Merge remote-tracking branch 'regulator/fix/s5m8767' into regulator-linus

6 files changed, 372 insertions, 7 deletions

diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt
new file mode 100644
index 000000000000..11921cc417bf
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/max77693.txt
@@ -0,0 +1,55 @@
+Maxim MAX77693 multi-function device
+
+MAX77693 is a Multifunction device with the following submodules:
+- PMIC,
+- CHARGER,
+- LED,
+- MUIC,
+- HAPTIC
+
+It is interfaced to host controller using i2c.
+This document describes the bindings for the mfd device.
+
+Required properties:
+- compatible : Must be "maxim,max77693".
+- reg : Specifies the i2c slave address of PMIC block.
+- interrupts : This i2c device has an IRQ line connected to the main SoC.
+- interrupt-parent :  The parent interrupt controller.
+
+Optional properties:
+- regulators : The regulators of max77693 have to be instantiated under subnod
+  named "regulators" using the following format.
+
+	regulators {
+		regualtor-compatible = ESAFEOUT1/ESAFEOUT2/CHARGER
+		standard regulator constratints[*].
+	};
+
+	[*] refer Documentation/devicetree/bindings/regulator/regulator.txt
+
+Example:
+	max77693@66 {
+		compatible = "maxim,max77693";
+		reg = <0x66>;
+		interrupt-parent = <&gpx1>;
+		interrupts = <5 2>;
+
+		regulators {
+			esafeout@1 {
+				regulator-compatible = "ESAFEOUT1";
+				regulator-name = "ESAFEOUT1";
+				regulator-boot-on;
+			};
+			esafeout@2 {
+				regulator-compatible = "ESAFEOUT2";
+				regulator-name = "ESAFEOUT2";
+				};
+			charger@0 {
+				regulator-compatible = "CHARGER";
+				regulator-name = "CHARGER";
+				regulator-min-microamp = <60000>;
+				regulator-max-microamp = <2580000>;
+					regulator-boot-on;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/regulator/lp872x.txt b/Documentation/devicetree/bindings/regulator/lp872x.txt
new file mode 100644
index 000000000000..78183182dad9
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/lp872x.txt
@@ -0,0 +1,160 @@
+Binding for TI/National Semiconductor LP872x Driver
+
+Required properties:
+  - compatible: "ti,lp8720" or "ti,lp8725"
+  - reg: I2C slave address. 0x7d = LP8720, 0x7a = LP8725
+
+Optional properties:
+  - ti,general-config: the value of LP872X_GENERAL_CFG register (u8)
+    (LP8720)
+    bit[2]: BUCK output voltage control by external DVS pin or register
+            1 = external pin, 0 = bit7 of register 08h
+    bit[1]: sleep control by external DVS pin or register
+            1 = external pin, 0 = bit6 of register 08h
+    bit[0]: time step unit(usec). 1 = 25, 0 = 50
+
+    (LP8725)
+    bit[7:6]: time step unit(usec). 00 = 32, 01 = 64, 10 = 128, 11 = 256
+    bit[4]:   BUCK2 enable control. 1 = enable, 0 = disable
+    bit[3]:   BUCK2 output voltage register address. 1 = 0Ah, 0 = 0Bh
+    bit[2]:   BUCK1 output voltage control by external DVS pin or register
+              1 = register 08h, 0 = DVS
+    bit[1]:   LDO sleep control. 1 = sleep mode, 0 = normal
+    bit[0]:   BUCK1 enable control, 1 = enable, 0 = disable
+
+    For more details, please see the datasheet.
+
+  - ti,update-config: define it when LP872X_GENERAL_CFG register should be set
+  - ti,dvs-gpio: GPIO specifier for external DVS pin control of LP872x devices.
+  - ti,dvs-vsel: DVS selector. 0 = SEL_V1, 1 = SEL_V2.
+  - ti,dvs-state: initial DVS pin state. 0 = DVS_LOW, 1 = DVS_HIGH.
+
+  Sub nodes for regulator_init_data
+    LP8720 has maximum 6 nodes. (child name: ldo1 ~ 5 and buck)
+    LP8725 has maximum 9 nodes. (child name: ldo1 ~ 5, lilo1,2 and buck1,2)
+    For more details, please see the following binding document.
+    (Documentation/devicetree/bindings/regulator/regulator.txt)
+
+Datasheet
+  - LP8720: http://www.ti.com/lit/ds/symlink/lp8720.pdf
+  - LP8725: http://www.ti.com/lit/ds/symlink/lp8725.pdf
+
+Example 1) LP8720
+
+lp8720@7d {
+	compatible = "ti,lp8720";
+	reg = <0x7d>;
+
+	/* external DVS pin used, timestep is 25usec */
+	ti,general-config = /bits/ 8 <0x03>;
+	ti,update-config;
+
+	/*
+	 * The dvs-gpio depends on the processor environment.
+	 * For example, following GPIO specifier means GPIO134 in OMAP4.
+	 */
+	ti,dvs-gpio = <&gpio5 6 0>;
+	ti,dvs-vsel = /bits/ 8 <1>;		/* SEL_V2 */
+	ti,dvs-state = /bits/ 8 <1>;		/* DVS_HIGH */
+
+	vaf: ldo1 {
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vmmc: ldo2 {
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vcam_io: ldo3 {
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+	};
+
+	vcam_core: ldo4 {
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <2850000>;
+		regulator-boot-on;
+	};
+
+	vcam: ldo5 {
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vcc: buck {
+		regulator-name = "VBUCK";
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <2300000>;
+	};
+};
+
+Example 2) LP8725
+
+lp8725@7a {
+	compatible = "ti,lp8725";
+	reg = <0x7a>;
+
+	/* Enable BUCK1,2, no DVS, normal LDO mode, timestep is 256usec */
+	ti,general-config = /bits/ 8 <0xdd>;
+	ti,update-config;
+
+	vcam_io: ldo1 {
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vcam_core: ldo2 {
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vcam: ldo3 {
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vcmmb_io: ldo4 {
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+	};
+
+	vcmmb_core: ldo5 {
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+	};
+
+	vaux1: lilo1 {
+		regulator-name = "VAUX1";
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vaux2: lilo2 {
+		regulator-name = "VAUX2";
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vcc1: buck1 {
+		regulator-name = "VBUCK1";
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <3000000>;
+		regulator-min-microamp  = <460000>;
+		regulator-max-microamp  = <1370000>;
+		regulator-boot-on;
+	};
+
+	vcc2: buck2 {
+		regulator-name = "VBUCK2";
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <3000000>;
+		regulator-min-microamp  = <460000>;
+		regulator-max-microamp  = <1370000>;
+		regulator-boot-on;
+	};
+};
diff --git a/Documentation/devicetree/bindings/regulator/max8973-regulator.txt b/Documentation/devicetree/bindings/regulator/max8973-regulator.txt
new file mode 100644
index 000000000000..4f15d8a1bfd0
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/max8973-regulator.txt
@@ -0,0 +1,21 @@
+* Maxim MAX8973 Voltage Regulator
+
+Required properties:
+
+- compatible:	must be "maxim,max8973"
+- reg:		the i2c slave address of the regulator. It should be 0x1b.
+
+Any standard regulator properties can be used to configure the single max8973
+DCDC.
+
+Example:
+
+	max8973@1b {
+		compatible = "maxim,max8973";
+		reg = <0x1b>;
+
+		regulator-min-microvolt = <935000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt
index ecfc6ccd67ef..48a3b8e5d6bd 100644
--- a/Documentation/devicetree/bindings/regulator/regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/regulator.txt
@@ -9,6 +9,7 @@ Optional properties:
 - regulator-max-microamp: largest current consumers may set
 - regulator-always-on: boolean, regulator should never be disabled
 - regulator-boot-on: bootloader/firmware enabled regulator
+- regulator-allow-bypass: allow the regulator to go into bypass mode
 - <name>-supply: phandle to the parent supply/regulator node
 - regulator-ramp-delay: ramp delay for regulator(in uV/uS)
 
diff --git a/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt b/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt
index a35ff99003a5..d1660a90fc06 100644
--- a/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt
@@ -1,6 +1,6 @@
 * Samsung S5M8767 Voltage and Current Regulator
 
-The Samsung S5M8767 is a multi-function device which includes volatage and
+The Samsung S5M8767 is a multi-function device which includes voltage and
 current regulators, rtc, charger controller and other sub-blocks. It is
 interfaced to the host controller using a i2c interface. Each sub-block is
 addressed by the host system using different i2c slave address. This document
@@ -103,13 +103,13 @@ Example:
 
 		s5m8767,pmic-buck-default-dvs-idx = <0>;
 
-		s5m8767,pmic-buck-dvs-gpios = <&gpx0 0 1 0 0>, /* DVS1 */
-						 <&gpx0 1 1 0 0>, /* DVS2 */
-						 <&gpx0 2 1 0 0>; /* DVS3 */
+		s5m8767,pmic-buck-dvs-gpios = <&gpx0 0 0>, /* DVS1 */
+						 <&gpx0 1 0>, /* DVS2 */
+						 <&gpx0 2 0>; /* DVS3 */
 
-		s5m8767,pmic-buck-ds-gpios = <&gpx2 3 1 0 0>, /* SET1 */
-						<&gpx2 4 1 0 0>, /* SET2 */
-						<&gpx2 5 1 0 0>; /* SET3 */
+		s5m8767,pmic-buck-ds-gpios = <&gpx2 3 0>, /* SET1 */
+						<&gpx2 4 0>, /* SET2 */
+						<&gpx2 5 0>; /* SET3 */
 
 		s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>,
 						 <1250000>, <1200000>,
diff --git a/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt b/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt
new file mode 100644
index 000000000000..2e57a33e9029
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt
@@ -0,0 +1,128 @@
+Adaptive Body Bias(ABB) SoC internal LDO regulator for Texas Instruments SoCs
+
+Required Properties:
+- compatible: Should be one of:
+  - "ti,abb-v1" for older SoCs like OMAP3
+  - "ti,abb-v2" for newer SoCs like OMAP4, OMAP5
+- reg: Address and length of the register set for the device. It contains
+  the information of registers in the same order as described by reg-names
+- reg-names: Should contain the reg names
+  - "base-address"	- contains base address of ABB module
+  - "int-address"	- contains address of interrupt register for ABB module
+  (also see Optional properties)
+- #address-cell: should be 0
+- #size-cell: should be 0
+- clocks: should point to the clock node used by ABB module
+- ti,settling-time: Settling time in uSecs from SoC documentation for ABB module
+	to settle down(target time for SR2_WTCNT_VALUE).
+- ti,clock-cycles: SoC specific data about count of system ti,clock-cycles used for
+	computing settling time from SoC Documentation for ABB module(clock
+	cycles for SR2_WTCNT_VALUE).
+- ti,tranxdone-status-mask: Mask to the int-register to write-to-clear mask
+	indicating LDO tranxdone (operation complete).
+- ti,abb_info: An array of 6-tuples u32 items providing information about ABB
+	configuration needed per operational voltage of the device.
+	Each item consists of the following in the same order:
+	volt: voltage in uV - Only used to index ABB information.
+	ABB mode: one of the following:
+		0-bypass
+		1-Forward Body Bias(FBB)
+		3-Reverse Body Bias(RBB)
+	efuse:	(see Optional properties)
+	RBB enable efuse Mask:	(See Optional properties)
+	FBB enable efuse Mask:	(See Optional properties)
+	Vset value efuse Mask:	(See Optional properties)
+
+	NOTE: If more than 1 entry is present, then regulator is setup to change
+	      voltage, allowing for various modes to be selected indexed off
+	      the regulator. Further, ABB LDOs are considered always-on by
+	      default.
+
+Optional Properties:
+- reg-names: In addition to the required properties, the following are optional
+  - "efuse-address"	- Contains efuse base address used to pick up ABB info.
+  - "ldo-address"	- Contains address of ABB LDO overide register address.
+	"efuse-address" is required for this.
+- ti,ldovbb-vset-mask	- Required if ldo-address is set, mask for LDO override
+	register to provide override vset value.
+- ti,ldovbb-override-mask - Required if ldo-address is set, mask for LDO
+	override register to enable override vset value.
+- ti,abb_opp_sel: Addendum to the description in required properties
+	efuse: Mandatory if 'efuse-address' register is defined. Provides offset
+	       from efuse-address to pick up ABB characteristics. Set to 0 if
+	       'efuse-address' is not defined.
+	RBB enable efuse Mask:	Optional if 'efuse-address' register is defined.
+		'ABB mode' is force set to RBB mode if value at "efuse-address"
+		+ efuse maps to RBB mask. Set to 0 to ignore this.
+	FBB enable efuse Mask:	Optional if 'efuse-address' register is defined.
+		'ABB mode' is force set to FBB mode if value at "efuse-address"
+		+ efuse maps to FBB mask (valid only if RBB mask does not match)
+		Set to 0 to ignore this.
+	Vset value efuse Mask:	Mandatory if ldo-address is set. Picks up from
+		efuse the value to set in 'ti,ldovbb-vset-mask' at ldo-address.
+
+Example #1: Simplest configuration (no efuse data, hard coded ABB table):
+abb_x: regulator-abb-x {
+	compatible = "ti,abb-v1";
+	regulator-name = "abb_x";
+	#address-cell = <0>;
+	#size-cells = <0>;
+	reg = <0x483072f0 0x8>, <0x48306818 0x4>;
+	reg-names = "base-address", "int-address";
+	ti,tranxdone-status-mask = <0x4000000>;
+	clocks = <&sysclk>;
+	ti,settling-time = <30>;
+	ti,clock-cycles = <8>;
+	ti,abb_info = <
+	/* uV		ABB	efuse	rbb_m	fbb_m	vset_m */
+	1012500		0	0	0	0	0 /* Bypass */
+	1200000		3	0	0	0	0 /* RBB mandatory */
+	1320000		1	0	0	0	0 /* FBB mandatory */
+	>;
+};
+
+Example #2: Efuse bits contain ABB mode setting (no LDO override capability)
+abb_y: regulator-abb-y {
+	compatible = "ti,abb-v2";
+	regulator-name = "abb_y";
+	#address-cell = <0>;
+	#size-cells = <0>;
+	reg = <0x4a307bd0 0x8>, <0x4a306014 0x4>, <0x4A002268 0x8>;
+	reg-names = "base-address", "int-address", "efuse-address";
+	ti,tranxdone-status-mask = <0x4000000>;
+	clocks = <&sysclk>;
+	ti,settling-time = <50>;
+	ti,clock-cycles = <16>;
+	ti,abb_info = <
+	/* uV		ABB	efuse	rbb_m	fbb_m	vset_m */
+	975000		0	0	0	0	0 /* Bypass */
+	1012500		0	0	0x40000	0	0 /* RBB optional */
+	1200000		0	0x4	0	0x40000	0 /* FBB optional */
+	1320000		1	0	0	0	0 /* FBB mandatory */
+	>;
+};
+
+Example #3: Efuse bits contain ABB mode setting and LDO override capability
+abb_z: regulator-abb-z {
+	compatible = "ti,abb-v2";
+	regulator-name = "abb_z";
+	#address-cell = <0>;
+	#size-cells = <0>;
+	reg = <0x4ae07ce4 0x8>, <0x4ae06010 0x4>,
+	      <0x4a002194 0x8>, <0x4ae0C314 0x4>;
+	reg-names = "base-address", "int-address",
+		    "efuse-address", "ldo-address";
+	ti,tranxdone-status-mask = <0x8000000>;
+	/* LDOVBBMM_MUX_CTRL */
+	ti,ldovbb-override-mask = <0x400>;
+	/* LDOVBBMM_VSET_OUT */
+	ti,ldovbb-vset-mask = <0x1F>;
+	clocks = <&sysclk>;
+	ti,settling-time = <50>;
+	ti,clock-cycles = <16>;
+	ti,abb_info = <
+	/* uV	ABB	efuse	rbb_m	fbb_m	vset_m */
+	975000	0	0	0	0	0	/* Bypass */
+	1200000	0	0x4	0	0x40000	0x1f00	/* FBB optional, vset */
+	>;
+};