diff options
| author | Russell King <rmk+kernel@arm.linux.org.uk> | 2013-09-27 20:07:26 +0100 |
|---|---|---|
| committer | Russell King <rmk+kernel@arm.linux.org.uk> | 2014-01-27 14:18:09 +0000 |
| commit | 208d7baf8085ed639ec896274f1679d4718f2ff3 (patch) | |
| tree | ad5ec8c11c35d27f9beca7e602e3ccb921cd9d63 /arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi | |
| parent | d8ec26d7f8287f5788a494f56e8814210f0e64be (diff) | |
ARM: imx: initial SolidRun HummingBoard support
Add support for the SolidRun HummingBoard. This commit adds support for
the following interfaces on this board:
- Consumer Ir receiver
- S/PDIF output
- Both USB interfaces
- Gigabit Ethernet using AR8035
- UART port
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Diffstat (limited to 'arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi')
| -rw-r--r-- | arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi | 62 |
1 files changed, 62 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi b/arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi new file mode 100644 index 000000000000..a3cb2fff8f61 --- /dev/null +++ b/arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi @@ -0,0 +1,62 @@ +/* + * Copyright (C) 2013,2014 Russell King + * + * This describes the hookup for an AR8035 to the iMX6 on the SolidRun + * MicroSOM. + */ +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_microsom_enet_ar8035>; + phy-mode = "rgmii"; + phy-reset-duration = <2>; + phy-reset-gpios = <&gpio4 15 0>; + status = "okay"; +}; + +&iomuxc { + enet { + pinctrl_microsom_enet_ar8035: microsom-enet-ar8035 { + fsl,pins = < + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + /* AR8035 reset */ + MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x130b0 + /* AR8035 interrupt */ + MX6QDL_PAD_DI0_PIN2__GPIO4_IO18 0x80000000 + /* GPIO16 -> AR8035 25MHz */ + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0xc0000000 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x80000000 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 + /* AR8035 CLK_25M --> ENET_REF_CLK (V22) */ + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x0a0b1 + /* AR8035 pin strapping: IO voltage: pull up */ + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + /* AR8035 pin strapping: PHYADDR#0: pull down */ + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x130b0 + /* AR8035 pin strapping: PHYADDR#1: pull down */ + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x130b0 + /* AR8035 pin strapping: MODE#1: pull up */ + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + /* AR8035 pin strapping: MODE#3: pull up */ + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + /* AR8035 pin strapping: MODE#0: pull down */ + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x130b0 + + /* + * As the RMII pins are also connected to RGMII + * so that an AR8030 can be placed, set these + * to high-z with the same pulls as above. + * Use the GPIO settings to avoid changing the + * input select registers. + */ + MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x03000 + MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x03000 + MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x03000 + >; + }; + }; +}; |