ARM: dts: imx6qdl: make pinctrl nodes board specific

Currently, all pinctrl setting nodes are defined in <soc>.dtsi, so that
boards that share the same pinctrl setting do not have to define it time
and time again in <board>.dts.  However, along with the devices and use
cases being added continuously, the pinctrl setting nodes under iomuxc
becomes more than expected.  This bloats device tree blob for particular
board unnecessarily since only a small subset of those pinctrl setting
nodes will be used by the board.  It impacts not only the DTB file size
but also the run-time device tree lookup efficiency.

The patch moves all the pinctrl data into individual boards as needed.
With the changes, the pinctrl setting nodes becomes local to particular
board, and it makes no sense to continue numbering the setting for
given peripheral.  Thus, all the pinctrl phandler name gets updated to
have only peripheral name in there.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

1 files changed, 112 insertions, 11 deletions

diff --git a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
index e75e11b36dff..4a7997e42b59 100644
--- a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
@@ -92,7 +92,7 @@
 
 &audmux {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_audmux_2>;
+	pinctrl-0 = <&pinctrl_audmux>;
 	status = "okay";
 };
 
@@ -100,7 +100,7 @@
 	fsl,spi-num-chipselects = <1>;
 	cs-gpios = <&gpio4 9 0>;
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi1_2>;
+	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
 	flash: m25p80@0 {
@@ -114,7 +114,7 @@
 
 &fec {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_enet_1>;
+	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii";
 	phy-reset-gpios = <&gpio1 25 0>;
 	status = "okay";
@@ -123,7 +123,7 @@
 &i2c1 {
 	clock-frequency = <100000>;
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c1_2>;
+	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
 	codec: wm8962@1a {
@@ -152,7 +152,7 @@
 &i2c3 {
 	clock-frequency = <100000>;
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c3_2>;
+	pinctrl-0 = <&pinctrl_i2c3>;
 	status = "okay";
 
 	egalax_ts@04 {
@@ -168,7 +168,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hog>;
 
-	hog {
+	imx6qdl-sabresd {
 		pinctrl_hog: hoggrp {
 			fsl,pins = <
 				MX6QDL_PAD_GPIO_4__GPIO1_IO04   0x80000000
@@ -184,6 +184,107 @@
 				MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x80000000
 			>;
 		};
+
+		pinctrl_audmux: audmuxgrp {
+			fsl,pins = <
+				MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x80000000
+				MX6QDL_PAD_CSI0_DAT4__AUD3_TXC		0x80000000
+				MX6QDL_PAD_CSI0_DAT5__AUD3_TXD		0x80000000
+				MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x80000000
+			>;
+		};
+
+		pinctrl_ecspi1: ecspi1grp {
+			fsl,pins = <
+				MX6QDL_PAD_KEY_COL1__ECSPI1_MISO	0x100b1
+				MX6QDL_PAD_KEY_ROW0__ECSPI1_MOSI	0x100b1
+				MX6QDL_PAD_KEY_COL0__ECSPI1_SCLK	0x100b1
+			>;
+		};
+
+		pinctrl_enet: enetgrp {
+			fsl,pins = <
+				MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+				MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+				MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b0b0
+				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b0b0
+				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b0b0
+				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b0b0
+				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b0b0
+				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b0b0
+				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
+				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b0b0
+				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b0b0
+				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b0b0
+				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b0b0
+				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b0b0
+				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b0b0
+				MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
+			>;
+		};
+
+		pinctrl_i2c1: i2c1grp {
+			fsl,pins = <
+				MX6QDL_PAD_CSI0_DAT8__I2C1_SDA		0x4001b8b1
+				MX6QDL_PAD_CSI0_DAT9__I2C1_SCL		0x4001b8b1
+			>;
+		};
+
+		pinctrl_i2c3: i2c3grp {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_3__I2C3_SCL		0x4001b8b1
+				MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
+			>;
+		};
+
+		pinctrl_pwm1: pwm1grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT3__PWM1_OUT		0x1b0b1
+			>;
+		};
+
+		pinctrl_uart1: uart1grp {
+			fsl,pins = <
+				MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA	0x1b0b1
+				MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA	0x1b0b1
+			>;
+		};
+
+		pinctrl_usbotg: usbotggrp {
+			fsl,pins = <
+				MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID	0x17059
+			>;
+		};
+
+		pinctrl_usdhc2: usdhc2grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
+				MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
+				MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+				MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+				MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+				MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+				MX6QDL_PAD_NANDF_D4__SD2_DATA4		0x17059
+				MX6QDL_PAD_NANDF_D5__SD2_DATA5		0x17059
+				MX6QDL_PAD_NANDF_D6__SD2_DATA6		0x17059
+				MX6QDL_PAD_NANDF_D7__SD2_DATA7		0x17059
+			>;
+		};
+
+		pinctrl_usdhc3: usdhc3grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+				MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+				MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+				MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+				MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+				MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+				MX6QDL_PAD_SD3_DAT4__SD3_DATA4		0x17059
+				MX6QDL_PAD_SD3_DAT5__SD3_DATA5		0x17059
+				MX6QDL_PAD_SD3_DAT6__SD3_DATA6		0x17059
+				MX6QDL_PAD_SD3_DAT7__SD3_DATA7		0x17059
+			>;
+		};
 	};
 };
 
@@ -214,7 +315,7 @@
 
 &pwm1 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm0_1>;
+	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
 };
 
@@ -225,7 +326,7 @@
 
 &uart1 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1_1>;
+	pinctrl-0 = <&pinctrl_uart1>;
 	status = "okay";
 };
 
@@ -237,14 +338,14 @@
 &usbotg {
 	vbus-supply = <&reg_usb_otg_vbus>;
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usbotg_2>;
+	pinctrl-0 = <&pinctrl_usbotg>;
 	disable-over-current;
 	status = "okay";
 };
 
 &usdhc2 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc2_1>;
+	pinctrl-0 = <&pinctrl_usdhc2>;
 	bus-width = <8>;
 	cd-gpios = <&gpio2 2 0>;
 	wp-gpios = <&gpio2 3 0>;
@@ -253,7 +354,7 @@
 
 &usdhc3 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc3_1>;
+	pinctrl-0 = <&pinctrl_usdhc3>;
 	bus-width = <8>;
 	cd-gpios = <&gpio2 0 0>;
 	wp-gpios = <&gpio2 1 0>;