Merge tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC device tree changes from Arnd Bergmann:
 "A large part of the arm-soc patches are nowadays DT changes, adding
  support for new SoCs, boards and devices without changing kernel
  source.  The plan is still to move the devicetree files out of the
  kernel tree and reduce the amount of churn going on here, but we keep
  finding reasons to delay doing that.

  Changes are really all over the place, with little sticking out
  particularly.  We have contributions from a total of 116 people in
  this branch.

  Unfortunately, the size of this branch also causes a significant
  number of conflicts at the moment, typically when subsystem
  maintainers merge patches that change the driver at the same time as
  the dts files.  In most cases this could be avoided because the dts
  changes are supposed to be compatible in both ways, and we are asking
  everyone to send ARM dts changes through our tree only"

* tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (541 commits)
  dts: stmmac: Document the clocks property in the stmmac base document
  dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
  ARM: STi: stih41x: Add support for the FSM Serial Flash Controller
  ARM: STi: stih416: Add support for the FSM Serial Flash Controller
  ARM: tegra: fix Dalmore pinctrl configuration
  ARM: dts: keystone: use common "ti,keystone" compatible instead of -evm
  ARM: dts: k2hk-evm: set ubifs partition size for 512M NAND
  ARM: dts: Build all keystone dt blobs
  ARM: dts: keystone: Fix control register range for clktsip
  ARM: dts: keystone: Fix domain register range for clkfftc1
  ARM: dts: bcm28155-ap: leave camldo1 on to fix reboot
  ARM: dts: add bcm590xx pmu support and enable for bcm28155-ap
  ARM: dts: bcm21664: Add device tree files.
  ARM: DT: bcm21664: Device tree bindings
  ARM: efm32: properly namespace i2c location property
  ARM: efm32: fix unit address part in USART2 device nodes' names
  ARM: mvebu: Enable NAND controller in Armada 385-DB
  ARM: mvebu: Add support for NAND controller in Armada 38x SoC
  ARM: mvebu: Add the Core Divider clock to Armada 38x SoCs
  ARM: mvebu: Add a 2 GHz fixed-clock on Armada 38x SoCs
  ...

2 files changed, 93 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/reset/st,sti-powerdown.txt b/Documentation/devicetree/bindings/reset/st,sti-powerdown.txt
new file mode 100644
index 000000000000..5ab26b7e9d35
--- /dev/null
+++ b/Documentation/devicetree/bindings/reset/st,sti-powerdown.txt
@@ -0,0 +1,47 @@
+STMicroelectronics STi family Sysconfig Peripheral Powerdown Reset Controller
+=============================================================================
+
+This binding describes a reset controller device that is used to enable and
+disable on-chip peripheral controllers such as USB and SATA, using
+"powerdown" control bits found in the STi family SoC system configuration
+registers. These have been grouped together into a single reset controller
+device for convenience.
+
+The actual action taken when powerdown is asserted is hardware dependent.
+However, when asserted it may not be possible to access the hardware's
+registers and after an assert/deassert sequence the hardware's previous state
+may no longer be valid.
+
+Please refer to reset.txt in this directory for common reset
+controller binding usage.
+
+Required properties:
+- compatible: Should be "st,<chip>-powerdown"
+	ex: "st,stih415-powerdown", "st,stih416-powerdown"
+- #reset-cells: 1, see below
+
+example:
+
+	powerdown: powerdown-controller {
+		#reset-cells = <1>;
+		compatible = "st,stih415-powerdown";
+	};
+
+
+Specifying powerdown control of devices
+=======================================
+
+Device nodes should specify the reset channel required in their "resets"
+property, containing a phandle to the powerdown device node and an
+index specifying which channel to use, as described in reset.txt
+
+example:
+
+	usb1: usb@fe200000 {
+		resets	= <&powerdown STIH41X_USB1_POWERDOWN>;
+	};
+
+Macro definitions for the supported reset channels can be found in:
+
+include/dt-bindings/reset-controller/stih415-resets.h
+include/dt-bindings/reset-controller/stih416-resets.h
diff --git a/Documentation/devicetree/bindings/reset/st,sti-softreset.txt b/Documentation/devicetree/bindings/reset/st,sti-softreset.txt
new file mode 100644
index 000000000000..a8d3d3c25ca2
--- /dev/null
+++ b/Documentation/devicetree/bindings/reset/st,sti-softreset.txt
@@ -0,0 +1,46 @@
+STMicroelectronics STi family Sysconfig Peripheral SoftReset Controller
+=============================================================================
+
+This binding describes a reset controller device that is used to enable and
+disable on-chip peripheral controllers such as USB and SATA, using
+"softreset" control bits found in the STi family SoC system configuration
+registers.
+
+The actual action taken when softreset is asserted is hardware dependent.
+However, when asserted it may not be possible to access the hardware's
+registers and after an assert/deassert sequence the hardware's previous state
+may no longer be valid.
+
+Please refer to reset.txt in this directory for common reset
+controller binding usage.
+
+Required properties:
+- compatible: Should be "st,<chip>-softreset" example:
+	"st,stih415-softreset" or "st,stih416-softreset";
+- #reset-cells: 1, see below
+
+example:
+
+	softreset: softreset-controller {
+		#reset-cells = <1>;
+		compatible = "st,stih415-softreset";
+	};
+
+
+Specifying softreset control of devices
+=======================================
+
+Device nodes should specify the reset channel required in their "resets"
+property, containing a phandle to the softreset device node and an
+index specifying which channel to use, as described in reset.txt
+
+example:
+
+	ethernet0{
+		resets			= <&softreset STIH415_ETH0_SOFTRESET>;
+	};
+
+Macro definitions for the supported reset channels can be found in:
+
+include/dt-bindings/reset-controller/stih415-resets.h
+include/dt-bindings/reset-controller/stih416-resets.h