error message when we get an out of range error in device tree
   processing for the in kernel interfaces.  Basically a device tree debugging
   aid.
 * Add a sanity check that a scan index for a channel is unique during
   registration.  There to help catch bugs as this should never happen
   in a bug free driver.

Cleanups and fixlets

 A rework of buffer registration from Lars - a precursor to some other
 upcoming new stuff (a few patches from others rolled in here as well).
 * Ensure all drivers register the same channels for the device and buffer.
 * Move buffer registration into the core rather than using the old
   two step approach.  Now we have simple ways of using a unified set channels
   for both without requiring channels be exposed by both interface, this
   removes a fair bit of boilerplate.
 * Stop sca3000 and ad5933 (both in staging) enabling buffer channels by
   default. It has long be convention in IIO to startup with no channels
   enabled and leave it up to userspace to say what goes in the buffer.
   Getting rid of these allows us to drop export of iio_scan_mask_set.
 * Drop get_bytes_per_datum from iio_buffer_access_funcs as not been used
   for a while.
 * Allocate standard buffer attributes in the core rather than in every
   driver with a buffer.
 * Make the length attribute read only when a driver is not able to set
   the length.
 * Drop the get_length callback for buffers as it is already available in
   struct iio_buffer.
 * Drop an unused arguement form iio_kfifo_allocate and add devm allocator
   for it.
 * some kconfig entries gain anotation with the resulting module name.
 * Fix a resulting compile issue in dummy driver due to a stub taking
   wrong parameters as a result of the above rework.
 * Fix an off by 2 error in copying the core assigned buffer attributes.

Other cleanups,
 * Trivial space before comma fixups.
 * ak8975 fixlets - none critical.  Rework to allow more device support.
 * Drop unnecessary sizeof(u8) calls.
 * bmp280 - refactor the compensation code to reduce copy operations and
   code length.  A second patch futher optimized this and performed some
   other minor cleanups.
 * kxcjk-1013 - various power control cleanups to avoid unnecessary enable
   / disable of device.  Make sure it is only controlled at all if CONFIG_PM
   is enabled.  Also som cleanups of error paths.
 * Small cleanups in adf4530 driver - pointless message and unnecessary braces.
 * Clarifiy the proximity ABI docs to make it clear it should get bigger
   as we move futher away.
 * Drop a misleading comment form industrialio-core.c
 * Trivial white space cleanups.
 * sca3000 looses an unused debug function.
 * Fix char unsigned ordering in ad8366
 * Increase the sleep time in ad9523 to make it predictable (value didn't
   really matter so make it more than 20 msecs)
 * mxs-lradc touchscreen property cleanups in device tree are fixed to ensure
   the meet all the 'interesting' documentation.
 * A couple of cleanups for the staging ad5933 driver to avoid unnecessary
   conversion to a processed temperature vlaue in kernel and remove
   platform data form the state structure as not needed after probe.
 * Fix a wrong scale factor in the docs.

Misc
 * Add IIO include files to the maintainers entry.

1 files changed, 94 insertions, 1 deletions

diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio
index 117521dbf2b3..831db8623e4b 100644
--- a/Documentation/ABI/testing/sysfs-bus-iio
+++ b/Documentation/ABI/testing/sysfs-bus-iio
@@ -92,6 +92,18 @@ Description:
 		is required is a consistent labeling.  Units after application
 		of scale and offset are millivolts.
 
+What:		/sys/bus/iio/devices/iio:deviceX/in_currentY_raw
+What:		/sys/bus/iio/devices/iio:deviceX/in_currentY_supply_raw
+KernelVersion:	3.17
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Raw (unscaled no bias removal etc.) current measurement from
+		channel Y. In special cases where the channel does not
+		correspond to externally available input one of the named
+		versions may be used. The number must always be specified and
+		unique to allow association with event codes. Units after
+		application of scale and offset are milliamps.
+
 What:		/sys/bus/iio/devices/iio:deviceX/in_capacitanceY_raw
 KernelVersion:	3.2
 Contact:	linux-iio@vger.kernel.org
@@ -234,6 +246,8 @@ What:		/sys/bus/iio/devices/iio:deviceX/in_accel_y_offset
 What:		/sys/bus/iio/devices/iio:deviceX/in_accel_z_offset
 What:		/sys/bus/iio/devices/iio:deviceX/in_voltageY_offset
 What:		/sys/bus/iio/devices/iio:deviceX/in_voltage_offset
+What:		/sys/bus/iio/devices/iio:deviceX/in_currentY_offset
+What:		/sys/bus/iio/devices/iio:deviceX/in_current_offset
 What:		/sys/bus/iio/devices/iio:deviceX/in_tempY_offset
 What:		/sys/bus/iio/devices/iio:deviceX/in_temp_offset
 What:		/sys/bus/iio/devices/iio:deviceX/in_pressureY_offset
@@ -262,6 +276,9 @@ What:		/sys/bus/iio/devices/iio:deviceX/in_voltage_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_voltage-voltage_scale
 What:		/sys/bus/iio/devices/iio:deviceX/out_voltageY_scale
 What:		/sys/bus/iio/devices/iio:deviceX/out_altvoltageY_scale
+What:		/sys/bus/iio/devices/iio:deviceX/in_currentY_scale
+What:		/sys/bus/iio/devices/iio:deviceX/in_currentY_supply_scale
+What:		/sys/bus/iio/devices/iio:deviceX/in_current_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_accel_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_accel_peak_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_anglvel_scale
@@ -323,6 +340,14 @@ Description:
 		production inaccuracies).  If shared across all channels,
 		<type>_calibscale is used.
 
+What:		/sys/bus/iio/devices/iio:deviceX/in_steps_calibheight
+KernelVersion:	3.19
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Height of the user (in centimeters) used by some pedometers
+		to compute the stride length, distance, speed and activity
+		type.
+
 What:		/sys/bus/iio/devices/iio:deviceX/in_accel_scale_available
 What:		/sys/.../iio:deviceX/in_voltageX_scale_available
 What:		/sys/.../iio:deviceX/in_voltage-voltage_scale_available
@@ -790,6 +815,40 @@ Description:
 		met before an event is generated. If direction is not
 		specified then this period applies to both directions.
 
+What:		/sys/.../events/in_activity_still_thresh_rising_en
+What:		/sys/.../events/in_activity_still_thresh_falling_en
+What:		/sys/.../events/in_activity_walking_thresh_rising_en
+What:		/sys/.../events/in_activity_walking_thresh_falling_en
+What:		/sys/.../events/in_activity_jogging_thresh_rising_en
+What:		/sys/.../events/in_activity_jogging_thresh_falling_en
+What:		/sys/.../events/in_activity_running_thresh_rising_en
+What:		/sys/.../events/in_activity_running_thresh_falling_en
+KernelVersion:	3.19
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Enables or disables activitity events. Depending on direction
+		an event is generated when sensor ENTERS or LEAVES a given state.
+
+What:		/sys/.../events/in_activity_still_thresh_rising_value
+What:		/sys/.../events/in_activity_still_thresh_falling_value
+What:		/sys/.../events/in_activity_walking_thresh_rising_value
+What:		/sys/.../events/in_activity_walking_thresh_falling_value
+What:		/sys/.../events/in_activity_jogging_thresh_rising_value
+What:		/sys/.../events/in_activity_jogging_thresh_falling_value
+What:		/sys/.../events/in_activity_running_thresh_rising_value
+What:		/sys/.../events/in_activity_running_thresh_falling_value
+KernelVersion:	3.19
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Confidence value (in units as percentage) to be used
+		for deciding when an event should be generated. E.g for
+		running: If the confidence value reported by the sensor
+		is greater than in_activity_running_thresh_rising_value
+		then the sensor ENTERS running state. Conversely, if the
+		confidence value reported by the sensor is lower than
+		in_activity_running_thresh_falling_value then the sensor
+		is LEAVING running state.
+
 What:		/sys/.../iio:deviceX/events/in_accel_mag_en
 What:		/sys/.../iio:deviceX/events/in_accel_mag_rising_en
 What:		/sys/.../iio:deviceX/events/in_accel_mag_falling_en
@@ -822,6 +881,13 @@ Description:
 		number or direction is not specified, applies to all channels of
 		this type.
 
+What:		/sys/.../events/in_steps_instance_en
+KernelVersion:	3.19
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Enables or disables step detection. Each time the user takes a step an
+		event of this type will be generated.
+
 What:		/sys/bus/iio/devices/iio:deviceX/trigger/current_trigger
 KernelVersion:	2.6.35
 Contact:	linux-iio@vger.kernel.org
@@ -956,6 +1022,16 @@ Description:
 		and the relevant _type attributes to establish the data storage
 		format.
 
+What:		/sys/.../iio:deviceX/in_activity_still_input
+What:		/sys/.../iio:deviceX/in_activity_walking_input
+What:		/sys/.../iio:deviceX/in_activity_jogging_input
+What:		/sys/.../iio:deviceX/in_activity_running_input
+KernelVersion:	3.19
+Contact:	linux-iio@vger.kernel.org
+Description:
+		This attribute is used to read the confidence for an activity
+		expressed in units as percentage.
+
 What:		/sys/.../iio:deviceX/in_anglvel_z_quadrature_correction_raw
 KernelVersion:	2.6.38
 Contact:	linux-iio@vger.kernel.org
@@ -992,7 +1068,9 @@ Description:
 		reflectivity of infrared or ultrasound emitted.
 		Often these sensors are unit less and as such conversion
 		to SI units is not possible.  Where it is, the units should
-		be meters.
+		be meters.  If such a conversion is not possible, the reported
+		values should behave in the same way as a distance, i.e. lower
+		values indicate something is closer to the sensor.
 
 What:		/sys/.../iio:deviceX/in_illuminanceY_input
 What:		/sys/.../iio:deviceX/in_illuminanceY_raw
@@ -1051,3 +1129,18 @@ Description:
 		after application of scale and offset. If no offset or scale is
 		present, output should be considered as processed with the
 		unit in milliamps.
+
+What:		/sys/.../iio:deviceX/in_steps_en
+KernelVersion:	3.19
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Activates the step counter. After activation, the number of steps
+		taken by the user will be counted in hardware and exported through
+		in_steps_input.
+
+What:		/sys/.../iio:deviceX/in_steps_input
+KernelVersion:	3.19
+Contact:	linux-iio@vger.kernel.org
+Description:
+		This attribute is used to read the number of steps taken by the user
+		since the last reboot while activated.