docs: power: convert docs to ReST and rename to *.rst

Convert the PM documents to ReST, in order to allow them to
build with Sphinx.

The conversion is actually:
  - add blank lines and indentation in order to identify paragraphs;
  - fix tables markups;
  - add some lists markups;
  - mark literal blocks;
  - adjust title markups.

At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.

Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Srivatsa S. Bhat (VMware) <srivatsa@csail.mit.edu>

1 files changed, 63 insertions, 0 deletions

diff --git a/Documentation/power/swsusp-and-swap-files.rst b/Documentation/power/swsusp-and-swap-files.rst
new file mode 100644
index 000000000000..a33a2919dbe4
--- /dev/null
+++ b/Documentation/power/swsusp-and-swap-files.rst
@@ -0,0 +1,63 @@
+===============================================
+Using swap files with software suspend (swsusp)
+===============================================
+
+	(C) 2006 Rafael J. Wysocki <rjw@sisk.pl>
+
+The Linux kernel handles swap files almost in the same way as it handles swap
+partitions and there are only two differences between these two types of swap
+areas:
+(1) swap files need not be contiguous,
+(2) the header of a swap file is not in the first block of the partition that
+holds it.  From the swsusp's point of view (1) is not a problem, because it is
+already taken care of by the swap-handling code, but (2) has to be taken into
+consideration.
+
+In principle the location of a swap file's header may be determined with the
+help of appropriate filesystem driver.  Unfortunately, however, it requires the
+filesystem holding the swap file to be mounted, and if this filesystem is
+journaled, it cannot be mounted during resume from disk.  For this reason to
+identify a swap file swsusp uses the name of the partition that holds the file
+and the offset from the beginning of the partition at which the swap file's
+header is located.  For convenience, this offset is expressed in <PAGE_SIZE>
+units.
+
+In order to use a swap file with swsusp, you need to:
+
+1) Create the swap file and make it active, eg.::
+
+    # dd if=/dev/zero of=<swap_file_path> bs=1024 count=<swap_file_size_in_k>
+    # mkswap <swap_file_path>
+    # swapon <swap_file_path>
+
+2) Use an application that will bmap the swap file with the help of the
+FIBMAP ioctl and determine the location of the file's swap header, as the
+offset, in <PAGE_SIZE> units, from the beginning of the partition which
+holds the swap file.
+
+3) Add the following parameters to the kernel command line::
+
+    resume=<swap_file_partition> resume_offset=<swap_file_offset>
+
+where <swap_file_partition> is the partition on which the swap file is located
+and <swap_file_offset> is the offset of the swap header determined by the
+application in 2) (of course, this step may be carried out automatically
+by the same application that determines the swap file's header offset using the
+FIBMAP ioctl)
+
+OR
+
+Use a userland suspend application that will set the partition and offset
+with the help of the SNAPSHOT_SET_SWAP_AREA ioctl described in
+Documentation/power/userland-swsusp.rst (this is the only method to suspend
+to a swap file allowing the resume to be initiated from an initrd or initramfs
+image).
+
+Now, swsusp will use the swap file in the same way in which it would use a swap
+partition.  In particular, the swap file has to be active (ie. be present in
+/proc/swaps) so that it can be used for suspending.
+
+Note that if the swap file used for suspending is deleted and recreated,
+the location of its header need not be the same as before.  Thus every time
+this happens the value of the "resume_offset=" kernel command line parameter
+has to be updated.