Merge series "Extend regulator notification support" from Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>:

Extend regulator notification support

This series extends the regulator notification and error flag support.
Initial discussion on the topic can be found here:
https://lore.kernel.org/lkml/6046836e22b8252983f08d5621c35ececb97820d.camel@fi.rohmeurope.com/

In a nutshell - the series adds:

1. WARNING level events/error flags. (Patch 3)
  Current regulator 'ERROR' event notifications for over/under
  voltage, over current and over temperature are used to indicate
  condition where monitored entity is so badly "off" that it actually
  indicates a hardware error which can not be recovered. The most
  typical hanling for that is believed to be a (graceful)
  system-shutdown. Here we add set of 'WARNING' level flags to allow
  sending notifications to consumers before things are 'that badly off'
  so that consumer drivers can implement recovery-actions.
2. Device-tree properties for specifying limit values. (Patches 1, 5)
  Add limits for above mentioned 'ERROR' and 'WARNING' levels (which
  send notifications to consumers) and also for a 'PROTECTION' level
  (which will be used to immediately shut-down the regulator(s) W/O
  informing consumer drivers. Typically implemented by hardware).
  Property parsing is implemented in regulator core which then calls
  callback operations for limit setting from the IC drivers. A
  warning is emitted if protection is requested by device tree but the
  underlying IC does not support configuring requested protection.
3. Helpers which can be registered by IC. (Patch 4)
  Target is to avoid implementing IRQ handling and IRQ storm protection
  in each IC driver. (Many of the ICs implementin these IRQs do not allow
  masking or acking the IRQ but keep the IRQ asserted for the whole
  duration of problem keeping the processor in IRQ handling loop).
4. Emergency poweroff function (refactored out of the thermal_core to
  kernel/reboot.c) which is called if IC fires error IRQs but IC reading
  fails and given retry-count is exceeded. (Patches 2, 4)
  Please note that the mutex in the emergency shutdown was replaced by a
  simple atomic in order to allow call from any context.

The helper was attempted to be done so it could be used to implement
roughly same logic as is used in qcom-labibb regulator. This means
amongst other things a safety shut-down if IC registers are not readable.
Using these shut-down retry counters are optional. The idea is that the
helper could be also used by simpler ICs which do not provide status
register(s) which can be used to check if error is still active.

ICs which do not have such status register can simply omit the 'renable'
callback (and retry-counts etc) - and helper assumes the situation is Ok
and re-enables IRQ after given time period. If problem persists the
handler is ran again and another notification is sent - but at least the
delay allows processor to avoid IRQ loop.

Patch 7 takes this notification support in use at BD9576MUF.
Patch 8 is related to MFD change which is not really related to the RFC
here. It was added to this series in order to avoid potential conflicts.
Patch 9 adds a maintainers entry.

Changelog v10-RESEND:
   - rebased on v5.13-rc4
Changelog v10:
   - rebased on v5.13-rc2
   - Move rdev_*() print macros to the internal.h and use rdev_dbg()
     from irq_helpers.c
   - Export rdev_get_name() and move it from coupler.h to driver.h for
     others to use. (It was already in coupler.h but not exported -
     usage was limited and coupler.h does not sound like optimal place
     as rdev_name is not only used by coupled regulators)
   - Send all regulator notifications from irq_helpers.c at one OR'd
     event for the sake of simplicity. For BD9576 this does not matter
     as it has own IRQ for each event case. Header defining events says
     they may be OR'd.
   - Change WARN() at protection shutdown to pr_emerg as suggested by
     Petr.
Changelog v9:
   - rebases on v5.13-rc1
   - Update thermal documentation
   - Fix regulator notification event number
Changelog v8:
   - split shutdown API adding and thermal core taking it in use to
     own patches.
   - replace the spinlock with atomic when ensuring the emergency
     shutdown is only called once.
Changelog v7:
  general:
   - rebased on v5.12-rc7
   - new patch for refactoring the hw-failure reboot logic out of
     thermal_core.c for others to use.
  notification helpers:
   - fix regulator error_flags query
   - grammar/typos
   - do not BUG() but attempt to shut-down the system
   - use BITS_PER_TYPE()

Changelog v6:
  Add MAINTAINERS entry
  Changes to IRQ notifiers
   - move devm functions to drivers/regulator/devres.c
   - drop irq validity check
   - use devm_add_action_or_reset()
   - fix styling issues
   - fix kerneldocs

Changelog v5:
   - Fix the badly formatted pr_emerg() call.

Changelog v4:
   - rebased on v5.12-rc6
   - dropped RFC
   - fix external FET DT-binding.
   - improve prints for cases when expecting HW failure.
   - styling and typos

Changelog v3:
  Regulator core:
   - Fix dangling pointer access at regulator_irq_helper()
  stpmic1_regulator:
   - fix function prototype (compile error)
  bd9576-regulator:
   - Update over current limits to what was given in new data-sheet
     (REV00K)
   - Allow over-current monitoring without external FET. Set limits to
     values given in data-sheet (REV00K).

Changelog v2:
  Generic:
  - rebase on v5.12-rc2 + BD9576 series
  - Split devm variant of delayed wq to own series
  Regulator framework:
  - Provide non devm variant of IRQ notification helpers
  - shorten dt-property names as suggested by Rob
  - unconditionally call map_event in IRQ handling and require it to be
    populated
  BD9576 regulators:
  - change the FET resistance property to micro-ohms
  - fix voltage computation in OC limit setting

17 files changed, 110 insertions, 28 deletions

diff --git a/Documentation/devicetree/bindings/clock/idt,versaclock5.yaml b/Documentation/devicetree/bindings/clock/idt,versaclock5.yaml
index c268debe5b8d..28675b0b80f1 100644
--- a/Documentation/devicetree/bindings/clock/idt,versaclock5.yaml
+++ b/Documentation/devicetree/bindings/clock/idt,versaclock5.yaml
@@ -60,7 +60,6 @@ properties:
     maxItems: 2
 
   idt,xtal-load-femtofarads:
-    $ref: /schemas/types.yaml#/definitions/uint32
     minimum: 9000
     maximum: 22760
     description: Optional load capacitor for XTAL1 and XTAL2
@@ -84,7 +83,6 @@ patternProperties:
         enum: [ 1800000, 2500000, 3300000 ]
       idt,slew-percent:
         description: The Slew rate control for CMOS single-ended.
-        $ref: /schemas/types.yaml#/definitions/uint32
         enum: [ 80, 85, 90, 100 ]
 
 required:
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mpc.yaml b/Documentation/devicetree/bindings/i2c/i2c-mpc.yaml
index 7b553d559c83..98c6fcf7bf26 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-mpc.yaml
+++ b/Documentation/devicetree/bindings/i2c/i2c-mpc.yaml
@@ -46,6 +46,13 @@ properties:
     description: |
       I2C bus timeout in microseconds
 
+  fsl,i2c-erratum-a004447:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description: |
+      Indicates the presence of QorIQ erratum A-004447, which
+      says that the standard i2c recovery scheme mechanism does
+      not work and an alternate implementation is needed.
+
 required:
   - compatible
   - reg
diff --git a/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.yaml b/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.yaml
index 6f2398cdc82d..1e7894e524f9 100644
--- a/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.yaml
+++ b/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.yaml
@@ -102,7 +102,6 @@ patternProperties:
 
       st,adc-channel-names:
         description: List of single-ended channel names.
-        $ref: /schemas/types.yaml#/definitions/string-array
 
       st,filter-order:
         description: |
diff --git a/Documentation/devicetree/bindings/input/input.yaml b/Documentation/devicetree/bindings/input/input.yaml
index 74244d21d2b3..d41d8743aad4 100644
--- a/Documentation/devicetree/bindings/input/input.yaml
+++ b/Documentation/devicetree/bindings/input/input.yaml
@@ -38,6 +38,5 @@ properties:
       Duration in seconds which the key should be kept pressed for device to
       reset automatically. Device with key pressed reset feature can specify
       this property.
-    $ref: /schemas/types.yaml#/definitions/uint32
 
 additionalProperties: true
diff --git a/Documentation/devicetree/bindings/interconnect/qcom,rpmh.yaml b/Documentation/devicetree/bindings/interconnect/qcom,rpmh.yaml
index cb6498108b78..36c955965d90 100644
--- a/Documentation/devicetree/bindings/interconnect/qcom,rpmh.yaml
+++ b/Documentation/devicetree/bindings/interconnect/qcom,rpmh.yaml
@@ -92,7 +92,6 @@ properties:
       this interconnect to send RPMh commands.
 
   qcom,bcm-voter-names:
-    $ref: /schemas/types.yaml#/definitions/string-array
     description: |
       Names for each of the qcom,bcm-voters specified.
 
diff --git a/Documentation/devicetree/bindings/leds/leds-bcm6328.txt b/Documentation/devicetree/bindings/leds/leds-bcm6328.txt
index ccebce597f37..a555d94084b7 100644
--- a/Documentation/devicetree/bindings/leds/leds-bcm6328.txt
+++ b/Documentation/devicetree/bindings/leds/leds-bcm6328.txt
@@ -4,8 +4,8 @@ This controller is present on BCM6318, BCM6328, BCM6362 and BCM63268.
 In these SoCs it's possible to control LEDs both as GPIOs or by hardware.
 However, on some devices there are Serial LEDs (LEDs connected to a 74x164
 controller), which can either be controlled by software (exporting the 74x164
-as spi-gpio. See Documentation/devicetree/bindings/gpio/gpio-74x164.txt), or
-by hardware using this driver.
+as spi-gpio. See Documentation/devicetree/bindings/gpio/fairchild,74hc595.yaml),
+or by hardware using this driver.
 Some of these Serial LEDs are hardware controlled (e.g. ethernet LEDs) and
 exporting the 74x164 as spi-gpio prevents those LEDs to be hardware
 controlled, so the only chance to keep them working is by using this driver.
diff --git a/Documentation/devicetree/bindings/leds/leds-bcm6358.txt b/Documentation/devicetree/bindings/leds/leds-bcm6358.txt
index da5708e7b43b..6e51c6b91ee5 100644
--- a/Documentation/devicetree/bindings/leds/leds-bcm6358.txt
+++ b/Documentation/devicetree/bindings/leds/leds-bcm6358.txt
@@ -3,7 +3,7 @@ LEDs connected to Broadcom BCM6358 controller
 This controller is present on BCM6358 and BCM6368.
 In these SoCs there are Serial LEDs (LEDs connected to a 74x164 controller),
 which can either be controlled by software (exporting the 74x164 as spi-gpio.
-See Documentation/devicetree/bindings/gpio/gpio-74x164.txt), or
+See Documentation/devicetree/bindings/gpio/fairchild,74hc595.yaml), or
 by hardware using this driver.
 
 Required properties:
diff --git a/Documentation/devicetree/bindings/media/renesas,drif.yaml b/Documentation/devicetree/bindings/media/renesas,drif.yaml
index f1bdaeab4053..ce505a7c006a 100644
--- a/Documentation/devicetree/bindings/media/renesas,drif.yaml
+++ b/Documentation/devicetree/bindings/media/renesas,drif.yaml
@@ -99,32 +99,26 @@ properties:
       Indicates that the channel acts as primary among the bonded channels.
 
   port:
-    type: object
+    $ref: /schemas/graph.yaml#/properties/port
+    unevaluatedProperties: false
     description:
-      Child port node corresponding to the data input, in accordance with the
-      video interface bindings defined in
-      Documentation/devicetree/bindings/media/video-interfaces.txt.
-      The port node must contain at least one endpoint.
+      Child port node corresponding to the data input. The port node must
+      contain at least one endpoint.
 
     properties:
       endpoint:
-        type: object
+        $ref: /schemas/graph.yaml#/$defs/endpoint-base
+        unevaluatedProperties: false
 
         properties:
-          remote-endpoint:
-            description:
-              A phandle to the remote tuner endpoint subnode in remote node
-              port.
-
           sync-active:
+            $ref: /schemas/types.yaml#/definitions/uint32
             enum: [0, 1]
             description:
               Indicates sync signal polarity, 0/1 for low/high respectively.
               This property maps to SYNCAC bit in the hardware manual. The
               default is 1 (active high).
 
-        additionalProperties: false
-
 required:
   - compatible
   - reg
diff --git a/Documentation/devicetree/bindings/net/qcom,ipa.yaml b/Documentation/devicetree/bindings/net/qcom,ipa.yaml
index 7443490d4cc6..5fe6d3dceb08 100644
--- a/Documentation/devicetree/bindings/net/qcom,ipa.yaml
+++ b/Documentation/devicetree/bindings/net/qcom,ipa.yaml
@@ -105,7 +105,6 @@ properties:
       - description: Whether the IPA clock is enabled (if valid)
 
   qcom,smem-state-names:
-    $ref: /schemas/types.yaml#/definitions/string-array
     description: The names of the state bits used for SMP2P output
     items:
       - const: ipa-clock-enabled-valid
diff --git a/Documentation/devicetree/bindings/net/renesas,ether.yaml b/Documentation/devicetree/bindings/net/renesas,ether.yaml
index 8ce5ed8a58dd..c101a1ec846e 100644
--- a/Documentation/devicetree/bindings/net/renesas,ether.yaml
+++ b/Documentation/devicetree/bindings/net/renesas,ether.yaml
@@ -10,7 +10,7 @@ allOf:
   - $ref: ethernet-controller.yaml#
 
 maintainers:
-  - Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
+  - Sergei Shtylyov <sergei.shtylyov@gmail.com>
 
 properties:
   compatible:
diff --git a/Documentation/devicetree/bindings/nvmem/mtk-efuse.txt b/Documentation/devicetree/bindings/nvmem/mtk-efuse.txt
index d479ad977e24..b6791702bcfc 100644
--- a/Documentation/devicetree/bindings/nvmem/mtk-efuse.txt
+++ b/Documentation/devicetree/bindings/nvmem/mtk-efuse.txt
@@ -9,7 +9,6 @@ Required properties:
 	      "mediatek,mt8173-efuse" or "mediatek,efuse": for MT8173
 	      "mediatek,mt8192-efuse", "mediatek,efuse": for MT8192
 	      "mediatek,mt8516-efuse", "mediatek,efuse": for MT8516
-	      "mediatek,mt8192-efuse", "mediatek,efuse": for MT8192
 - reg: Should contain registers location and length
 
 = Data cells =
diff --git a/Documentation/devicetree/bindings/phy/phy-cadence-torrent.yaml b/Documentation/devicetree/bindings/phy/phy-cadence-torrent.yaml
index 01dcd14e7b2a..320a232c7208 100644
--- a/Documentation/devicetree/bindings/phy/phy-cadence-torrent.yaml
+++ b/Documentation/devicetree/bindings/phy/phy-cadence-torrent.yaml
@@ -118,7 +118,7 @@ patternProperties:
         description:
           Specifies the Spread Spectrum Clocking mode used. It can be NO_SSC,
           EXTERNAL_SSC or INTERNAL_SSC.
-          Refer include/dt-bindings/phy/phy-cadence-torrent.h for the constants to be used.
+          Refer include/dt-bindings/phy/phy-cadence.h for the constants to be used.
         $ref: /schemas/types.yaml#/definitions/uint32
         enum: [0, 1, 2]
         default: 0
diff --git a/Documentation/devicetree/bindings/power/supply/sc2731-charger.yaml b/Documentation/devicetree/bindings/power/supply/sc2731-charger.yaml
index db1aa238cda5..b62c2431f94e 100644
--- a/Documentation/devicetree/bindings/power/supply/sc2731-charger.yaml
+++ b/Documentation/devicetree/bindings/power/supply/sc2731-charger.yaml
@@ -20,7 +20,7 @@ properties:
     maxItems: 1
 
   phys:
-    $ref: /schemas/types.yaml#/definitions/phandle
+    maxItems: 1
     description: phandle to the USB phy
 
   monitored-battery:
diff --git a/Documentation/devicetree/bindings/regulator/regulator.yaml b/Documentation/devicetree/bindings/regulator/regulator.yaml
index 6d0bc9cd4040..a6ae9ecae5cc 100644
--- a/Documentation/devicetree/bindings/regulator/regulator.yaml
+++ b/Documentation/devicetree/bindings/regulator/regulator.yaml
@@ -117,6 +117,88 @@ properties:
     description: Enable over current protection.
     type: boolean
 
+  regulator-oc-protection-microamp:
+    description: Set over current protection limit. This is a limit where
+      hardware performs emergency shutdown. Zero can be passed to disable
+      protection and value '1' indicates that protection should be enabled but
+      limit setting can be omitted.
+
+  regulator-oc-error-microamp:
+    description: Set over current error limit. This is a limit where part of
+      the hardware propably is malfunctional and damage prevention is requested.
+      Zero can be passed to disable error detection and value '1' indicates
+      that detection should be enabled but limit setting can be omitted.
+
+  regulator-oc-warn-microamp:
+    description: Set over current warning limit. This is a limit where hardware
+      is assumed still to be functional but approaching limit where it gets
+      damaged. Recovery actions should be initiated. Zero can be passed to
+      disable detection and value '1' indicates that detection should
+      be enabled but limit setting can be omitted.
+
+  regulator-ov-protection-microvolt:
+    description: Set over voltage protection limit. This is a limit where
+      hardware performs emergency shutdown. Zero can be passed to disable
+      protection and value '1' indicates that protection should be enabled but
+      limit setting can be omitted. Limit is given as microvolt offset from
+      voltage set to regulator.
+
+  regulator-ov-error-microvolt:
+    description: Set over voltage error limit. This is a limit where part of
+      the hardware propably is malfunctional and damage prevention is requested
+      Zero can be passed to disable error detection and value '1' indicates
+      that detection should be enabled but limit setting can be omitted. Limit
+      is given as microvolt offset from voltage set to regulator.
+
+  regulator-ov-warn-microvolt:
+    description: Set over voltage warning limit. This is a limit where hardware
+      is assumed still to be functional but approaching limit where it gets
+      damaged. Recovery actions should be initiated. Zero can be passed to
+      disable detection and value '1' indicates that detection should
+      be enabled but limit setting can be omitted. Limit is given as microvolt
+      offset from voltage set to regulator.
+
+  regulator-uv-protection-microvolt:
+    description: Set over under voltage protection limit. This is a limit where
+      hardware performs emergency shutdown. Zero can be passed to disable
+      protection and value '1' indicates that protection should be enabled but
+      limit setting can be omitted. Limit is given as microvolt offset from
+      voltage set to regulator.
+
+  regulator-uv-error-microvolt:
+    description: Set under voltage error limit. This is a limit where part of
+      the hardware propably is malfunctional and damage prevention is requested
+      Zero can be passed to disable error detection and value '1' indicates
+      that detection should be enabled but limit setting can be omitted. Limit
+      is given as microvolt offset from voltage set to regulator.
+
+  regulator-uv-warn-microvolt:
+    description: Set over under voltage warning limit. This is a limit where
+      hardware is assumed still to be functional but approaching limit where
+      it gets damaged. Recovery actions should be initiated. Zero can be passed
+      to disable detection and value '1' indicates that detection should
+      be enabled but limit setting can be omitted. Limit is given as microvolt
+      offset from voltage set to regulator.
+
+  regulator-temp-protection-kelvin:
+    description: Set over temperature protection limit. This is a limit where
+      hardware performs emergency shutdown. Zero can be passed to disable
+      protection and value '1' indicates that protection should be enabled but
+      limit setting can be omitted.
+
+  regulator-temp-error-kelvin:
+    description: Set over temperature error limit. This is a limit where part of
+      the hardware propably is malfunctional and damage prevention is requested
+      Zero can be passed to disable error detection and value '1' indicates
+      that detection should be enabled but limit setting can be omitted.
+
+  regulator-temp-warn-kelvin:
+    description: Set over temperature warning limit. This is a limit where
+      hardware is assumed still to be functional but approaching limit where it
+      gets damaged. Recovery actions should be initiated. Zero can be passed to
+      disable detection and value '1' indicates that detection should
+      be enabled but limit setting can be omitted.
+
   regulator-active-discharge:
     description: |
       tristate, enable/disable active discharge of regulators. The values are:
diff --git a/Documentation/devicetree/bindings/regulator/rohm,bd9576-regulator.yaml b/Documentation/devicetree/bindings/regulator/rohm,bd9576-regulator.yaml
index b6515a0cee62..7cb74cc8c5d9 100644
--- a/Documentation/devicetree/bindings/regulator/rohm,bd9576-regulator.yaml
+++ b/Documentation/devicetree/bindings/regulator/rohm,bd9576-regulator.yaml
@@ -27,6 +27,12 @@ patternProperties:
       Properties for single regulator.
     $ref: "regulator.yaml#"
 
+    properties:
+      rohm,ocw-fet-ron-micro-ohms:
+        description: |
+          External FET's ON-resistance. Required if VoutS1 OCP/OCW is
+          to be set.
+
     required:
       - regulator-name
 
diff --git a/Documentation/devicetree/bindings/sound/fsl,rpmsg.yaml b/Documentation/devicetree/bindings/sound/fsl,rpmsg.yaml
index b4c190bddd84..61802a11baf4 100644
--- a/Documentation/devicetree/bindings/sound/fsl,rpmsg.yaml
+++ b/Documentation/devicetree/bindings/sound/fsl,rpmsg.yaml
@@ -49,7 +49,7 @@ properties:
     maxItems: 1
 
   memory-region:
-    $ref: /schemas/types.yaml#/definitions/phandle
+    maxItems: 1
     description:
       phandle to a node describing reserved memory (System RAM memory)
       The M core can't access all the DDR memory space on some platform,
diff --git a/Documentation/devicetree/bindings/spi/spi-mux.yaml b/Documentation/devicetree/bindings/spi/spi-mux.yaml
index d09c6355e22d..51c7622dc20b 100644
--- a/Documentation/devicetree/bindings/spi/spi-mux.yaml
+++ b/Documentation/devicetree/bindings/spi/spi-mux.yaml
@@ -72,7 +72,7 @@ examples:
 
             mux-controls = <&mux>;
 
-            spi-flash@0 {
+            flash@0 {
                 compatible = "jedec,spi-nor";
                 reg = <0>;
                 spi-max-frequency = <40000000>;