MLK-15001-10 gpu: Add dpu base driver

DPU is the display processing unit embedded in i.MX8qm and i.MX8qxp.
It was originally designed by Fujitsu.
The first revision has capture controller, display controller and blit engine.
The second revision is a lite one and has display controller and blit engine.
This patch adds a base driver for DPU, which provides a thin register wrapper,
interrurpt support and client platform device register for the upper layer to
use.  Currently, the driver only supports the display controller at the pixel
processing level and only the fetchdecodes are supported/tested as the fetch
units.

Signed-off-by: Liu Ying <victor.liu@nxp.com>

1 files changed, 70 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/display/imx/fsl-imx-drm.txt b/Documentation/devicetree/bindings/display/imx/fsl-imx-drm.txt
index f79854783c2c..9fccfd4b40a8 100644
--- a/Documentation/devicetree/bindings/display/imx/fsl-imx-drm.txt
+++ b/Documentation/devicetree/bindings/display/imx/fsl-imx-drm.txt
@@ -108,6 +108,76 @@ prg@21cc000 {
 		 <&clks IMX6QDL_CLK_PRG0_AXI>;
 	clock-names = "ipg", "axi";
 	fsl,pres = <&pre1>, <&pre2>, <&pre3>;
+
+Freescale i.MX DPU
+====================
+
+Required properties:
+- compatible: Should be "fsl,<chip>-dpu"
+- reg: should be register base and length as documented in the
+  datasheet
+- intsteer: phandle pointing to interrupt steer.
+- interrupts, interrupt-names: Should contain interrupts and names as
+  documented in the datasheet.
+- clocks, clock-names: phandles to the DPU clocks described in
+  Documentation/devicetree/bindings/clock/clock-bindings.txt
+  The following clocks are expected on i.MX8qm and i.MX8qxp:
+           "pll0" - PLL clock for display interface 0
+           "pll1" - PLL clock for display interface 1
+           "disp0" - pixel clock for display interface 0
+           "disp1" - pixel clock for display interface 1
+  The needed clock numbers for each are documented in
+  Documentation/devicetree/bindings/clock/imx8qm-clock.txt, and in
+  Documentation/devicetree/bindings/clock/imx8qxp-clock.txt.
+- power-domains: phandle pointing to power domain.
+Optional properties:
+- port@[0-1]: Port nodes with endpoint definitions as defined in
+  Documentation/devicetree/bindings/media/video-interfaces.txt.
+  ports 0 and 1 should correspond to display interface 0 and
+  display interface 1, respectively.
+
+example:
+
+dpu: dpu@56180000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "fsl,imx8qm-dpu";
+	reg = <0x0 0x56180000 0x0 0x40000>;
+	intsteer = <&dpu1_intsteer>;
+	interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+	interrupt-names = "irq_common",
+			  "irq_stream0a",
+			  "irq_stream0b",
+			  "irq_stream1a",
+			  "irq_stream1b",
+			  "irq_reserved0",
+			  "irq_reserved1",
+			  "irq_blit";
+	clocks = <&clk IMX8QM_DC0_PLL0_CLK>,
+		 <&clk IMX8QM_DC0_PLL1_CLK>,
+		 <&clk IMX8QM_DC0_DISP0_CLK>,
+		 <&clk IMX8QM_DC0_DISP1_CLK>;
+	clock-names = "pll0", "pll1", "disp0", "disp1";
+	power-domains = <&pd_dc0>;
+
+	dpu1_disp1: port@1 {
+		reg = <1>;
+
+		dpu1_disp1_lvds0: lvds0-endpoint {
+			remote-endpoint = <&ldb1_lvds0>;
+		};
+
+		dpu1_disp1_lvds1: lvds1-endpoint {
+			remote-endpoint = <&ldb1_lvds1>;
+		};
+	};
 };
 
 Parallel display support