summaryrefslogtreecommitdiff
path: root/Documentation/devicetree
diff options
context:
space:
mode:
authorAnatolij Gustschin <agust@denx.de>2012-08-24 05:39:39 +0000
committerAnatolij Gustschin <agust@denx.de>2012-09-14 10:10:32 +0200
commit00e4b1975bbcd10445808cec0a3a1442e8deca53 (patch)
treefd966b7c3453a2d4a51aab505037c491ac003edf /Documentation/devicetree
parent56ebc06393e86cd3ffd66655c84df0146158d951 (diff)
dt/misc: add bindings documentation for ifm camera sensor interface
IFM O2D cameras use special sensor bus interface glue-logic to connect camera sensors to mpc5200 LocalPlus bus. Add device tree bindings documentation for it. Signed-off-by: Anatolij Gustschin <agust@denx.de>
Diffstat (limited to 'Documentation/devicetree')
-rw-r--r--Documentation/devicetree/bindings/misc/ifm-csi.txt41
1 files changed, 41 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/misc/ifm-csi.txt b/Documentation/devicetree/bindings/misc/ifm-csi.txt
new file mode 100644
index 000000000000..5bdfffb0b9f7
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/ifm-csi.txt
@@ -0,0 +1,41 @@
+IFM camera sensor interface on mpc5200 LocalPlus bus
+
+Required properties:
+- compatible: "ifm,o2d-csi"
+- reg: specifies sensor chip select number and associated address range
+- interrupts: external interrupt line number and interrupt sense mode
+ of the interrupt line signaling frame valid events
+- gpios: three gpio-specifiers for "capture", "reset" and "master enable"
+ GPIOs (strictly in this order).
+- ifm,csi-clk-handle: the phandle to a node in the DT describing the sensor
+ clock generator. This node is usually a general purpose timer controller.
+- ifm,csi-addr-bus-width: address bus width (valid values are 16, 24, 25)
+- ifm,csi-data-bus-width: data bus width (valid values are 8 and 16)
+- ifm,csi-wait-cycles: sensor bus wait cycles
+
+Optional properties:
+- ifm,csi-byte-swap: if this property is present, the byte swapping on
+ the bus will be enabled.
+
+Example:
+
+ csi@3,0 {
+ compatible = "ifm,o2d-csi";
+ reg = <3 0 0x00100000>; /* CS 3, 1 MiB range */
+ interrupts = <1 1 2>; /* IRQ1, edge falling */
+
+ ifm,csi-clk-handle = <&timer7>;
+ gpios = <&gpio_simple 23 0 /* image_capture */
+ &gpio_simple 26 0 /* image_reset */
+ &gpio_simple 29 0>; /* image_master_en */
+
+ ifm,csi-addr-bus-width = <24>;
+ ifm,csi-data-bus-width = <8>;
+ ifm,csi-wait-cycles = <0>;
+ };
+
+The base address of the used chip select is specified in the
+ranges property of the parent localbus node, for example:
+
+ ranges = <0 0 0xff000000 0x01000000
+ 3 0 0xe3000000 0x00100000>;