Merge commit 'v2.6.29-rc4' into core/percpu

Conflicts:
	arch/x86/mach-voyager/voyager_smp.c
	arch/x86/mm/fault.c

7 files changed, 272 insertions, 309 deletions

diff --git a/Documentation/block/queue-sysfs.txt b/Documentation/block/queue-sysfs.txt
new file mode 100644
index 000000000000..e164403f60e1
--- /dev/null
+++ b/Documentation/block/queue-sysfs.txt
@@ -0,0 +1,63 @@
+Queue sysfs files
+=================
+
+This text file will detail the queue files that are located in the sysfs tree
+for each block device. Note that stacked devices typically do not export
+any settings, since their queue merely functions are a remapping target.
+These files are the ones found in the /sys/block/xxx/queue/ directory.
+
+Files denoted with a RO postfix are readonly and the RW postfix means
+read-write.
+
+hw_sector_size (RO)
+-------------------
+This is the hardware sector size of the device, in bytes.
+
+max_hw_sectors_kb (RO)
+----------------------
+This is the maximum number of kilobytes supported in a single data transfer.
+
+max_sectors_kb (RW)
+-------------------
+This is the maximum number of kilobytes that the block layer will allow
+for a filesystem request. Must be smaller than or equal to the maximum
+size allowed by the hardware.
+
+nomerges (RW)
+-------------
+This enables the user to disable the lookup logic involved with IO merging
+requests in the block layer. Merging may still occur through a direct
+1-hit cache, since that comes for (almost) free. The IO scheduler will not
+waste cycles doing tree/hash lookups for merges if nomerges is 1. Defaults
+to 0, enabling all merges.
+
+nr_requests (RW)
+----------------
+This controls how many requests may be allocated in the block layer for
+read or write requests. Note that the total allocated number may be twice
+this amount, since it applies only to reads or writes (not the accumulated
+sum).
+
+read_ahead_kb (RW)
+------------------
+Maximum number of kilobytes to read-ahead for filesystems on this block
+device.
+
+rq_affinity (RW)
+----------------
+If this option is enabled, the block layer will migrate request completions
+to the CPU that originally submitted the request. For some workloads
+this provides a significant reduction in CPU cycles due to caching effects.
+
+scheduler (RW)
+--------------
+When read, this file will display the current and available IO schedulers
+for this block device. The currently active IO scheduler will be enclosed
+in [] brackets. Writing an IO scheduler name to this file will switch
+control of this block device to that new IO scheduler. Note that writing
+an IO scheduler name to this file will attempt to load that IO scheduler
+module, if it isn't already present in the system.
+
+
+
+Jens Axboe <jens.axboe@oracle.com>, February 2009
diff --git a/Documentation/cpu-freq/user-guide.txt b/Documentation/cpu-freq/user-guide.txt
index e3443ddcfb89..917918f84fc7 100644
--- a/Documentation/cpu-freq/user-guide.txt
+++ b/Documentation/cpu-freq/user-guide.txt
@@ -195,19 +195,3 @@ scaling_setspeed.		By "echoing" a new frequency into this
 				you can change the speed of the CPU,
 				but only within the limits of
 				scaling_min_freq and scaling_max_freq.
-				
-
-3.2 Deprecated Interfaces
--------------------------
-
-Depending on your kernel configuration, you might find the following 
-cpufreq-related files:
-/proc/cpufreq
-/proc/sys/cpu/*/speed
-/proc/sys/cpu/*/speed-min
-/proc/sys/cpu/*/speed-max
-
-These are files for deprecated interfaces to cpufreq, which offer far
-less functionality. Because of this, these interfaces aren't described
-here.
-
diff --git a/Documentation/filesystems/sysfs-pci.txt b/Documentation/filesystems/sysfs-pci.txt
index 68ef48839c04..9f8740ca3f3b 100644
--- a/Documentation/filesystems/sysfs-pci.txt
+++ b/Documentation/filesystems/sysfs-pci.txt
@@ -9,6 +9,7 @@ that support it.  For example, a given bus might look like this:
      |   |-- class
      |   |-- config
      |   |-- device
+     |   |-- enable
      |   |-- irq
      |   |-- local_cpus
      |   |-- resource
@@ -32,6 +33,7 @@ files, each with their own function.
        class		   PCI class (ascii, ro)
        config		   PCI config space (binary, rw)
        device		   PCI device (ascii, ro)
+       enable	           Whether the device is enabled (ascii, rw)
        irq		   IRQ number (ascii, ro)
        local_cpus	   nearby CPU mask (cpumask, ro)
        resource		   PCI resource host addresses (ascii, ro)
@@ -57,10 +59,19 @@ used to do actual device programming from userspace.  Note that some platforms
 don't support mmapping of certain resources, so be sure to check the return
 value from any attempted mmap.
 
+The 'enable' file provides a counter that indicates how many times the device 
+has been enabled.  If the 'enable' file currently returns '4', and a '1' is
+echoed into it, it will then return '5'.  Echoing a '0' into it will decrease
+the count.  Even when it returns to 0, though, some of the initialisation
+may not be reversed.  
+
 The 'rom' file is special in that it provides read-only access to the device's
 ROM file, if available.  It's disabled by default, however, so applications
 should write the string "1" to the file to enable it before attempting a read
-call, and disable it following the access by writing "0" to the file.
+call, and disable it following the access by writing "0" to the file.  Note
+that the device must be enabled for a rom read to return data succesfully.
+In the event a driver is not bound to the device, it can be enabled using the
+'enable' file, documented above.
 
 Accessing legacy resources through sysfs
 ----------------------------------------
diff --git a/Documentation/filesystems/ubifs.txt b/Documentation/filesystems/ubifs.txt
index 84da2a4ba25a..12fedb7834c6 100644
--- a/Documentation/filesystems/ubifs.txt
+++ b/Documentation/filesystems/ubifs.txt
@@ -79,13 +79,6 @@ Mount options
 
 (*) == default.
 
-norm_unmount (*)	commit on unmount; the journal is committed
-			when the file-system is unmounted so that the
-			next mount does not have to replay the journal
-			and it becomes very fast;
-fast_unmount		do not commit on unmount; this option makes
-			unmount faster, but the next mount slower
-			because of the need to replay the journal.
 bulk_read		read more in one go to take advantage of flash
 			media that read faster sequentially
 no_bulk_read (*)	do not bulk-read
diff --git a/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt b/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt
new file mode 100644
index 000000000000..8447fd7090d0
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt
@@ -0,0 +1,180 @@
+MPC5200 Device Tree Bindings
+----------------------------
+
+(c) 2006-2009 Secret Lab Technologies Ltd
+Grant Likely <grant.likely@secretlab.ca>
+
+Naming conventions
+------------------
+For mpc5200 on-chip devices, the format for each compatible value is
+<chip>-<device>[-<mode>].  The OS should be able to match a device driver
+to the device based solely on the compatible value.  If two drivers
+match on the compatible list; the 'most compatible' driver should be
+selected.
+
+The split between the MPC5200 and the MPC5200B leaves a bit of a
+conundrum.  How should the compatible property be set up to provide
+maximum compatibility information; but still accurately describe the
+chip?  For the MPC5200; the answer is easy.  Most of the SoC devices
+originally appeared on the MPC5200.  Since they didn't exist anywhere
+else; the 5200 compatible properties will contain only one item;
+"fsl,mpc5200-<device>".
+
+The 5200B is almost the same as the 5200, but not quite.  It fixes
+silicon bugs and it adds a small number of enhancements.  Most of the
+devices either provide exactly the same interface as on the 5200.  A few
+devices have extra functions but still have a backwards compatible mode.
+To express this information as completely as possible, 5200B device trees
+should have two items in the compatible list:
+	compatible = "fsl,mpc5200b-<device>","fsl,mpc5200-<device>";
+
+It is *strongly* recommended that 5200B device trees follow this convention
+(instead of only listing the base mpc5200 item).
+
+ie. ethernet on mpc5200: compatible = "fsl,mpc5200-fec";
+    ethernet on mpc5200b: compatible = "fsl,mpc5200b-fec", "fsl,mpc5200-fec";
+
+Modal devices, like PSCs, also append the configured function to the
+end of the compatible field.  ie. A PSC in i2s mode would specify
+"fsl,mpc5200-psc-i2s", not "fsl,mpc5200-i2s".  This convention is chosen to
+avoid naming conflicts with non-psc devices providing the same
+function.  For example, "fsl,mpc5200-spi" and "fsl,mpc5200-psc-spi" describe
+the mpc5200 simple spi device and a PSC spi mode respectively.
+
+At the time of writing, exact chip may be either 'fsl,mpc5200' or
+'fsl,mpc5200b'.
+
+The soc node
+------------
+This node describes the on chip SOC peripherals.  Every mpc5200 based
+board will have this node, and as such there is a common naming
+convention for SOC devices.
+
+Required properties:
+name			description
+----			-----------
+ranges			Memory range of the internal memory mapped registers.
+			Should be <0 [baseaddr] 0xc000>
+reg			Should be <[baseaddr] 0x100>
+compatible		mpc5200: "fsl,mpc5200-immr"
+			mpc5200b: "fsl,mpc5200b-immr"
+system-frequency	'fsystem' frequency in Hz; XLB, IPB, USB and PCI
+			clocks are derived from the fsystem clock.
+bus-frequency		IPB bus frequency in Hz.  Clock rate
+			used by most of the soc devices.
+
+soc child nodes
+---------------
+Any on chip SOC devices available to Linux must appear as soc5200 child nodes.
+
+Note: The tables below show the value for the mpc5200.  A mpc5200b device
+tree should use the "fsl,mpc5200b-<device>","fsl,mpc5200-<device>" form.
+
+Required soc5200 child nodes:
+name				compatible		Description
+----				----------		-----------
+cdm@<addr>			fsl,mpc5200-cdm		Clock Distribution
+interrupt-controller@<addr>	fsl,mpc5200-pic		need an interrupt
+							controller to boot
+bestcomm@<addr>			fsl,mpc5200-bestcomm	Bestcomm DMA controller
+
+Recommended soc5200 child nodes; populate as needed for your board
+name		compatible		Description
+----		----------		-----------
+timer@<addr>	fsl,mpc5200-gpt		 General purpose timers
+gpio@<addr>	fsl,mpc5200-gpio	 MPC5200 simple gpio controller
+gpio@<addr>	fsl,mpc5200-gpio-wkup	 MPC5200 wakeup gpio controller
+rtc@<addr>	fsl,mpc5200-rtc		 Real time clock
+mscan@<addr>	fsl,mpc5200-mscan	 CAN bus controller
+pci@<addr>	fsl,mpc5200-pci		 PCI bridge
+serial@<addr>	fsl,mpc5200-psc-uart	 PSC in serial mode
+i2s@<addr>	fsl,mpc5200-psc-i2s	 PSC in i2s mode
+ac97@<addr>	fsl,mpc5200-psc-ac97	 PSC in ac97 mode
+spi@<addr>	fsl,mpc5200-psc-spi	 PSC in spi mode
+irda@<addr>	fsl,mpc5200-psc-irda	 PSC in IrDA mode
+spi@<addr>	fsl,mpc5200-spi		 MPC5200 spi device
+ethernet@<addr>	fsl,mpc5200-fec		 MPC5200 ethernet device
+ata@<addr>	fsl,mpc5200-ata		 IDE ATA interface
+i2c@<addr>	fsl,mpc5200-i2c		 I2C controller
+usb@<addr>	fsl,mpc5200-ohci,ohci-be USB controller
+xlb@<addr>	fsl,mpc5200-xlb		 XLB arbitrator
+
+fsl,mpc5200-gpt nodes
+---------------------
+On the mpc5200 and 5200b, GPT0 has a watchdog timer function.  If the board
+design supports the internal wdt, then the device node for GPT0 should
+include the empty property 'fsl,has-wdt'.
+
+An mpc5200-gpt can be used as a single line GPIO controller.  To do so,
+add the following properties to the gpt node:
+	gpio-controller;
+	#gpio-cells = <2>;
+When referencing the GPIO line from another node, the first cell must always
+be zero and the second cell represents the gpio flags and described in the
+gpio device tree binding.
+
+An mpc5200-gpt can be used as a single line edge sensitive interrupt
+controller.  To do so, add the following properties to the gpt node:
+	interrupt-controller;
+	#interrupt-cells = <1>;
+When referencing the IRQ line from another node, the cell represents the
+sense mode; 1 for edge rising, 2 for edge falling.
+
+fsl,mpc5200-psc nodes
+---------------------
+The PSCs should include a cell-index which is the index of the PSC in
+hardware.  cell-index is used to determine which shared SoC registers to
+use when setting up PSC clocking.  cell-index number starts at '0'.  ie:
+	PSC1 has 'cell-index = <0>'
+	PSC4 has 'cell-index = <3>'
+
+PSC in i2s mode:  The mpc5200 and mpc5200b PSCs are not compatible when in
+i2s mode.  An 'mpc5200b-psc-i2s' node cannot include 'mpc5200-psc-i2s' in the
+compatible field.
+
+
+fsl,mpc5200-gpio and fsl,mpc5200-gpio-wkup nodes
+------------------------------------------------
+Each GPIO controller node should have the empty property gpio-controller and
+#gpio-cells set to 2. First cell is the GPIO number which is interpreted
+according to the bit numbers in the GPIO control registers. The second cell
+is for flags which is currently unused.
+
+fsl,mpc5200-fec nodes
+---------------------
+The FEC node can specify one of the following properties to configure
+the MII link:
+- fsl,7-wire-mode - An empty property that specifies the link uses 7-wire
+                    mode instead of MII
+- current-speed   - Specifies that the MII should be configured for a fixed
+                    speed.  This property should contain two cells.  The
+                    first cell specifies the speed in Mbps and the second
+                    should be '0' for half duplex and '1' for full duplex
+- phy-handle      - Contains a phandle to an Ethernet PHY.
+
+Interrupt controller (fsl,mpc5200-pic) node
+-------------------------------------------
+The mpc5200 pic binding splits hardware IRQ numbers into two levels.  The
+split reflects the layout of the PIC hardware itself, which groups
+interrupts into one of three groups; CRIT, MAIN or PERP.  Also, the
+Bestcomm dma engine has it's own set of interrupt sources which are
+cascaded off of peripheral interrupt 0, which the driver interprets as a
+fourth group, SDMA.
+
+The interrupts property for device nodes using the mpc5200 pic consists
+of three cells; <L1 L2 level>
+
+    L1 := [CRIT=0, MAIN=1, PERP=2, SDMA=3]
+    L2 := interrupt number; directly mapped from the value in the
+          "ICTL PerStat, MainStat, CritStat Encoded Register"
+    level := [LEVEL_HIGH=0, EDGE_RISING=1, EDGE_FALLING=2, LEVEL_LOW=3]
+
+For external IRQs, use the following interrupt property values (how to
+specify external interrupts is a frequently asked question):
+External interrupts:
+	external irq0:	interrupts = <0 0 n>;
+	external irq1:	interrupts = <1 1 n>;
+	external irq2:	interrupts = <1 2 n>;
+	external irq3:	interrupts = <1 3 n>;
+'n' is sense (0: level high, 1: edge rising, 2: edge falling 3: level low)
+
diff --git a/Documentation/powerpc/mpc52xx-device-tree-bindings.txt b/Documentation/powerpc/mpc52xx-device-tree-bindings.txt
deleted file mode 100644
index 6f12f1c79c0c..000000000000
--- a/Documentation/powerpc/mpc52xx-device-tree-bindings.txt
+++ /dev/null
@@ -1,277 +0,0 @@
-MPC5200 Device Tree Bindings
-----------------------------
-
-(c) 2006-2007 Secret Lab Technologies Ltd
-Grant Likely <grant.likely at secretlab.ca>
-
-********** DRAFT ***********
-* WARNING: Do not depend on the stability of these bindings just yet.
-* The MPC5200 device tree conventions are still in flux
-* Keep an eye on the linuxppc-dev mailing list for more details
-********** DRAFT ***********
-
-I - Introduction
-================
-Boards supported by the arch/powerpc architecture require device tree be
-passed by the boot loader to the kernel at boot time.  The device tree
-describes what devices are present on the board and how they are
-connected.  The device tree can either be passed as a binary blob (as
-described in Documentation/powerpc/booting-without-of.txt), or passed
-by Open Firmware (IEEE 1275) compatible firmware using an OF compatible
-client interface API.
-
-This document specifies the requirements on the device-tree for mpc5200
-based boards.  These requirements are above and beyond the details
-specified in either the Open Firmware spec or booting-without-of.txt
-
-All new mpc5200-based boards are expected to match this document.  In
-cases where this document is not sufficient to support a new board port,
-this document should be updated as part of adding the new board support.
-
-II - Philosophy
-===============
-The core of this document is naming convention.  The whole point of
-defining this convention is to reduce or eliminate the number of
-special cases required to support a 5200 board.  If all 5200 boards
-follow the same convention, then generic 5200 support code will work
-rather than coding special cases for each new board.
-
-This section tries to capture the thought process behind why the naming
-convention is what it is.
-
-1.  names
----------
-There is strong convention/requirements already established for children
-of the root node.  'cpus' describes the processor cores, 'memory'
-describes memory, and 'chosen' provides boot configuration.  Other nodes
-are added to describe devices attached to the processor local bus.
-
-Following convention already established with other system-on-chip
-processors, 5200 device trees should use the name 'soc5200' for the
-parent node of on chip devices, and the root node should be its parent.
-
-Child nodes are typically named after the configured function.  ie.
-the FEC node is named 'ethernet', and a PSC in uart mode is named 'serial'.
-
-2. device_type property
------------------------
-similar to the node name convention above; the device_type reflects the
-configured function of a device.  ie. 'serial' for a uart and 'spi' for
-an spi controller.  However, while node names *should* reflect the
-configured function, device_type *must* match the configured function
-exactly.
-
-3. compatible property
-----------------------
-Since device_type isn't enough to match devices to drivers, there also
-needs to be a naming convention for the compatible property.  Compatible
-is an list of device descriptions sorted from specific to generic.  For
-the mpc5200, the required format for each compatible value is
-<chip>-<device>[-<mode>].  The OS should be able to match a device driver
-to the device based solely on the compatible value.  If two drivers
-match on the compatible list; the 'most compatible' driver should be
-selected.
-
-The split between the MPC5200 and the MPC5200B leaves a bit of a
-conundrum.  How should the compatible property be set up to provide
-maximum compatibility information; but still accurately describe the
-chip?  For the MPC5200; the answer is easy.  Most of the SoC devices
-originally appeared on the MPC5200.  Since they didn't exist anywhere
-else; the 5200 compatible properties will contain only one item;
-"mpc5200-<device>".
-
-The 5200B is almost the same as the 5200, but not quite.  It fixes
-silicon bugs and it adds a small number of enhancements.  Most of the
-devices either provide exactly the same interface as on the 5200.  A few
-devices have extra functions but still have a backwards compatible mode.
-To express this information as completely as possible, 5200B device trees
-should have two items in the compatible list;
-"mpc5200b-<device>\0mpc5200-<device>".  It is *strongly* recommended
-that 5200B device trees follow this convention (instead of only listing
-the base mpc5200 item).
-
-If another chip appear on the market with one of the mpc5200 SoC
-devices, then the compatible list should include mpc5200-<device>.
-
-ie. ethernet on mpc5200: compatible = "mpc5200-ethernet"
-    ethernet on mpc5200b: compatible = "mpc5200b-ethernet\0mpc5200-ethernet"
-
-Modal devices, like PSCs, also append the configured function to the
-end of the compatible field.  ie. A PSC in i2s mode would specify
-"mpc5200-psc-i2s", not "mpc5200-i2s".  This convention is chosen to
-avoid naming conflicts with non-psc devices providing the same
-function.  For example, "mpc5200-spi" and "mpc5200-psc-spi" describe
-the mpc5200 simple spi device and a PSC spi mode respectively.
-
-If the soc device is more generic and present on other SOCs, the
-compatible property can specify the more generic device type also.
-
-ie. mscan: compatible = "mpc5200-mscan\0fsl,mscan";
-
-At the time of writing, exact chip may be either 'mpc5200' or
-'mpc5200b'.
-
-Device drivers should always try to match as generically as possible.
-
-III - Structure
-===============
-The device tree for an mpc5200 board follows the structure defined in
-booting-without-of.txt with the following additional notes:
-
-0) the root node
-----------------
-Typical root description node; see booting-without-of
-
-1) The cpus node
-----------------
-The cpus node follows the basic layout described in booting-without-of.
-The bus-frequency property holds the XLB bus frequency
-The clock-frequency property holds the core frequency
-
-2) The memory node
-------------------
-Typical memory description node; see booting-without-of.
-
-3) The soc5200 node
--------------------
-This node describes the on chip SOC peripherals.  Every mpc5200 based
-board will have this node, and as such there is a common naming
-convention for SOC devices.
-
-Required properties:
-name			type		description
-----			----		-----------
-device_type		string		must be "soc"
-ranges			int		should be <0 baseaddr baseaddr+10000>
-reg			int		must be <baseaddr 10000>
-compatible		string		mpc5200: "mpc5200-soc"
-					mpc5200b: "mpc5200b-soc\0mpc5200-soc"
-system-frequency	int		Fsystem frequency; source of all
-					other clocks.
-bus-frequency		int		IPB bus frequency in HZ.  Clock rate
-					used by most of the soc devices.
-#interrupt-cells	int		must be <3>.
-
-Recommended properties:
-name			type		description
-----			----		-----------
-model			string		Exact model of the chip;
-					ie: model="fsl,mpc5200"
-revision		string		Silicon revision of chip
-					ie: revision="M08A"
-
-The 'model' and 'revision' properties are *strongly* recommended.  Having
-them presence acts as a bit of a safety net for working around as yet
-undiscovered bugs on one version of silicon.  For example, device drivers
-can use the model and revision properties to decide if a bug fix should
-be turned on.
-
-4) soc5200 child nodes
-----------------------
-Any on chip SOC devices available to Linux must appear as soc5200 child nodes.
-
-Note: The tables below show the value for the mpc5200.  A mpc5200b device
-tree should use the "mpc5200b-<device>\0mpc5200-<device> form.
-
-Required soc5200 child nodes:
-name		device_type		compatible	Description
-----		-----------		----------	-----------
-cdm@<addr>	cdm			mpc5200-cmd	Clock Distribution
-pic@<addr>	interrupt-controller	mpc5200-pic	need an interrupt
-							controller to boot
-bestcomm@<addr>	dma-controller		mpc5200-bestcomm 5200 pic also requires
-							 the bestcomm device
-
-Recommended soc5200 child nodes; populate as needed for your board
-name		device_type	compatible	  Description
-----		-----------	----------	  -----------
-gpt@<addr>	gpt		fsl,mpc5200-gpt	  General purpose timers
-gpt@<addr>	gpt		fsl,mpc5200-gpt-gpio	General purpose
-							timers in GPIO mode
-gpio@<addr>			fsl,mpc5200-gpio	MPC5200 simple gpio
-							controller
-gpio@<addr>			fsl,mpc5200-gpio-wkup	MPC5200 wakeup gpio
-							controller
-rtc@<addr>	rtc		mpc5200-rtc	  Real time clock
-mscan@<addr>	mscan		mpc5200-mscan	  CAN bus controller
-pci@<addr>	pci		mpc5200-pci	  PCI bridge
-serial@<addr>	serial		mpc5200-psc-uart  PSC in serial mode
-i2s@<addr>	sound		mpc5200-psc-i2s	  PSC in i2s mode
-ac97@<addr>	sound		mpc5200-psc-ac97  PSC in ac97 mode
-spi@<addr>	spi		mpc5200-psc-spi	  PSC in spi mode
-irda@<addr>	irda		mpc5200-psc-irda  PSC in IrDA mode
-spi@<addr>	spi		mpc5200-spi	  MPC5200 spi device
-ethernet@<addr>	network		mpc5200-fec	  MPC5200 ethernet device
-ata@<addr>	ata		mpc5200-ata	  IDE ATA interface
-i2c@<addr>	i2c		mpc5200-i2c	  I2C controller
-usb@<addr>	usb-ohci-be	mpc5200-ohci,ohci-be	USB controller
-xlb@<addr>	xlb		mpc5200-xlb	  XLB arbitrator
-
-Important child node properties
-name		type		description
-----		----		-----------
-cell-index	int		When multiple devices are present, is the
-				index of the device in the hardware (ie. There
-				are 6 PSC on the 5200 numbered PSC1 to PSC6)
-				    PSC1 has 'cell-index = <0>'
-				    PSC4 has 'cell-index = <3>'
-
-5) General Purpose Timer nodes (child of soc5200 node)
-On the mpc5200 and 5200b, GPT0 has a watchdog timer function.  If the board
-design supports the internal wdt, then the device node for GPT0 should
-include the empty property 'fsl,has-wdt'.
-
-6) PSC nodes (child of soc5200 node)
-PSC nodes can define the optional 'port-number' property to force assignment
-order of serial ports.  For example, PSC5 might be physically connected to
-the port labeled 'COM1' and PSC1 wired to 'COM1'.  In this case, PSC5 would
-have a "port-number = <0>" property, and PSC1 would have "port-number = <1>".
-
-PSC in i2s mode:  The mpc5200 and mpc5200b PSCs are not compatible when in
-i2s mode.  An 'mpc5200b-psc-i2s' node cannot include 'mpc5200-psc-i2s' in the
-compatible field.
-
-7) GPIO controller nodes
-Each GPIO controller node should have the empty property gpio-controller and
-#gpio-cells set to 2. First cell is the GPIO number which is interpreted
-according to the bit numbers in the GPIO control registers. The second cell
-is for flags which is currently unsused.
-
-8) FEC nodes
-The FEC node can specify one of the following properties to configure
-the MII link:
-"fsl,7-wire-mode" - An empty property that specifies the link uses 7-wire
-                    mode instead of MII
-"current-speed"   - Specifies that the MII should be configured for a fixed
-                    speed.  This property should contain two cells.  The
-                    first cell specifies the speed in Mbps and the second
-                    should be '0' for half duplex and '1' for full duplex
-"phy-handle"      - Contains a phandle to an Ethernet PHY.
-
-IV - Extra Notes
-================
-
-1. Interrupt mapping
---------------------
-The mpc5200 pic driver splits hardware IRQ numbers into two levels.  The
-split reflects the layout of the PIC hardware itself, which groups
-interrupts into one of three groups; CRIT, MAIN or PERP.  Also, the
-Bestcomm dma engine has it's own set of interrupt sources which are
-cascaded off of peripheral interrupt 0, which the driver interprets as a
-fourth group, SDMA.
-
-The interrupts property for device nodes using the mpc5200 pic consists
-of three cells; <L1 L2 level>
-
-    L1 := [CRIT=0, MAIN=1, PERP=2, SDMA=3]
-    L2 := interrupt number; directly mapped from the value in the
-          "ICTL PerStat, MainStat, CritStat Encoded Register"
-    level := [LEVEL_HIGH=0, EDGE_RISING=1, EDGE_FALLING=2, LEVEL_LOW=3]
-
-2. Shared registers
--------------------
-Some SoC devices share registers between them.  ie. the i2c devices use
-a single clock control register, and almost all device are affected by
-the port_config register.  Devices which need to manipulate shared regs
-should look to the parent SoC node.  The soc node is responsible
-for arbitrating all shared register access.
diff --git a/Documentation/video4linux/v4lgrab.c b/Documentation/video4linux/v4lgrab.c
index 079b628481cf..d6e70bef8ad0 100644
--- a/Documentation/video4linux/v4lgrab.c
+++ b/Documentation/video4linux/v4lgrab.c
@@ -4,12 +4,21 @@
  *
  *	Compile with:
  *		gcc -s -Wall -Wstrict-prototypes v4lgrab.c -o v4lgrab
- *      Use as:
- *              v4lgrab >image.ppm
+ *	Use as:
+ *		v4lgrab >image.ppm
  *
  *	Copyright (C) 1998-05-03, Phil Blundell <philb@gnu.org>
- *      Copied from http://www.tazenda.demon.co.uk/phil/vgrabber.c
- *      with minor modifications (Dave Forrest, drf5n@virginia.edu).
+ *	Copied from http://www.tazenda.demon.co.uk/phil/vgrabber.c
+ *	with minor modifications (Dave Forrest, drf5n@virginia.edu).
+ *
+ *
+ *	For some cameras you may need to pre-load libv4l to perform
+ *	the necessary decompression, e.g.:
+ *
+ *	export LD_PRELOAD=/usr/lib/libv4l/v4l1compat.so
+ *	./v4lgrab >image.ppm
+ *
+ *	see http://hansdegoede.livejournal.com/3636.html for details.
  *
  */
 
@@ -24,7 +33,7 @@
 #include <linux/types.h>
 #include <linux/videodev.h>
 
-#define FILE "/dev/video0"
+#define VIDEO_DEV "/dev/video0"
 
 /* Stole this from tvset.c */
 
@@ -90,7 +99,7 @@ int get_brightness_adj(unsigned char *image, long size, int *brightness) {
 
 int main(int argc, char ** argv)
 {
-  int fd = open(FILE, O_RDONLY), f;
+  int fd = open(VIDEO_DEV, O_RDONLY), f;
   struct video_capability cap;
   struct video_window win;
   struct video_picture vpic;
@@ -100,13 +109,13 @@ int main(int argc, char ** argv)
   unsigned int i, src_depth;
 
   if (fd < 0) {
-    perror(FILE);
+    perror(VIDEO_DEV);
     exit(1);
   }
 
   if (ioctl(fd, VIDIOCGCAP, &cap) < 0) {
     perror("VIDIOGCAP");
-    fprintf(stderr, "(" FILE " not a video4linux device?)\n");
+    fprintf(stderr, "(" VIDEO_DEV " not a video4linux device?)\n");
     close(fd);
     exit(1);
   }