Merge tag 'mmc-updates-for-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc

Pull MMC updates from Chris Ball:
 "MMC highlights for 3.8:

  Core:
   - Expose access to the eMMC RPMB ("Replay Protected Memory Block")
     area by extending the existing mmc_block ioctl.
   - Add SDIO powered-suspend DT properties to the core MMC DT binding.
   - Add no-1-8-v DT flag for boards where the SD controller reports
     that it supports 1.8V but the board itself has no way to switch to
     1.8V.
   - More work on switching to 1.8V UHS support using a vqmmc regulator.
   - Fix up a case where the slot-gpio helper may fail to reset the host
     controller properly if a card was removed during a transfer.
   - Fix several cases where a broken device could cause an infinite
     loop while we wait for a register to update.

  Drivers:
   - at91-mci: Remove obsolete driver, atmel-mci handles these devices
     now.
   - sdhci-dove: Allow using GPIOs for card-detect notifications.
   - sdhci-esdhc: Fix for recovering from ADMA errors on broken silicon.
   - sdhci-s3c: Add pinctrl support.
   - wmt-sdmmc: New driver for WonderMedia SD/MMC controllers."

* tag 'mmc-updates-for-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (65 commits)
  mmc: sdhci: implement the .card_event() method
  mmc: extend the slot-gpio card-detection to use host's .card_event() method
  mmc: add a card-event host operation
  mmc: sdhci-s3c: Fix compilation warning
  mmc: sdhci-pci: Enable SDHCI_CAN_DO_HISPD for Ricoh SDHCI controller
  mmc: sdhci-dove: allow GPIOs to be used for card detection on Dove
  mmc: sdhci-dove: use two-stage initialization for sdhci-pltfm
  mmc: sdhci-dove: use devm_clk_get()
  mmc: eSDHC: Recover from ADMA errors
  mmc: dw_mmc: remove duplicated buswidth code
  mmc: dw_mmc: relocate where dw_mci_setup_bus() is called from
  mmc: Limit MMC speed to 52MHz if not HS200
  mmc: dw_mmc: use devres functions in dw_mmc
  mmc: sh_mmcif: remove unneeded clock connection ID
  mmc: sh_mobile_sdhi: remove unneeded clock connection ID
  mmc: sh_mobile_sdhi: fix clock frequency printing
  mmc: Remove redundant null check before kfree in bus.c
  mmc: Remove redundant null check before kfree in sdio_bus.c
  mmc: sdhci-imx-esdhc: use more devm_* functions
  mmc: dt: add no-1-8-v device tree flag
  ...

1 files changed, 8 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt
index 8e2e0ba2f486..a591c6741d75 100644
--- a/Documentation/devicetree/bindings/mmc/mmc.txt
+++ b/Documentation/devicetree/bindings/mmc/mmc.txt
@@ -21,6 +21,12 @@ Optional properties:
 - cd-inverted: when present, polarity on the cd gpio line is inverted
 - wp-inverted: when present, polarity on the wp gpio line is inverted
 - max-frequency: maximum operating clock frequency
+- no-1-8-v: when present, denotes that 1.8v card voltage is not supported on
+  this system, even if the controller claims it is.
+
+Optional SDIO properties:
+- keep-power-in-suspend: Preserves card power during a suspend/resume cycle
+- enable-sdio-wakeup: Enables wake up of host system on SDIO IRQ assertion
 
 Example:
 
@@ -33,4 +39,6 @@ sdhci@ab000000 {
 	cd-inverted;
 	wp-gpios = <&gpio 70 0>;
 	max-frequency = <50000000>;
+	keep-power-in-suspend;
+	enable-sdio-wakeup;
 }