Merge tag 'spi-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi

Pull spi updates from Mark Brown:
 "The main focus of this release from a framework point of view has been
  spi-mem where we've acquired support for a few new hardware features
  which enable better performance on suitable hardware.

  Otherwise mostly thanks to Arnd's cleanup efforts on old platforms
  we've removed several obsolete drivers which just about balance out
  the newer drivers we've added this cycle.

  Summary:

   - Allow drivers to flag if they are unidirectional.

   - Support for DTR mode and hardware acceleration of dummy cycles in
     spi-mem.

   - Support for Allwinder H616, Intel Lightning Mountain, nVidia Tegra
     QuadSPI, Realtek RTL838x and RTL839x.

   - Removal of obsolete EFM32, Txx9 and SIRF Prima and Atlas drivers"

* tag 'spi-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (76 commits)
  spi: Skip zero-length transfers in spi_transfer_one_message()
  spi: dw: Avoid stack content exposure
  spi: cadence-quadspi: Use spi_mem_dtr_supports_op()
  spi: spi-mem: add spi_mem_dtr_supports_op()
  spi: atmel-quadspi: Disable the QSPI IP at suspend()
  spi: pxa2xx: Add IDs for the controllers found on Intel Lynxpoint
  spi: pxa2xx: Fix the controller numbering for Wildcat Point
  spi: Change provied to provided in the file spi.h
  spi: mediatek: add set_cs_timing support
  spi: support CS timing for HW & SW mode
  spi: add power control when set_cs_timing
  spi: stm32: make spurious and overrun interrupts visible
  spi: stm32h7: replace private SPI_1HZ_NS with NSEC_PER_SEC
  spi: stm32: defer probe for reset
  spi: stm32: driver uses reset controller only at init
  spi: stm32h7: ensure message are smaller than max size
  spi: stm32: use bitfield macros
  spi: stm32: do not mandate cs_gpio
  spi: stm32: properly handle 0 byte transfer
  spi: clps711xx: remove redundant white-space
  ...

7 files changed, 165 insertions, 44 deletions

diff --git a/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml b/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml
index 7866a655d81c..908248260afa 100644
--- a/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml
+++ b/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml
@@ -25,6 +25,7 @@ properties:
           - enum:
               - allwinner,sun8i-r40-spi
               - allwinner,sun50i-h6-spi
+              - allwinner,sun50i-h616-spi
           - const: allwinner,sun8i-h3-spi
 
   reg:
diff --git a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt b/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
index 945be7d5b236..8ace832a2d80 100644
--- a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt
+++ b/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
@@ -5,6 +5,7 @@ Required properties:
 	Generic default - "cdns,qspi-nor".
 	For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor".
 	For TI AM654 SoC  - "ti,am654-ospi", "cdns,qspi-nor".
+	For Intel LGM SoC - "intel,lgm-qspi", "cdns,qspi-nor".
 - reg : Contains two entries, each of which is a tuple consisting of a
 	physical address and length. The first entry is the address and
 	length of the controller register set. The second entry is the
diff --git a/Documentation/devicetree/bindings/spi/nvidia,tegra210-quad.yaml b/Documentation/devicetree/bindings/spi/nvidia,tegra210-quad.yaml
new file mode 100644
index 000000000000..35a8045b2c70
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/nvidia,tegra210-quad.yaml
@@ -0,0 +1,117 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/nvidia,tegra210-quad.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Tegra Quad SPI Controller
+
+maintainers:
+  - Thierry Reding <thierry.reding@gmail.com>
+  - Jonathan Hunter <jonathanh@nvidia.com>
+
+allOf:
+  - $ref: "spi-controller.yaml#"
+
+properties:
+  compatible:
+    enum:
+      - nvidia,tegra210-qspi
+      - nvidia,tegra186-qspi
+      - nvidia,tegra194-qspi
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clock-names:
+    items:
+      - const: qspi
+      - const: qspi_out
+
+  clocks:
+    maxItems: 2
+
+  resets:
+    maxItems: 1
+
+  dmas:
+    maxItems: 2
+
+  dma-names:
+    items:
+      - const: rx
+      - const: tx
+
+patternProperties:
+  "@[0-9a-f]+":
+    type: object
+
+    properties:
+      spi-rx-bus-width:
+        enum: [1, 2, 4]
+
+      spi-tx-bus-width:
+        enum: [1, 2, 4]
+
+      nvidia,tx-clk-tap-delay:
+        description:
+          Delays the clock going out to device with this tap value.
+          Tap value varies based on platform design trace lengths from Tegra
+          QSPI to corresponding slave device.
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 31
+
+      nvidia,rx-clk-tap-delay:
+        description:
+          Delays the clock coming in from the device with this tap value.
+          Tap value varies based on platform design trace lengths from Tegra
+          QSPI to corresponding slave device.
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 255
+
+    required:
+      - reg
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clock-names
+  - clocks
+  - resets
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/tegra210-car.h>
+    #include <dt-bindings/reset/tegra210-car.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    spi@70410000 {
+            compatible = "nvidia,tegra210-qspi";
+            reg = <0x70410000 0x1000>;
+            interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+            #address-cells = <1>;
+            #size-cells = <0>;
+            clocks = <&tegra_car TEGRA210_CLK_QSPI>,
+                     <&tegra_car TEGRA210_CLK_QSPI_PM>;
+            clock-names = "qspi", "qspi_out";
+            resets = <&tegra_car 211>;
+            dmas = <&apbdma 5>, <&apbdma 5>;
+            dma-names = "rx", "tx";
+
+            flash@0 {
+                    compatible = "spi-nor";
+                    reg = <0>;
+                    spi-max-frequency = <104000000>;
+                    spi-tx-bus-width = <2>;
+                    spi-rx-bus-width = <2>;
+                    nvidia,tx-clk-tap-delay = <0>;
+                    nvidia,rx-clk-tap-delay = <0>;
+            };
+    };
diff --git a/Documentation/devicetree/bindings/spi/realtek,rtl-spi.yaml b/Documentation/devicetree/bindings/spi/realtek,rtl-spi.yaml
new file mode 100644
index 000000000000..30a62a211984
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/realtek,rtl-spi.yaml
@@ -0,0 +1,41 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/realtek,rtl-spi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Realtek RTL838x/RTL839x SPI controller
+
+maintainers:
+  - Bert Vermeulen <bert@biot.com>
+  - Birger Koblitz <mail@birger-koblitz.de>
+
+allOf:
+  - $ref: "spi-controller.yaml#"
+
+properties:
+  compatible:
+    oneOf:
+      - const: realtek,rtl8380-spi
+      - const: realtek,rtl8382-spi
+      - const: realtek,rtl8391-spi
+      - const: realtek,rtl8392-spi
+      - const: realtek,rtl8393-spi
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    spi: spi@1200 {
+        compatible = "realtek,rtl8382-spi";
+        reg = <0x1200 0x100>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+    };
diff --git a/Documentation/devicetree/bindings/spi/renesas,sh-msiof.yaml b/Documentation/devicetree/bindings/spi/renesas,sh-msiof.yaml
index 44c7ddb4b109..b104899205f6 100644
--- a/Documentation/devicetree/bindings/spi/renesas,sh-msiof.yaml
+++ b/Documentation/devicetree/bindings/spi/renesas,sh-msiof.yaml
@@ -47,6 +47,7 @@ properties:
               - renesas,msiof-r8a77980      # R-Car V3H
               - renesas,msiof-r8a77990      # R-Car E3
               - renesas,msiof-r8a77995      # R-Car D3
+              - renesas,msiof-r8a779a0      # R-Car V3U
           - const: renesas,rcar-gen3-msiof  # generic R-Car Gen3 and RZ/G2
                                             # compatible device
       - items:
diff --git a/Documentation/devicetree/bindings/spi/spi-controller.yaml b/Documentation/devicetree/bindings/spi/spi-controller.yaml
index 5f505810104d..06786f1b43d2 100644
--- a/Documentation/devicetree/bindings/spi/spi-controller.yaml
+++ b/Documentation/devicetree/bindings/spi/spi-controller.yaml
@@ -152,8 +152,9 @@ patternProperties:
       spi-rx-bus-width:
         description:
           Bus width to the SPI bus used for read transfers.
+          If 0 is provided, then no RX will be possible on this device.
         $ref: /schemas/types.yaml#/definitions/uint32
-        enum: [1, 2, 4, 8]
+        enum: [0, 1, 2, 4, 8]
         default: 1
 
       spi-rx-delay-us:
@@ -163,8 +164,9 @@ patternProperties:
       spi-tx-bus-width:
         description:
           Bus width to the SPI bus used for write transfers.
+          If 0 is provided, then no TX will be possible on this device.
         $ref: /schemas/types.yaml#/definitions/uint32
-        enum: [1, 2, 4, 8]
+        enum: [0, 1, 2, 4, 8]
         default: 1
 
       spi-tx-delay-us:
diff --git a/Documentation/devicetree/bindings/spi/spi-sirf.txt b/Documentation/devicetree/bindings/spi/spi-sirf.txt
deleted file mode 100644
index ddd78ff68fae..000000000000
--- a/Documentation/devicetree/bindings/spi/spi-sirf.txt
+++ /dev/null
@@ -1,42 +0,0 @@
-* CSR SiRFprimaII Serial Peripheral Interface
-
-Required properties:
-- compatible : Should be "sirf,prima2-spi", "sirf,prima2-usp"
-               or "sirf,atlas7-usp"
-- reg : Offset and length of the register set for the device
-- interrupts : Should contain SPI interrupt
-- resets: phandle to the reset controller asserting this device in
-          reset
-  See ../reset/reset.txt for details.
-- dmas : Must contain an entry for each entry in clock-names.
-  See ../dma/dma.txt for details.
-- dma-names : Must include the following entries:
-  - rx
-  - tx
-- clocks : Must contain an entry for each entry in clock-names.
-  See ../clocks/clock-bindings.txt for details.
-
-- #address-cells: Number of cells required to define a chip select
-                  address on the SPI bus. Should be set to 1.
-- #size-cells:    Should be zero.
-
-Optional properties:
-- spi-max-frequency: Specifies maximum SPI clock frequency,
-                     Units - Hz. Definition as per
-                     Documentation/devicetree/bindings/spi/spi-bus.txt
-- cs-gpios:     should specify GPIOs used for chipselects.
-
-Example:
-
-spi0: spi@b00d0000 {
-	compatible = "sirf,prima2-spi";
-	reg = <0xb00d0000 0x10000>;
-	interrupts = <15>;
-	dmas = <&dmac1 9>,
-		<&dmac1 4>;
-	dma-names = "rx", "tx";
-	#address-cells = <1>;
-	#size-cells = <0>;
-	clocks = <&clks 19>;
-	resets = <&rstc 26>;
-};