Merge tag 'spi-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi

Pull spi updates from Mark Brown:
 "The main focus of this release from a framework point of view has been
  spi-mem where we've acquired support for a few new hardware features
  which enable better performance on suitable hardware.

  Otherwise mostly thanks to Arnd's cleanup efforts on old platforms
  we've removed several obsolete drivers which just about balance out
  the newer drivers we've added this cycle.

  Summary:

   - Allow drivers to flag if they are unidirectional.

   - Support for DTR mode and hardware acceleration of dummy cycles in
     spi-mem.

   - Support for Allwinder H616, Intel Lightning Mountain, nVidia Tegra
     QuadSPI, Realtek RTL838x and RTL839x.

   - Removal of obsolete EFM32, Txx9 and SIRF Prima and Atlas drivers"

* tag 'spi-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (76 commits)
  spi: Skip zero-length transfers in spi_transfer_one_message()
  spi: dw: Avoid stack content exposure
  spi: cadence-quadspi: Use spi_mem_dtr_supports_op()
  spi: spi-mem: add spi_mem_dtr_supports_op()
  spi: atmel-quadspi: Disable the QSPI IP at suspend()
  spi: pxa2xx: Add IDs for the controllers found on Intel Lynxpoint
  spi: pxa2xx: Fix the controller numbering for Wildcat Point
  spi: Change provied to provided in the file spi.h
  spi: mediatek: add set_cs_timing support
  spi: support CS timing for HW & SW mode
  spi: add power control when set_cs_timing
  spi: stm32: make spurious and overrun interrupts visible
  spi: stm32h7: replace private SPI_1HZ_NS with NSEC_PER_SEC
  spi: stm32: defer probe for reset
  spi: stm32: driver uses reset controller only at init
  spi: stm32h7: ensure message are smaller than max size
  spi: stm32: use bitfield macros
  spi: stm32: do not mandate cs_gpio
  spi: stm32: properly handle 0 byte transfer
  spi: clps711xx: remove redundant white-space
  ...

1 files changed, 0 insertions, 67 deletions

diff --git a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt b/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt
deleted file mode 100644
index 945be7d5b236..000000000000
--- a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt
+++ /dev/null
@@ -1,67 +0,0 @@
-* Cadence Quad SPI controller
-
-Required properties:
-- compatible : should be one of the following:
-	Generic default - "cdns,qspi-nor".
-	For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor".
-	For TI AM654 SoC  - "ti,am654-ospi", "cdns,qspi-nor".
-- reg : Contains two entries, each of which is a tuple consisting of a
-	physical address and length. The first entry is the address and
-	length of the controller register set. The second entry is the
-	address and length of the QSPI Controller data area.
-- interrupts : Unit interrupt specifier for the controller interrupt.
-- clocks : phandle to the Quad SPI clock.
-- cdns,fifo-depth : Size of the data FIFO in words.
-- cdns,fifo-width : Bus width of the data FIFO in bytes.
-- cdns,trigger-address : 32-bit indirect AHB trigger address.
-
-Optional properties:
-- cdns,is-decoded-cs : Flag to indicate whether decoder is used or not.
-- cdns,rclk-en : Flag to indicate that QSPI return clock is used to latch
-  the read data rather than the QSPI clock. Make sure that QSPI return
-  clock is populated on the board before using this property.
-
-Optional subnodes:
-Subnodes of the Cadence Quad SPI controller are spi slave nodes with additional
-custom properties:
-- cdns,read-delay : Delay for read capture logic, in clock cycles
-- cdns,tshsl-ns : Delay in nanoseconds for the length that the master
-                  mode chip select outputs are de-asserted between
-		  transactions.
-- cdns,tsd2d-ns : Delay in nanoseconds between one chip select being
-                  de-activated and the activation of another.
-- cdns,tchsh-ns : Delay in nanoseconds between last bit of current
-                  transaction and deasserting the device chip select
-		  (qspi_n_ss_out).
-- cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low
-                  and first bit transfer.
-- resets	: Must contain an entry for each entry in reset-names.
-		  See ../reset/reset.txt for details.
-- reset-names	: Must include either "qspi" and/or "qspi-ocp".
-
-Example:
-
-	qspi: spi@ff705000 {
-		compatible = "cdns,qspi-nor";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0xff705000 0x1000>,
-		      <0xffa00000 0x1000>;
-		interrupts = <0 151 4>;
-		clocks = <&qspi_clk>;
-		cdns,is-decoded-cs;
-		cdns,fifo-depth = <128>;
-		cdns,fifo-width = <4>;
-		cdns,trigger-address = <0x00000000>;
-		resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>;
-		reset-names = "qspi", "qspi-ocp";
-
-		flash0: n25q00@0 {
-			...
-			cdns,read-delay = <4>;
-			cdns,tshsl-ns = <50>;
-			cdns,tsd2d-ns = <50>;
-			cdns,tchsh-ns = <4>;
-			cdns,tslch-ns = <4>;
-		};
-	};