Merge branch 'goodix' into next

Merge several improvements to Goodix touchscreen driver:
- power management support
- configuration upload
- axis swapping and inversion

3 files changed, 24 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt
index f2455c50533d..120bc4971cf3 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt
@@ -11,6 +11,10 @@ Required properties:
       0 = active high
       1 = active low
 
+Optional properties:
+- little-endian : GPIO registers are used as little endian. If not
+                  present registers are used as big endian by default.
+
 Example:
 
 gpio0: gpio@1100 {
diff --git a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
index 8ba98eec765b..c98757a69110 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
@@ -13,6 +13,17 @@ Required properties:
  - interrupt-parent	: Interrupt controller to which the chip is connected
  - interrupts		: Interrupt to which the chip is connected
 
+Optional properties:
+
+ - irq-gpios		: GPIO pin used for IRQ. The driver uses the
+			  interrupt gpio pin as output to reset the device.
+ - reset-gpios		: GPIO pin used for reset
+
+ - touchscreen-inverted-x  : X axis is inverted (boolean)
+ - touchscreen-inverted-y  : Y axis is inverted (boolean)
+ - touchscreen-swapped-x-y : X and Y axis are swapped (boolean)
+                             (swapping is done after inverting the axis)
+
 Example:
 
 	i2c@00000000 {
@@ -23,6 +34,9 @@ Example:
 			reg = <0x5d>;
 			interrupt-parent = <&gpio>;
 			interrupts = <0 0>;
+
+			irq-gpios = <&gpio1 0 0>;
+			reset-gpios = <&gpio1 1 0>;
 		};
 
 		/* ... */
diff --git a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt
index f5a8ca29aff0..aeea50c84e92 100644
--- a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt
+++ b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt
@@ -8,6 +8,11 @@ Required properties:
 - phy-mode: See ethernet.txt file in the same directory
 - clocks: a pointer to the reference clock for this device.
 
+Optional properties:
+- tx-csum-limit: maximum mtu supported by port that allow TX checksum.
+  Value is presented in bytes. If not used, by default 1600B is set for
+  "marvell,armada-370-neta" and 9800B for others.
+
 Example:
 
 ethernet@d0070000 {
@@ -15,6 +20,7 @@ ethernet@d0070000 {
 	reg = <0xd0070000 0x2500>;
 	interrupts = <8>;
 	clocks = <&gate_clk 4>;
+	tx-csum-limit = <9800>
 	status = "okay";
 	phy = <&phy0>;
 	phy-mode = "rgmii-id";