Merge branch 'staging/for_v3.4' into v4l_for_linus

* staging/for_v3.4: (10117 commits)
  [media] update CARDLIST.em28xx
  [media] partially reverts changeset fa5527c
  [media] stb0899: fix the limits for signal strength values
  [media] em28xx: support for 2304:0242 PCTV QuatroStick (510e)
  [media] em28xx: support for 2013:0251 PCTV QuatroStick nano (520e)
  [media] -EINVAL -> -ENOTTY
  [media] gspca - sn9c20x: Cleanup source
  [media] gspca - sn9c20x: Simplify register write for capture start/stop
  [media] gspca - sn9c20x: Add automatic JPEG compression mechanism
  [media] gspca - sn9c20x: Greater delay in case of sensor no response
  [media] gspca - sn9c20x: Optimize the code of write sequences
  [media] gspca - sn9c20x: Add the JPEG compression quality control
  [media] gspca - sn9c20x: Add a delay after Omnivision sensor reset
  [media] gspca - sn9c20x: Propagate USB errors to higher level
  [media] gspca - sn9c20x: Use the new video control mechanism
  [media] gspca - sn9c20x: Fix loss of frame start
  [media] gspca - zc3xx: Lack of register 08 value for sensor cs2102k
  [media] gspca - ov534_9: Add brightness to OmniVision 5621 sensor
  [media] gspca - zc3xx: Add V4L2_CID_JPEG_COMPRESSION_QUALITY control support
  [media] pvrusb2: fix 7MHz & 8MHz DVB-T tuner support for HVR1900 rev D1F5
  ...

7 files changed, 78 insertions, 27 deletions

diff --git a/Documentation/hwmon/it87 b/Documentation/hwmon/it87
index 6f496a586732..23b7def21ba8 100644
--- a/Documentation/hwmon/it87
+++ b/Documentation/hwmon/it87
@@ -26,6 +26,10 @@ Supported chips:
     Prefix: 'it8721'
     Addresses scanned: from Super I/O config space (8 I/O ports)
     Datasheet: Not publicly available
+  * IT8728F
+    Prefix: 'it8728'
+    Addresses scanned: from Super I/O config space (8 I/O ports)
+    Datasheet: Not publicly available
   * SiS950   [clone of IT8705F]
     Prefix: 'it87'
     Addresses scanned: from Super I/O config space (8 I/O ports)
@@ -71,7 +75,7 @@ Description
 -----------
 
 This driver implements support for the IT8705F, IT8712F, IT8716F,
-IT8718F, IT8720F, IT8721F, IT8726F, IT8758E and SiS950 chips.
+IT8718F, IT8720F, IT8721F, IT8726F, IT8728F, IT8758E and SiS950 chips.
 
 These chips are 'Super I/O chips', supporting floppy disks, infrared ports,
 joysticks and other miscellaneous stuff. For hardware monitoring, they
@@ -105,6 +109,9 @@ The IT8726F is just bit enhanced IT8716F with additional hardware
 for AMD power sequencing. Therefore the chip will appear as IT8716F
 to userspace applications.
 
+The IT8728F is considered compatible with the IT8721F, until a datasheet
+becomes available (hopefully.)
+
 Temperatures are measured in degrees Celsius. An alarm is triggered once
 when the Overtemperature Shutdown limit is crossed.
 
@@ -121,8 +128,8 @@ alarm is triggered if the voltage has crossed a programmable minimum or
 maximum limit. Note that minimum in this case always means 'closest to
 zero'; this is important for negative voltage measurements. All voltage
 inputs can measure voltages between 0 and 4.08 volts, with a resolution of
-0.016 volt (except IT8721F/IT8758E: 0.012 volt.) The battery voltage in8 does
-not have limit registers.
+0.016 volt (except IT8721F/IT8758E and IT8728F: 0.012 volt.) The battery
+voltage in8 does not have limit registers.
 
 On the IT8721F/IT8758E, some voltage inputs are internal and scaled inside
 the chip (in7, in8 and optionally in3). The driver handles this transparently
diff --git a/Documentation/hwmon/jc42 b/Documentation/hwmon/jc42
index a22ecf48f255..52729a756c1b 100644
--- a/Documentation/hwmon/jc42
+++ b/Documentation/hwmon/jc42
@@ -7,21 +7,29 @@ Supported chips:
     Addresses scanned: I2C 0x18 - 0x1f
     Datasheets:
 	http://www.analog.com/static/imported-files/data_sheets/ADT7408.pdf
-  * IDT TSE2002B3, TS3000B3
-    Prefix: 'tse2002b3', 'ts3000b3'
+  * Atmel AT30TS00
+    Prefix: 'at30ts00'
     Addresses scanned: I2C 0x18 - 0x1f
     Datasheets:
-	http://www.idt.com/products/getdoc.cfm?docid=18715691
-	http://www.idt.com/products/getdoc.cfm?docid=18715692
+	http://www.atmel.com/Images/doc8585.pdf
+  * IDT TSE2002B3, TSE2002GB2, TS3000B3, TS3000GB2
+    Prefix: 'tse2002', 'ts3000'
+    Addresses scanned: I2C 0x18 - 0x1f
+    Datasheets:
+	http://www.idt.com/sites/default/files/documents/IDT_TSE2002B3C_DST_20100512_120303152056.pdf
+	http://www.idt.com/sites/default/files/documents/IDT_TSE2002GB2A1_DST_20111107_120303145914.pdf
+	http://www.idt.com/sites/default/files/documents/IDT_TS3000B3A_DST_20101129_120303152013.pdf
+	http://www.idt.com/sites/default/files/documents/IDT_TS3000GB2A1_DST_20111104_120303151012.pdf
   * Maxim MAX6604
     Prefix: 'max6604'
     Addresses scanned: I2C 0x18 - 0x1f
     Datasheets:
 	http://datasheets.maxim-ic.com/en/ds/MAX6604.pdf
-  * Microchip MCP9805, MCP98242, MCP98243, MCP9843
-    Prefixes: 'mcp9805', 'mcp98242', 'mcp98243', 'mcp9843'
+  * Microchip MCP9804, MCP9805, MCP98242, MCP98243, MCP9843
+    Prefixes: 'mcp9804', 'mcp9805', 'mcp98242', 'mcp98243', 'mcp9843'
     Addresses scanned: I2C 0x18 - 0x1f
     Datasheets:
+	http://ww1.microchip.com/downloads/en/DeviceDoc/22203C.pdf
 	http://ww1.microchip.com/downloads/en/DeviceDoc/21977b.pdf
 	http://ww1.microchip.com/downloads/en/DeviceDoc/21996a.pdf
 	http://ww1.microchip.com/downloads/en/DeviceDoc/22153c.pdf
@@ -48,6 +56,12 @@ Supported chips:
     Datasheets:
 	http://www.st.com/stonline/products/literature/ds/13447/stts424.pdf
 	http://www.st.com/stonline/products/literature/ds/13448/stts424e02.pdf
+  * ST Microelectronics STTS2002, STTS3000
+    Prefix: 'stts2002', 'stts3000'
+    Addresses scanned: I2C 0x18 - 0x1f
+    Datasheets:
+	http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/DATASHEET/CD00225278.pdf
+	http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/DATA_BRIEF/CD00270920.pdf
   * JEDEC JC 42.4 compliant temperature sensor chips
     Prefix: 'jc42'
     Addresses scanned: I2C 0x18 - 0x1f
diff --git a/Documentation/hwmon/lm63 b/Documentation/hwmon/lm63
index b9843eab1afb..4d30d209881a 100644
--- a/Documentation/hwmon/lm63
+++ b/Documentation/hwmon/lm63
@@ -12,6 +12,11 @@ Supported chips:
     Addresses scanned: I2C 0x18 and 0x4e
     Datasheet: Publicly available at the National Semiconductor website
                http://www.national.com/pf/LM/LM64.html
+  * National Semiconductor LM96163
+    Prefix: 'lm96163'
+    Addresses scanned: I2C 0x4c
+    Datasheet: Publicly available at the National Semiconductor website
+               http://www.national.com/pf/LM/LM96163.html
 
 Author: Jean Delvare <khali@linux-fr.org>
 
@@ -49,16 +54,24 @@ value for measuring the speed of the fan. It can measure fan speeds down to
 Note that the pin used for fan monitoring is shared with an alert out
 function. Depending on how the board designer wanted to use the chip, fan
 speed monitoring will or will not be possible. The proper chip configuration
-is left to the BIOS, and the driver will blindly trust it.
+is left to the BIOS, and the driver will blindly trust it. Only the original
+LM63 suffers from this limitation, the LM64 and LM96163 have separate pins
+for fan monitoring and alert out. On the LM64, monitoring is always enabled;
+on the LM96163 it can be disabled.
 
 A PWM output can be used to control the speed of the fan. The LM63 has two
 PWM modes: manual and automatic. Automatic mode is not fully implemented yet
 (you cannot define your custom PWM/temperature curve), and mode change isn't
 supported either.
 
-The lm63 driver will not update its values more frequently than every
-second; reading them more often will do no harm, but will return 'old'
-values.
+The lm63 driver will not update its values more frequently than configured with
+the update_interval sysfs attribute; reading them more often will do no harm,
+but will return 'old' values. Values in the automatic fan control lookup table
+(attributes pwm1_auto_*) have their own independent lifetime of 5 seconds.
 
 The LM64 is effectively an LM63 with GPIO lines. The driver does not
 support these GPIO lines at present.
+
+The LM96163 is an enhanced version of LM63 with improved temperature accuracy
+and better PWM resolution. For LM96163, the external temperature sensor type is
+configurable as CPU embedded diode(1) or 3904 transistor(2).
diff --git a/Documentation/hwmon/pmbus b/Documentation/hwmon/pmbus
index 15ac911ce51b..d28b591753d1 100644
--- a/Documentation/hwmon/pmbus
+++ b/Documentation/hwmon/pmbus
@@ -2,9 +2,8 @@ Kernel driver pmbus
 ====================
 
 Supported chips:
-  * Ericsson BMR45X series
-    DC/DC Converter
-    Prefixes: 'bmr450', 'bmr451', 'bmr453', 'bmr454'
+  * Ericsson BMR453, BMR454
+    Prefixes: 'bmr453', 'bmr454'
     Addresses scanned: -
     Datasheet:
  http://archive.ericsson.net/service/internet/picov/get?DocNo=28701-EN/LZT146395
diff --git a/Documentation/hwmon/sysfs-interface b/Documentation/hwmon/sysfs-interface
index a4aa8f600e09..1f4dd855a299 100644
--- a/Documentation/hwmon/sysfs-interface
+++ b/Documentation/hwmon/sysfs-interface
@@ -304,7 +304,7 @@ value (fastest fan speed) wins.
 temp[1-*]_type	Sensor type selection.
 		Integers 1 to 6
 		RW
-		1: PII/Celeron Diode
+		1: CPU embedded diode
 		2: 3904 transistor
 		3: thermal diode
 		4: thermistor
diff --git a/Documentation/hwmon/w83627ehf b/Documentation/hwmon/w83627ehf
index 3f44dbdfda70..ceaf6f652b00 100644
--- a/Documentation/hwmon/w83627ehf
+++ b/Documentation/hwmon/w83627ehf
@@ -50,7 +50,7 @@ W83627DHG, W83627DHG-P, W83627UHG, W83667HG, W83667HG-B, W83667HG-I
 (NCT6775F), and NCT6776F super I/O chips. We will refer to them collectively
 as Winbond chips.
 
-The chips implement 2 to 4 temperature sensors (9 for NCT6775F and NCT6776F),
+The chips implement 3 to 4 temperature sensors (9 for NCT6775F and NCT6776F),
 2 to 5 fan rotation speed sensors, 8 to 10 analog voltage sensors, one VID
 (except for 627UHG), alarms with beep warnings (control unimplemented),
 and some automatic fan regulation strategies (plus manual fan control mode).
@@ -143,8 +143,13 @@ pwm[1-4]_min_output - minimum fan speed (range 1 - 255), when the temperature
 pwm[1-4]_stop_time  - how many milliseconds [ms] must elapse to switch
                       corresponding fan off. (when the temperature was below
                       defined range).
+pwm[1-4]_start_output-minimum fan speed (range 1 - 255) when spinning up
+pwm[1-4]_step_output- rate of fan speed change (1 - 255)
+pwm[1-4]_stop_output- minimum fan speed (range 1 - 255) when spinning down
+pwm[1-4]_max_output - maximum fan speed (range 1 - 255), when the temperature
+                      is above defined range.
 
-Note: last two functions are influenced by other control bits, not yet exported
+Note: last six functions are influenced by other control bits, not yet exported
       by the driver, so a change might not have any effect.
 
 Implementation Details
diff --git a/Documentation/hwmon/zl6100 b/Documentation/hwmon/zl6100
index 7617798b5c97..a4e8d90f59f6 100644
--- a/Documentation/hwmon/zl6100
+++ b/Documentation/hwmon/zl6100
@@ -6,6 +6,10 @@ Supported chips:
     Prefix: 'zl2004'
     Addresses scanned: -
     Datasheet: http://www.intersil.com/data/fn/fn6847.pdf
+  * Intersil / Zilker Labs ZL2005
+    Prefix: 'zl2005'
+    Addresses scanned: -
+    Datasheet: http://www.intersil.com/data/fn/fn6848.pdf
   * Intersil / Zilker Labs ZL2006
     Prefix: 'zl2006'
     Addresses scanned: -
@@ -30,6 +34,17 @@ Supported chips:
     Prefix: 'zl6105'
     Addresses scanned: -
     Datasheet: http://www.intersil.com/data/fn/fn6906.pdf
+  * Ericsson BMR450, BMR451
+    Prefix: 'bmr450', 'bmr451'
+    Addresses scanned: -
+    Datasheet:
+http://archive.ericsson.net/service/internet/picov/get?DocNo=28701-EN/LZT146401
+  * Ericsson BMR462, BMR463, BMR464
+    Prefixes: 'bmr462', 'bmr463', 'bmr464'
+    Addresses scanned: -
+    Datasheet:
+http://archive.ericsson.net/service/internet/picov/get?DocNo=28701-EN/LZT146256
+
 
 Author: Guenter Roeck <guenter.roeck@ericsson.com>
 
@@ -73,14 +88,12 @@ Module parameters
 delay
 -----
 
-Some Intersil/Zilker Labs DC-DC controllers require a minimum interval between
-I2C bus accesses. According to Intersil, the minimum interval is 2 ms, though
-1 ms appears to be sufficient and has not caused any problems in testing.
-The problem is known to affect ZL6100, ZL2105, and ZL2008. It is known not to
-affect ZL2004 and ZL6105. The driver automatically sets the interval to 1 ms
-except for ZL2004 and ZL6105. To enable manual override, the driver provides a
-writeable module parameter, 'delay', which can be used to set the interval to
-a value between 0 and 65,535 microseconds.
+Intersil/Zilker Labs DC-DC controllers require a minimum interval between I2C
+bus accesses. According to Intersil, the minimum interval is 2 ms, though 1 ms
+appears to be sufficient and has not caused any problems in testing. The problem
+is known to affect all currently supported chips. For manual override, the
+driver provides a writeable module parameter, 'delay', which can be used to set
+the interval to a value between 0 and 65,535 microseconds.
 
 
 Sysfs entries