dt-bindings: consolidate display related bindings

This is a quite large renaming to consolidate display related bindings
into a single "display" directory from various scattered locations of
video, drm, gpu, fb, mipi, and panel. The prior location was somewhat
based on the Linux driver location, but bindings should be independent
of that.

Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>

10 files changed, 616 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/display/exynos/exynos-mic.txt b/Documentation/devicetree/bindings/display/exynos/exynos-mic.txt
new file mode 100644
index 000000000000..0fba2ee6440a
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/exynos/exynos-mic.txt
@@ -0,0 +1,51 @@
+Device-Tree bindings for Samsung Exynos SoC mobile image compressor (MIC)
+
+MIC (mobile image compressor) resides between decon and mipi dsi. Mipi dsi is
+not capable to transfer high resoltuion frame data as decon can send. MIC
+solves this problem by compressing the frame data by 1/2 before it is
+transferred through mipi dsi. The compressed frame data must be uncompressed in
+the panel PCB.
+
+Required properties:
+- compatible: value should be "samsung,exynos5433-mic".
+- reg: physical base address and length of the MIC registers set and system
+       register of mic.
+- clocks: must include clock specifiers corresponding to entries in the
+	  clock-names property.
+- clock-names: list of clock names sorted in the same order as the clocks
+	       property. Must contain "pclk_mic0", "sclk_rgb_vclk_to_mic0".
+- samsung,disp-syscon: the reference node for syscon for DISP block.
+- ports: contains a port which is connected to decon node and dsi node.
+	 address-cells and size-cells must 1 and 0, respectively.
+- port: contains an endpoint node which is connected to the endpoint in the
+	decon node or dsi node. The reg value must be 0 and 1 respectively.
+
+Example:
+SoC specific DT entry:
+mic: mic@13930000 {
+	compatible = "samsung,exynos5433-mic";
+	reg = <0x13930000 0x48>;
+	clocks = <&cmu_disp CLK_PCLK_MIC0>,
+	       <&cmu_disp CLK_SCLK_RGB_VCLK_TO_MIC0>;
+	clock-names = "pclk_mic0", "sclk_rgb_vclk_to_mic0";
+	samsung,disp-syscon = <&syscon_disp>;
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			mic_to_decon: endpoint {
+				remote-endpoint = <&decon_to_mic>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+			mic_to_dsi: endpoint {
+				remote-endpoint = <&dsi_to_mic>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt b/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt
new file mode 100644
index 000000000000..377afbf5122a
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt
@@ -0,0 +1,65 @@
+Device-Tree bindings for Samsung Exynos SoC display controller (DECON)
+
+DECON (Display and Enhancement Controller) is the Display Controller for the
+Exynos series of SoCs which transfers the image data from a video memory
+buffer to an external LCD interface.
+
+Required properties:
+- compatible: value should be "samsung,exynos5433-decon";
+- reg: physical base address and length of the DECON registers set.
+- interrupts: should contain a list of all DECON IP block interrupts in the
+	      order: VSYNC, LCD_SYSTEM. The interrupt specifier format
+	      depends on the interrupt controller used.
+- interrupt-names: should contain the interrupt names: "vsync", "lcd_sys"
+		   in the same order as they were listed in the interrupts
+		   property.
+- clocks: must include clock specifiers corresponding to entries in the
+	  clock-names property.
+- clock-names: list of clock names sorted in the same order as the clocks
+	       property. Must contain "aclk_decon", "aclk_smmu_decon0x",
+	       "aclk_xiu_decon0x", "pclk_smmu_decon0x", clk_decon_vclk",
+	       "sclk_decon_eclk"
+- ports: contains a port which is connected to mic node. address-cells and
+	 size-cells must 1 and 0, respectively.
+- port: contains an endpoint node which is connected to the endpoint in the mic
+	node. The reg value muset be 0.
+- i80-if-timings: specify whether the panel which is connected to decon uses
+		  i80 lcd interface or mipi video interface. This node contains
+		  no timing information as that of fimd does. Because there is
+		  no register in decon to specify i80 interface timing value,
+		  it is not needed, but make it remain to use same kind of node
+		  in fimd and exynos7 decon.
+
+Example:
+SoC specific DT entry:
+decon: decon@13800000 {
+	compatible = "samsung,exynos5433-decon";
+	reg = <0x13800000 0x2104>;
+	clocks = <&cmu_disp CLK_ACLK_DECON>, <&cmu_disp CLK_ACLK_SMMU_DECON0X>,
+		<&cmu_disp CLK_ACLK_XIU_DECON0X>,
+		<&cmu_disp CLK_PCLK_SMMU_DECON0X>,
+		<&cmu_disp CLK_SCLK_DECON_VCLK>,
+		<&cmu_disp CLK_SCLK_DECON_ECLK>;
+	clock-names = "aclk_decon", "aclk_smmu_decon0x", "aclk_xiu_decon0x",
+		"pclk_smmu_decon0x", "sclk_decon_vclk", "sclk_decon_eclk";
+	interrupt-names = "vsync", "lcd_sys";
+	interrupts = <0 202 0>, <0 203 0>;
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			decon_to_mic: endpoint {
+				remote-endpoint = <&mic_to_decon>;
+			};
+		};
+	};
+};
+
+Board specific DT entry:
+&decon {
+	i80-if-timings {
+	};
+};
diff --git a/Documentation/devicetree/bindings/display/exynos/exynos7-decon.txt b/Documentation/devicetree/bindings/display/exynos/exynos7-decon.txt
new file mode 100644
index 000000000000..3938caacf11c
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/exynos/exynos7-decon.txt
@@ -0,0 +1,68 @@
+Device-Tree bindings for Samsung Exynos7 SoC display controller (DECON)
+
+DECON (Display and Enhancement Controller) is the Display Controller for the
+Exynos7 series of SoCs which transfers the image data from a video memory
+buffer to an external LCD interface.
+
+Required properties:
+- compatible: value should be "samsung,exynos7-decon";
+
+- reg: physical base address and length of the DECON registers set.
+
+- interrupt-parent: should be the phandle of the decon controller's
+		parent interrupt controller.
+
+- interrupts: should contain a list of all DECON IP block interrupts in the
+		 order: FIFO Level, VSYNC, LCD_SYSTEM. The interrupt specifier
+		 format depends on the interrupt controller used.
+
+- interrupt-names: should contain the interrupt names: "fifo", "vsync",
+	"lcd_sys", in the same order as they were listed in the interrupts
+        property.
+
+- pinctrl-0: pin control group to be used for this controller.
+
+- pinctrl-names: must contain a "default" entry.
+
+- clocks: must include clock specifiers corresponding to entries in the
+         clock-names property.
+
+- clock-names: list of clock names sorted in the same order as the clocks
+               property. Must contain "pclk_decon0", "aclk_decon0",
+	       "decon0_eclk", "decon0_vclk".
+- i80-if-timings: timing configuration for lcd i80 interface support.
+
+Optional Properties:
+- samsung,power-domain: a phandle to DECON power domain node.
+- display-timings: timing settings for DECON, as described in document [1].
+		Can be used in case timings cannot be provided otherwise
+		or to override timings provided by the panel.
+
+[1]: Documentation/devicetree/bindings/display/display-timing.txt
+
+Example:
+
+SoC specific DT entry:
+
+	decon@13930000 {
+		compatible = "samsung,exynos7-decon";
+		interrupt-parent = <&combiner>;
+		reg = <0x13930000 0x1000>;
+		interrupt-names = "lcd_sys", "vsync", "fifo";
+		interrupts = <0 188 0>, <0 189 0>, <0 190 0>;
+		clocks = <&clock_disp PCLK_DECON_INT>,
+			 <&clock_disp ACLK_DECON_INT>,
+			 <&clock_disp SCLK_DECON_INT_ECLK>,
+			 <&clock_disp SCLK_DECON_INT_EXTCLKPLL>;
+		clock-names = "pclk_decon0", "aclk_decon0", "decon0_eclk",
+				"decon0_vclk";
+		status = "disabled";
+	};
+
+Board specific DT entry:
+
+	decon@13930000 {
+		pinctrl-0 = <&lcd_clk &pwm1_out>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
new file mode 100644
index 000000000000..64693f2ebc51
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
@@ -0,0 +1,120 @@
+The Exynos display port interface should be configured based on
+the type of panel connected to it.
+
+We use two nodes:
+	-dp-controller node
+	-dptx-phy node(defined inside dp-controller node)
+
+For the DP-PHY initialization, we use the dptx-phy node.
+Required properties for dptx-phy: deprecated, use phys and phy-names
+	-reg: deprecated
+		Base address of DP PHY register.
+	-samsung,enable-mask: deprecated
+		The bit-mask used to enable/disable DP PHY.
+
+For the Panel initialization, we read data from dp-controller node.
+Required properties for dp-controller:
+	-compatible:
+		should be "samsung,exynos5-dp".
+	-reg:
+		physical base address of the controller and length
+		of memory mapped region.
+	-interrupts:
+		interrupt combiner values.
+	-clocks:
+		from common clock binding: handle to dp clock.
+	-clock-names:
+		from common clock binding: Shall be "dp".
+	-interrupt-parent:
+		phandle to Interrupt combiner node.
+	-phys:
+		from general PHY binding: the phandle for the PHY device.
+	-phy-names:
+		from general PHY binding: Should be "dp".
+	-samsung,color-space:
+		input video data format.
+			COLOR_RGB = 0, COLOR_YCBCR422 = 1, COLOR_YCBCR444 = 2
+	-samsung,dynamic-range:
+		dynamic range for input video data.
+			VESA = 0, CEA = 1
+	-samsung,ycbcr-coeff:
+		YCbCr co-efficients for input video.
+			COLOR_YCBCR601 = 0, COLOR_YCBCR709 = 1
+	-samsung,color-depth:
+		number of bits per colour component.
+			COLOR_6 = 0, COLOR_8 = 1, COLOR_10 = 2, COLOR_12 = 3
+	-samsung,link-rate:
+		link rate supported by the panel.
+			LINK_RATE_1_62GBPS = 0x6, LINK_RATE_2_70GBPS = 0x0A
+	-samsung,lane-count:
+		number of lanes supported by the panel.
+			LANE_COUNT1 = 1, LANE_COUNT2 = 2, LANE_COUNT4 = 4
+	- display-timings: timings for the connected panel as described by
+		Documentation/devicetree/bindings/display/display-timing.txt
+
+Optional properties for dp-controller:
+	-interlaced:
+		interlace scan mode.
+			Progressive if defined, Interlaced if not defined
+	-vsync-active-high:
+		VSYNC polarity configuration.
+			High if defined, Low if not defined
+	-hsync-active-high:
+		HSYNC polarity configuration.
+			High if defined, Low if not defined
+	-samsung,hpd-gpio:
+		Hotplug detect GPIO.
+			Indicates which GPIO should be used for hotplug
+			detection
+	-video interfaces: Device node can contain video interface port
+			    nodes according to [1].
+
+[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+
+SOC specific portion:
+	dp-controller {
+		compatible = "samsung,exynos5-dp";
+		reg = <0x145b0000 0x10000>;
+		interrupts = <10 3>;
+		interrupt-parent = <&combiner>;
+		clocks = <&clock 342>;
+		clock-names = "dp";
+
+		phys = <&dp_phy>;
+		phy-names = "dp";
+	};
+
+Board Specific portion:
+	dp-controller {
+		samsung,color-space = <0>;
+		samsung,dynamic-range = <0>;
+		samsung,ycbcr-coeff = <0>;
+		samsung,color-depth = <1>;
+		samsung,link-rate = <0x0a>;
+		samsung,lane-count = <4>;
+
+		display-timings {
+			native-mode = <&lcd_timing>;
+			lcd_timing: 1366x768 {
+				clock-frequency = <70589280>;
+				hactive = <1366>;
+				vactive = <768>;
+				hfront-porch = <40>;
+				hback-porch = <40>;
+				hsync-len = <32>;
+				vback-porch = <10>;
+				vfront-porch = <12>;
+				vsync-len = <6>;
+			};
+		};
+
+		ports {
+			port@0 {
+				dp_out: endpoint {
+					remote-endpoint = <&bridge_in>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt
new file mode 100644
index 000000000000..0e6f0c024858
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt
@@ -0,0 +1,103 @@
+Exynos MIPI DSI Master
+
+Required properties:
+  - compatible: value should be one of the following
+		"samsung,exynos3250-mipi-dsi" /* for Exynos3250/3472 SoCs */
+		"samsung,exynos4210-mipi-dsi" /* for Exynos4 SoCs */
+		"samsung,exynos4415-mipi-dsi" /* for Exynos4415 SoC */
+		"samsung,exynos5410-mipi-dsi" /* for Exynos5410/5420/5440 SoCs */
+		"samsung,exynos5433-mipi-dsi" /* for Exynos5433 SoCs */
+  - reg: physical base address and length of the registers set for the device
+  - interrupts: should contain DSI interrupt
+  - clocks: list of clock specifiers, must contain an entry for each required
+    entry in clock-names
+  - clock-names: should include "bus_clk"and "sclk_mipi" entries
+		 the use of "pll_clk" is deprecated
+  - phys: list of phy specifiers, must contain an entry for each required
+    entry in phy-names
+  - phy-names: should include "dsim" entry
+  - vddcore-supply: MIPI DSIM Core voltage supply (e.g. 1.1V)
+  - vddio-supply: MIPI DSIM I/O and PLL voltage supply (e.g. 1.8V)
+  - samsung,pll-clock-frequency: specifies frequency of the oscillator clock
+  - #address-cells, #size-cells: should be set respectively to <1> and <0>
+    according to DSI host bindings (see MIPI DSI bindings [1])
+
+Optional properties:
+  - power-domains: a phandle to DSIM power domain node
+
+Child nodes:
+  Should contain DSI peripheral nodes (see MIPI DSI bindings [1]).
+
+Video interfaces:
+  Device node can contain video interface port nodes according to [2].
+  The following are properties specific to those nodes:
+
+  port node inbound:
+    - reg: (required) must be 0.
+  port node outbound:
+    - reg: (required) must be 1.
+
+  endpoint node connected from mic node (reg = 0):
+    - remote-endpoint: specifies the endpoint in mic node. This node is required
+		       for Exynos5433 mipi dsi. So mic can access to panel node
+		       thoughout this dsi node.
+  endpoint node connected to panel node (reg = 1):
+    - remote-endpoint: specifies the endpoint in panel node. This node is
+		       required in all kinds of exynos mipi dsi to represent
+		       the connection between mipi dsi and panel.
+    - samsung,burst-clock-frequency: specifies DSI frequency in high-speed burst
+      mode
+    - samsung,esc-clock-frequency: specifies DSI frequency in escape mode
+
+[1]: Documentation/devicetree/bindings/display/mipi-dsi-bus.txt
+[2]: Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+
+	dsi@11C80000 {
+		compatible = "samsung,exynos4210-mipi-dsi";
+		reg = <0x11C80000 0x10000>;
+		interrupts = <0 79 0>;
+		clocks = <&clock 286>, <&clock 143>;
+		clock-names = "bus_clk", "sclk_mipi";
+		phys = <&mipi_phy 1>;
+		phy-names = "dsim";
+		vddcore-supply = <&vusb_reg>;
+		vddio-supply = <&vmipi_reg>;
+		power-domains = <&pd_lcd0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		samsung,pll-clock-frequency = <24000000>;
+
+		panel@1 {
+			reg = <0>;
+			...
+			port {
+				panel_ep: endpoint {
+					remote-endpoint = <&dsi_ep>;
+				};
+			};
+		};
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				decon_to_mic: endpoint {
+					remote-endpoint = <&mic_to_decon>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				dsi_ep: endpoint {
+					reg = <0>;
+					samsung,burst-clock-frequency = <500000000>;
+					samsung,esc-clock-frequency = <20000000>;
+					remote-endpoint = <&panel_ep>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt b/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt
new file mode 100644
index 000000000000..1fd8cf9cbfac
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt
@@ -0,0 +1,43 @@
+Device-Tree bindings for drm hdmi driver
+
+Required properties:
+- compatible: value should be one among the following:
+	1) "samsung,exynos5-hdmi" <DEPRECATED>
+	2) "samsung,exynos4210-hdmi"
+	3) "samsung,exynos4212-hdmi"
+	4) "samsung,exynos5420-hdmi"
+- reg: physical base address of the hdmi and length of memory mapped
+	region.
+- interrupts: interrupt number to the cpu.
+- hpd-gpio: following information about the hotplug gpio pin.
+	a) phandle of the gpio controller node.
+	b) pin number within the gpio controller.
+	c) optional flags and pull up/down.
+- clocks: list of clock IDs from SoC clock driver.
+	a) hdmi: Gate of HDMI IP bus clock.
+	b) sclk_hdmi: Gate of HDMI special clock.
+	c) sclk_pixel: Pixel special clock, one of the two possible inputs of
+		HDMI clock mux.
+	d) sclk_hdmiphy: HDMI PHY clock output, one of two possible inputs of
+		HDMI clock mux.
+	e) mout_hdmi: It is required by the driver to switch between the 2
+		parents i.e. sclk_pixel and sclk_hdmiphy. If hdmiphy is stable
+		after configuration, parent is set to sclk_hdmiphy else
+		sclk_pixel.
+- clock-names: aliases as per driver requirements for above clock IDs:
+	"hdmi", "sclk_hdmi", "sclk_pixel", "sclk_hdmiphy" and "mout_hdmi".
+- ddc: phandle to the hdmi ddc node
+- phy: phandle to the hdmi phy node
+- samsung,syscon-phandle: phandle for system controller node for PMU.
+
+Example:
+
+	hdmi {
+		compatible = "samsung,exynos4212-hdmi";
+		reg = <0x14530000 0x100000>;
+		interrupts = <0 95 0>;
+		hpd-gpio = <&gpx3 7 1>;
+		ddc = <&hdmi_ddc_node>;
+		phy = <&hdmi_phy_node>;
+		samsung,syscon-phandle = <&pmu_system_controller>;
+	};
diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_hdmiddc.txt b/Documentation/devicetree/bindings/display/exynos/exynos_hdmiddc.txt
new file mode 100644
index 000000000000..41eee971562b
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/exynos/exynos_hdmiddc.txt
@@ -0,0 +1,15 @@
+Device-Tree bindings for hdmiddc driver
+
+Required properties:
+- compatible: value should be one of the following
+	1) "samsung,exynos5-hdmiddc" <DEPRECATED>
+	2) "samsung,exynos4210-hdmiddc"
+
+- reg: I2C address of the hdmiddc device.
+
+Example:
+
+	hdmiddc {
+		compatible = "samsung,exynos4210-hdmiddc";
+		reg = <0x50>;
+	};
diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_hdmiphy.txt b/Documentation/devicetree/bindings/display/exynos/exynos_hdmiphy.txt
new file mode 100644
index 000000000000..162f641f7639
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/exynos/exynos_hdmiphy.txt
@@ -0,0 +1,15 @@
+Device-Tree bindings for hdmiphy driver
+
+Required properties:
+- compatible: value should be one of the following:
+	1) "samsung,exynos5-hdmiphy" <DEPRECATED>
+	2) "samsung,exynos4210-hdmiphy".
+	3) "samsung,exynos4212-hdmiphy".
+- reg: I2C address of the hdmiphy device.
+
+Example:
+
+	hdmiphy {
+		compatible = "samsung,exynos4210-hdmiphy";
+		reg = <0x38>;
+	};
diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_mixer.txt b/Documentation/devicetree/bindings/display/exynos/exynos_mixer.txt
new file mode 100644
index 000000000000..3e38128f866b
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/exynos/exynos_mixer.txt
@@ -0,0 +1,26 @@
+Device-Tree bindings for mixer driver
+
+Required properties:
+- compatible: value should be one of the following:
+	1) "samsung,exynos5-mixer" <DEPRECATED>
+	2) "samsung,exynos4210-mixer"
+	3) "samsung,exynos4212-mixer"
+	4) "samsung,exynos5250-mixer"
+	5) "samsung,exynos5420-mixer"
+
+- reg: physical base address of the mixer and length of memory mapped
+	region.
+- interrupts: interrupt number to the cpu.
+- clocks: list of clock IDs from SoC clock driver.
+	a) mixer: Gate of Mixer IP bus clock.
+	b) sclk_hdmi: HDMI Special clock, one of the two possible inputs of
+               mixer mux.
+	c) hdmi: Gate of HDMI IP bus clock, needed together with sclk_hdmi.
+
+Example:
+
+	mixer {
+		compatible = "samsung,exynos5250-mixer";
+		reg = <0x14450000 0x10000>;
+		interrupts = <0 94 0>;
+	};
diff --git a/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt b/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt
new file mode 100644
index 000000000000..27c3ce0db16a
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt
@@ -0,0 +1,110 @@
+Device-Tree bindings for Samsung SoC display controller (FIMD)
+
+FIMD (Fully Interactive Mobile Display) is the Display Controller for the
+Samsung series of SoCs which transfers the image data from a video memory
+buffer to an external LCD interface.
+
+Required properties:
+- compatible: value should be one of the following
+		"samsung,s3c2443-fimd"; /* for S3C24XX SoCs */
+		"samsung,s3c6400-fimd"; /* for S3C64XX SoCs */
+		"samsung,s5pv210-fimd"; /* for S5PV210 SoC */
+		"samsung,exynos3250-fimd"; /* for Exynos3250/3472 SoCs */
+		"samsung,exynos4210-fimd"; /* for Exynos4 SoCs */
+		"samsung,exynos4415-fimd"; /* for Exynos4415 SoC */
+		"samsung,exynos5250-fimd"; /* for Exynos5 SoCs */
+
+- reg: physical base address and length of the FIMD registers set.
+
+- interrupt-parent: should be the phandle of the fimd controller's
+		parent interrupt controller.
+
+- interrupts: should contain a list of all FIMD IP block interrupts in the
+		 order: FIFO Level, VSYNC, LCD_SYSTEM. The interrupt specifier
+		 format depends on the interrupt controller used.
+
+- interrupt-names: should contain the interrupt names: "fifo", "vsync",
+	"lcd_sys", in the same order as they were listed in the interrupts
+        property.
+
+- pinctrl-0: pin control group to be used for this controller.
+
+- pinctrl-names: must contain a "default" entry.
+
+- clocks: must include clock specifiers corresponding to entries in the
+         clock-names property.
+
+- clock-names: list of clock names sorted in the same order as the clocks
+               property. Must contain "sclk_fimd" and "fimd".
+
+Optional Properties:
+- power-domains: a phandle to FIMD power domain node.
+- samsung,invert-vden: video enable signal is inverted
+- samsung,invert-vclk: video clock signal is inverted
+- display-timings: timing settings for FIMD, as described in document [1].
+		Can be used in case timings cannot be provided otherwise
+		or to override timings provided by the panel.
+- samsung,sysreg: handle to syscon used to control the system registers
+- i80-if-timings: timing configuration for lcd i80 interface support.
+  - cs-setup: clock cycles for the active period of address signal is enabled
+              until chip select is enabled.
+              If not specified, the default value(0) will be used.
+  - wr-setup: clock cycles for the active period of CS signal is enabled until
+              write signal is enabled.
+              If not specified, the default value(0) will be used.
+  - wr-active: clock cycles for the active period of CS is enabled.
+               If not specified, the default value(1) will be used.
+  - wr-hold: clock cycles for the active period of CS is disabled until write
+             signal is disabled.
+             If not specified, the default value(0) will be used.
+
+  The parameters are defined as:
+
+    VCLK(internal)  __|??????|_____|??????|_____|??????|_____|??????|_____|??
+                      :            :            :            :            :
+    Address Output  --:<XXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XX
+                      | cs-setup+1 |            :            :            :
+                      |<---------->|            :            :            :
+    Chip Select     ???????????????|____________:____________:____________|??
+                                   | wr-setup+1 |            | wr-hold+1  |
+                                   |<---------->|            |<---------->|
+    Write Enable    ????????????????????????????|____________|???????????????
+                                                | wr-active+1|
+                                                |<---------->|
+    Video Data      ----------------------------<XXXXXXXXXXXXXXXXXXXXXXXXX>--
+
+The device node can contain 'port' child nodes according to the bindings defined
+in [2]. The following are properties specific to those nodes:
+- reg: (required) port index, can be:
+		0 - for CAMIF0 input,
+		1 - for CAMIF1 input,
+		2 - for CAMIF2 input,
+		3 - for parallel output,
+		4 - for write-back interface
+
+[1]: Documentation/devicetree/bindings/display/display-timing.txt
+[2]: Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+
+SoC specific DT entry:
+
+	fimd@11c00000 {
+		compatible = "samsung,exynos4210-fimd";
+		interrupt-parent = <&combiner>;
+		reg = <0x11c00000 0x20000>;
+		interrupt-names = "fifo", "vsync", "lcd_sys";
+		interrupts = <11 0>, <11 1>, <11 2>;
+		clocks = <&clock 140>, <&clock 283>;
+		clock-names = "sclk_fimd", "fimd";
+		power-domains = <&pd_lcd0>;
+		status = "disabled";
+	};
+
+Board specific DT entry:
+
+	fimd@11c00000 {
+		pinctrl-0 = <&lcd_clk &lcd_data24 &pwm1_out>;
+		pinctrl-names = "default";
+		status = "okay";
+	};