Merge tag 'soc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull late ARM soc platform updates from Olof Johansson:
 "This branch contains updates to OMAP and Marvell platforms (kirkwood,
  dove, mvebu) that came in after we had done the big multiplatform
  merges, so they were kept separate from the rest, and not separated
  into the traditional topics of cleanup/driver/platform features.

  For OMAP, the updates are:
   - Runtime PM conversions for the GPMC and RNG IP blocks
   - Preparation patches for the OMAP common clock framework conversion
   - clkdev alias additions required by other drivers
   - Performance Monitoring Unit (PMU) support for OMAP2, 3, and
     non-4430 OMAP4
   - OMAP hwmod code and data improvements
   - Preparation patches for the IOMMU runtime PM conversion
   - Preparation patches for OMAP4 full-chip retention support

  For Kirkwood/Dove/mvebu:
   - New driver for "address decoder controller" for mvebu, which is a
     piece of hardware that configures addressable devices and
     peripherals.  First user is the boot rom aperture on armada XP
     since it is needed for SMP support.
   - New device tree bindings for peripherals such as gpio-fan, iconnect
     nand, mv_cesa and the above address decoder controller.
   - Some defconfig updates, mostly to enable new DT boards and a few
     drivers.
   - New drivers using the pincontrol subsystem for dove, kirkwood and
     mvebu
   - New clean gpio driver for mvebu"

* tag 'soc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (98 commits)
  ARM: mvebu: fix build breaks from multi-platform conversion
  ARM: OMAP4460/4470: PMU: Enable PMU for OMAP4460/70
  ARM: OMAP2+: PMU: Add runtime PM support
  ARM: OMAP4430: PMU: prepare to create PMU device via HWMOD
  ARM: OMAP2+: PMU: Convert OMAP2/3 devices to use HWMOD
  ARM: OMAP3: hwmod data: Add debugss HWMOD data
  ARM: OMAP2+: clockdomain/hwmod: add workaround for EMU clockdomain idle problems
  ARM: OMAP: Add a timer attribute for timers that can interrupt the DSP
  hwrng: OMAP: remove SoC restrictions from driver registration
  ARM: OMAP: split OMAP1, OMAP2+ RNG device registration
  hwrng: OMAP: convert to use runtime PM
  hwrng: OMAP: store per-device data in per-device variables, not file statics
  ARM: OMAP2xxx: hwmod/CM: add RNG integration data
  ARM: OMAP2+: gpmc: minimal driver support
  ARM: OMAP2+: gpmc: Adapt to HWMOD
  ARM: OMAP2/3: hwmod data: add gpmc
  ARM: OMAP4: hwmod data: add mmu hwmod for ipu and dsp
  ARM: OMAP3: hwmod data: add mmu data for iva and isp
  ARM: OMAP: iommu: fix including iommu.h without IOMMU_API selected
  ARM: OMAP4: hwmod data: add missing HWMOD_NO_IDLEST flags to some PRCM IP blocks
  ...

2 files changed, 78 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/gpio/gpio-fan.txt b/Documentation/devicetree/bindings/gpio/gpio-fan.txt
new file mode 100644
index 000000000000..2dd457a3469a
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-fan.txt
@@ -0,0 +1,25 @@
+Bindings for fan connected to GPIO lines
+
+Required properties:
+- compatible : "gpio-fan"
+- gpios: Specifies the pins that map to bits in the control value,
+  ordered MSB-->LSB.
+- gpio-fan,speed-map: A mapping of possible fan RPM speeds and the
+  control value that should be set to achieve them. This array
+  must have the RPM values in ascending order.
+
+Optional properties:
+- alarm-gpios: This pin going active indicates something is wrong with
+  the fan, and a udev event will be fired.
+
+Examples:
+
+	gpio_fan {
+		compatible = "gpio-fan";
+		gpios = <&gpio1 14 1
+			 &gpio1 13 1>;
+		gpio-fan,speed-map = <0    0
+				      3000 1
+				      6000 2>;
+		alarm-gpios = <&gpio1 15 1>;
+	};
diff --git a/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt b/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt
new file mode 100644
index 000000000000..a6f3bec1da7d
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt
@@ -0,0 +1,53 @@
+* Marvell EBU GPIO controller
+
+Required properties:
+
+- compatible : Should be "marvell,orion-gpio", "marvell,mv78200-gpio"
+  or "marvell,armadaxp-gpio". "marvell,orion-gpio" should be used for
+  Orion, Kirkwood, Dove, Discovery (except MV78200) and Armada
+  370. "marvell,mv78200-gpio" should be used for the Discovery
+  MV78200. "marvel,armadaxp-gpio" should be used for all Armada XP
+  SoCs (MV78230, MV78260, MV78460).
+
+- reg: Address and length of the register set for the device. Only one
+  entry is expected, except for the "marvell,armadaxp-gpio" variant
+  for which two entries are expected: one for the general registers,
+  one for the per-cpu registers.
+
+- interrupts: The list of interrupts that are used for all the pins
+  managed by this GPIO bank. There can be more than one interrupt
+  (example: 1 interrupt per 8 pins on Armada XP, which means 4
+  interrupts per bank of 32 GPIOs).
+
+- interrupt-controller: identifies the node as an interrupt controller
+
+- #interrupt-cells: specifies the number of cells needed to encode an
+  interrupt source. Should be two.
+  The first cell is the GPIO number.
+  The second cell is used to specify flags:
+    bits[3:0] trigger type and level flags:
+      1 = low-to-high edge triggered.
+      2 = high-to-low edge triggered.
+      4 = active high level-sensitive.
+      8 = active low level-sensitive.
+
+- gpio-controller: marks the device node as a gpio controller
+
+- ngpios: number of GPIOs this controller has
+
+- #gpio-cells: Should be two. The first cell is the pin number. The
+  second cell is reserved for flags, unused at the moment.
+
+Example:
+
+		gpio0: gpio@d0018100 {
+			compatible = "marvell,armadaxp-gpio";
+			reg = <0xd0018100 0x40>,
+			    <0xd0018800 0x30>;
+			ngpios = <32>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <16>, <17>, <18>, <19>;
+		};