Merge tag 'omap-for-v3.13/dt-late' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt

Some more dts changes from Benoit Cousson <bcousson@baylibre.com> via
Tony Lindgren:

- Add a lot of N900 nodes
- Add OPP table to OMAP5/DRA7
- Add support for Newflow NanoBone board
- Add i2c aliases
- Add McASP and audio support
- Add reset/idle on init bindings for OMAP
- Add more nodes for AM4272

* tag 'omap-for-v3.13/dt-late' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (42 commits)
  ARM: dts: omap5-uevm: Remove pinmux for dmic pins
  ARM: dts: omap5-uevm: Correct twl6040 reset GPIO pinmux
  ARM: dts: TWL4030: Add power button support
  ARM: dts: omap3-n900: Add LP5523 support
  ARM: dts: omap3-n900: Add TLV320AIC3X support
  ARM: dts: omap3-n900:: Mux RX51_LCD_RESET_GPIO in DTS
  ARM: dts: omap3-n900: Add NAND support
  ARM: dts: omap3-n900: Specify regulator info
  ARM: dts: TWL4030: Add missing regulators
  ARM: dts: omap3-n900: Add LP5523 support
  ARM: dts: omap3-n900: Add vibrator device
  ARM: dts: omap3-n900: GPIO key definitions
  ARM: dts: omap3-n900: Add support for SD cards
  ARM: dts: omap3-n900: Add UART support
  ARM: dts: omap3-n900: Fix i2c bus speed
  ARM: dts: omap3-n900: Add pinctrl for i2c devices
  ARM: dts: DRA7: Add CPU OPP table
  ARM: dts: OMAP5: Add CPU OPP table
  ARM: dts: dra7-evm: add smps123 supply for CPU
  ARM: dts: omap5-uevm: add smps123 supply for CPU
  ...

Signed-off-by: Olof Johansson <olof@lixom.net>

20 files changed, 1547 insertions, 36 deletions

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index f2ff6266f789..b590bcebaa68 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -197,6 +197,7 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	am335x-evmsk.dtb \
 	am335x-bone.dtb \
 	am335x-boneblack.dtb \
+	am335x-nano.dtb \
 	am335x-base0033.dtb \
 	am3517-evm.dtb \
 	am3517_mt_ventoux.dtb \
diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/am335x-evm.dts
index eabacf9b8c31..987429436171 100644
--- a/arch/arm/boot/dts/am335x-evm.dts
+++ b/arch/arm/boot/dts/am335x-evm.dts
@@ -119,6 +119,19 @@
 			};
 		};
 	};
+
+	sound {
+		compatible = "ti,da830-evm-audio";
+		ti,model = "AM335x-EVM";
+		ti,audio-codec = <&tlv320aic3106>;
+		ti,mcasp-controller = <&mcasp1>;
+		ti,codec-clock-rate = <12000000>;
+		ti,audio-routing =
+			"Headphone Jack",       "HPLOUT",
+			"Headphone Jack",       "HPROUT",
+			"LINE1L",               "Line In",
+			"LINE1R",               "Line In";
+	};
 };
 
 &am33xx_pinmux {
@@ -279,6 +292,15 @@
 			0xec 0x00	/* lcd_ac_bias_en.lcd_ac_bias_en, OUTPUT | MODE0 */
 		>;
 	};
+
+	am335x_evm_audio_pins: am335x_evm_audio_pins {
+		pinctrl-single,pins = <
+			0x10c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_rx_dv.mcasp1_aclkx */
+			0x110 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_txd3.mcasp1_fsx */
+			0x108 (PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* mii1_col.mcasp1_axr2 */
+			0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */
+		>;
+	};
 };
 
 &uart0 {
@@ -373,6 +395,18 @@
 		compatible = "ti,tmp275";
 		reg = <0x48>;
 	};
+
+	tlv320aic3106: tlv320aic3106@1b {
+		compatible = "ti,tlv320aic3106";
+		reg = <0x1b>;
+		status = "okay";
+
+		/* Regulators */
+		AVDD-supply = <&vaux2_reg>;
+		IOVDD-supply = <&vaux2_reg>;
+		DRVDD-supply = <&vaux2_reg>;
+		DVDD-supply = <&vbat>;
+	};
 };
 
 &lcdc {
@@ -476,6 +510,22 @@
 
 #include "tps65910.dtsi"
 
+&mcasp1 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&am335x_evm_audio_pins>;
+
+		status = "okay";
+
+		op-mode = <0>;          /* MCASP_IIS_MODE */
+		tdm-slots = <2>;
+		/* 4 serializers */
+		serial-dir = <  /* 0: INACTIVE, 1: TX, 2: RX */
+			0 0 1 2
+		>;
+		tx-num-evt = <1>;
+		rx-num-evt = <1>;
+};
+
 &tps {
 	vcc1-supply = <&vbat>;
 	vcc2-supply = <&vbat>;
diff --git a/arch/arm/boot/dts/am335x-evmsk.dts b/arch/arm/boot/dts/am335x-evmsk.dts
index 5f12b28dd593..03febf85fd2f 100644
--- a/arch/arm/boot/dts/am335x-evmsk.dts
+++ b/arch/arm/boot/dts/am335x-evmsk.dts
@@ -115,6 +115,17 @@
 		brightness-levels = <0 58 61 66 75 90 125 170 255>;
 		default-brightness-level = <8>;
 	};
+
+	sound {
+		compatible = "ti,da830-evm-audio";
+		ti,model = "AM335x-EVMSK";
+		ti,audio-codec = <&tlv320aic3106>;
+		ti,mcasp-controller = <&mcasp1>;
+		ti,codec-clock-rate = <24576000>;
+		ti,audio-routing =
+			"Headphone Jack",       "HPLOUT",
+			"Headphone Jack",       "HPROUT";
+	};
 };
 
 &am33xx_pinmux {
@@ -244,6 +255,15 @@
 			0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
 		>;
 	};
+
+	mcasp1_pins: mcasp1_pins {
+		pinctrl-single,pins = <
+			0x10c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_crs.mcasp1_aclkx */
+			0x110 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_rxerr.mcasp1_fsx */
+			0x108 (PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* mii1_col.mcasp1_axr2 */
+			0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */
+		>;
+	};
 };
 
 &uart0 {
@@ -291,6 +311,18 @@
 		st,max-limit-y = <550>;
 		st,max-limit-z = <750>;
 	};
+
+	tlv320aic3106: tlv320aic3106@1b {
+		compatible = "ti,tlv320aic3106";
+		reg = <0x1b>;
+		status = "okay";
+
+		/* Regulators */
+		AVDD-supply = <&vaux2_reg>;
+		IOVDD-supply = <&vaux2_reg>;
+		DRVDD-supply = <&vaux2_reg>;
+		DVDD-supply = <&vbat>;
+	};
 };
 
 &usb {
@@ -433,3 +465,23 @@
 &aes {
 	status = "okay";
 };
+
+&gpio0 {
+	ti,no-reset-on-init;
+};
+
+&mcasp1 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&mcasp1_pins>;
+
+		status = "okay";
+
+		op-mode = <0>;          /* MCASP_IIS_MODE */
+		tdm-slots = <2>;
+		/* 4 serializers */
+		serial-dir = <  /* 0: INACTIVE, 1: TX, 2: RX */
+			0 0 1 2
+		>;
+		tx-num-evt = <1>;
+		rx-num-evt = <1>;
+};
diff --git a/arch/arm/boot/dts/am335x-igep0033.dtsi b/arch/arm/boot/dts/am335x-igep0033.dtsi
index 06eba076bfcd..619624479311 100644
--- a/arch/arm/boot/dts/am335x-igep0033.dtsi
+++ b/arch/arm/boot/dts/am335x-igep0033.dtsi
@@ -44,6 +44,13 @@
 		regulator-max-microvolt = <5000000>;
 		regulator-boot-on;
 	};
+
+	vmmc: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
 };
 
 &am33xx_pinmux {
@@ -180,6 +187,12 @@
 	};
 };
 
+&mmc1 {
+	status = "okay";
+	vmmc-supply = <&vmmc>;
+	bus-width = <4>;
+};
+
 &uart0 {
 	status = "okay";
 	pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/am335x-nano.dts b/arch/arm/boot/dts/am335x-nano.dts
new file mode 100644
index 000000000000..9907b494b99c
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-nano.dts
@@ -0,0 +1,431 @@
+/*
+ * Copyright (C) 2013 Newflow Ltd - http://www.newflow.co.uk/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+
+/ {
+	model = "Newflow AM335x NanoBone";
+	compatible = "ti,am33xx";
+
+	cpus {
+		cpu@0 {
+			cpu0-supply = <&dcdc2_reg>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>; /* 256 MB */
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led@0 {
+			label = "nanobone:green:usr1";
+			gpios = <&gpio1 5 0>;
+			default-state = "off";
+		};
+	};
+};
+
+&am33xx_pinmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&misc_pins>;
+
+	misc_pins: misc_pins {
+		pinctrl-single,pins = <
+			0x15c (PIN_OUTPUT | MUX_MODE7)	/* spi0_cs0.gpio0_5 */
+		>;
+	};
+
+	gpmc_pins: gpmc_pins {
+		pinctrl-single,pins = <
+			0x0 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad0.gpmc_ad0 */
+			0x4 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad1.gpmc_ad1 */
+			0x8 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad2.gpmc_ad2 */
+			0xc (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad3.gpmc_ad3 */
+			0x10 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad4.gpmc_ad4 */
+			0x14 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad5.gpmc_ad5 */
+			0x18 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad6.gpmc_ad6 */
+			0x1c (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad7.gpmc_ad7 */
+			0x20 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad8.gpmc_ad8 */
+			0x24 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad9.gpmc_ad9 */
+			0x28 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad10.gpmc_ad10 */
+			0x2c (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad11.gpmc_ad11 */
+			0x30 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad12.gpmc_ad12 */
+			0x34 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad13.gpmc_ad13 */
+			0x38 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad14.gpmc_ad14 */
+			0x3c (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad15.gpmc_ad15 */
+
+			0x70 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_wait0.gpmc_wait0 */
+			0x7c (PIN_OUTPUT | MUX_MODE0)		/* gpmc_csn0.gpmc_csn0 */
+			0x80 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_csn1.gpmc_csn1 */
+			0x84 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_csn2.gpmc_csn2 */
+			0x88 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_csn3.gpmc_csn3 */
+
+			0x90 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_advn_ale.gpmc_advn_ale */
+			0x94 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_oen_ren.gpmc_oen_ren */
+			0x98 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_wen.gpmc_wen */
+			0x9c (PIN_OUTPUT | MUX_MODE0)		/* gpmc_ben0_cle.gpmc_ben0_cle */
+
+			0xa4 (PIN_OUTPUT | MUX_MODE1)		/* lcd_data1.gpmc_a1 */
+			0xa8 (PIN_OUTPUT | MUX_MODE1)		/* lcd_data2.gpmc_a2 */
+			0xac (PIN_OUTPUT | MUX_MODE1)		/* lcd_data3.gpmc_a3 */
+			0xb0 (PIN_OUTPUT | MUX_MODE1)		/* lcd_data4.gpmc_a4 */
+			0xb4 (PIN_OUTPUT | MUX_MODE1)		/* lcd_data5.gpmc_a5 */
+			0xb8 (PIN_OUTPUT | MUX_MODE1)		/* lcd_data6.gpmc_a6 */
+			0xbc (PIN_OUTPUT | MUX_MODE1)		/* lcd_data7.gpmc_a7 */
+
+			0xe0 (PIN_OUTPUT | MUX_MODE1)		/* lcd_vsync.gpmc_a8 */
+			0xe4 (PIN_OUTPUT | MUX_MODE1)		/* lcd_hsync.gpmc_a9 */
+			0xe8 (PIN_OUTPUT | MUX_MODE1)		/* lcd_pclk.gpmc_a10 */
+		>;
+	};
+
+	i2c0_pins: i2c0_pins {
+		pinctrl-single,pins = <
+			0x188 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* i2c0_sda.i2c0_sda */
+			0x18c (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* i2c0_scl.i2c0_scl */
+		>;
+	};
+
+	uart0_pins: uart0_pins {
+		pinctrl-single,pins = <
+			0x170 (PIN_INPUT_PULLUP | MUX_MODE0)	/* uart0_rxd.uart0_rxd */
+			0x174 (PIN_OUTPUT | MUX_MODE0)		/* uart0_txd.uart0_txd */
+		>;
+	};
+
+	uart1_pins: uart1_pins {
+		pinctrl-single,pins = <
+			0x178 (PIN_OUTPUT | MUX_MODE7)		/* uart1_ctsn.uart1_ctsn */
+			0x17c (PIN_OUTPUT | MUX_MODE7)		/* uart1_rtsn.uart1_rtsn */
+			0x180 (PIN_INPUT_PULLUP | MUX_MODE0)	/* uart1_rxd.uart1_rxd */
+			0x184 (PIN_OUTPUT | MUX_MODE0)		/* uart1_txd.uart1_txd */
+		>;
+	};
+
+	uart2_pins: uart2_pins {
+		pinctrl-single,pins = <
+			0xc0 (PIN_INPUT_PULLUP | MUX_MODE7)	/* lcd_data8.gpio2[14] */
+			0xc4 (PIN_OUTPUT | MUX_MODE7)		/* lcd_data9.gpio2[15] */
+			0x150 (PIN_INPUT | MUX_MODE1)		/* spi0_sclk.uart2_rxd */
+			0x154 (PIN_OUTPUT | MUX_MODE1)		/* spi0_d0.uart2_txd */
+		>;
+	};
+
+	uart3_pins: uart3_pins {
+		pinctrl-single,pins = <
+			0xc8 (PIN_INPUT_PULLUP | MUX_MODE6)	/* lcd_data10.uart3_ctsn */
+			0xcc (PIN_OUTPUT | MUX_MODE6)		/* lcd_data11.uart3_rtsn */
+			0x160 (PIN_INPUT | MUX_MODE1)		/* spi0_cs1.uart3_rxd */
+			0x164 (PIN_OUTPUT | MUX_MODE1)		/* ecap0_in_pwm0_out.uart3_txd */
+		>;
+	};
+
+	uart4_pins: uart4_pins {
+		pinctrl-single,pins = <
+			0xd0 (PIN_INPUT_PULLUP | MUX_MODE6)	/* lcd_data12.uart4_ctsn */
+			0xd4 (PIN_OUTPUT | MUX_MODE6)		/* lcd_data13.uart4_rtsn */
+			0x168 (PIN_INPUT | MUX_MODE1)		/* uart0_ctsn.uart4_rxd */
+			0x16c (PIN_OUTPUT | MUX_MODE1)		/* uart0_rtsn.uart4_txd */
+		>;
+	};
+
+	uart5_pins: uart5_pins {
+		pinctrl-single,pins = <
+			0xd8 (PIN_INPUT | MUX_MODE4)		/* lcd_data14.uart5_rxd */
+			0x144 (PIN_OUTPUT | MUX_MODE3)		/* rmiii1_refclk.uart5_txd */
+		>;
+	};
+
+	mmc1_pins: mmc1_pins {
+		pinctrl-single,pins = <
+			0xf0 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_dat0.mmc0_dat0 */
+			0xf4 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_dat1.mmc0_dat1 */
+			0xf8 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_dat2.mmc0_dat2 */
+			0xfc (PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_dat3.mmc0_dat3 */
+			0x100 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_clk.mmc0_clk */
+			0x104 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_cmd.mmc0_cmd */
+			0x1e8 (PIN_INPUT_PULLUP | MUX_MODE7)	/* emu1.gpio3[8] */
+			0x1a0 (PIN_INPUT_PULLUP | MUX_MODE7)	/* mcasp0_aclkr.gpio3[18] */
+		>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "okay";
+	rts-gpio = <&gpio0 13 GPIO_ACTIVE_HIGH>;
+	rs485-rts-active-high;
+	rs485-rx-during-tx;
+	rs485-rts-delay = <1 1>;
+	linux,rs485-enabled-at-boot-time;
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	status = "okay";
+	rts-gpio = <&gpio2 15 GPIO_ACTIVE_HIGH>;
+	rs485-rts-active-high;
+	rs485-rts-delay = <1 1>;
+	linux,rs485-enabled-at-boot-time;
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins>;
+	status = "okay";
+};
+
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart5_pins>;
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+
+	gpio@20 {
+		compatible = "mcp,mcp23017";
+		reg = <0x20>;
+	};
+
+	tps: tps@24 {
+		reg = <0x24>;
+	};
+
+	eeprom@53 {
+		compatible = "mcp,24c02";
+		reg = <0x53>;
+		pagesize = <8>;
+	};
+
+	rtc@68 {
+		compatible = "dallas,ds1307";
+		reg = <0x68>;
+	};
+};
+
+&elm {
+	status = "okay";
+};
+
+&gpmc {
+	compatible = "ti,am3352-gpmc";
+	ti,hwmods = "gpmc";
+	status = "okay";
+	gpmc,num-waitpins = <2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpmc_pins>;
+
+	#address-cells = <2>;
+	#size-cells = <1>;
+	ranges = <0 0 0x08000000 0x08000000>;	/* CS0: NOR 128M */
+
+	nor@0,0 {
+		reg = <0 0x00000000 0x08000000>;
+		compatible = "cfi-flash";
+		linux,mtd-name = "spansion,s29gl010p11t";
+		bank-width = <2>;
+
+		gpmc,mux-add-data = <2>;
+
+		gpmc,sync-clk-ps = <0>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <160>;
+		gpmc,cs-wr-off-ns = <160>;
+		gpmc,adv-on-ns = <10>;
+		gpmc,adv-rd-off-ns = <30>;
+		gpmc,adv-wr-off-ns = <30>;
+		gpmc,oe-on-ns = <40>;
+		gpmc,oe-off-ns = <160>;
+		gpmc,we-on-ns = <40>;
+		gpmc,we-off-ns = <160>;
+		gpmc,rd-cycle-ns = <160>;
+		gpmc,wr-cycle-ns = <160>;
+		gpmc,access-ns = <150>;
+		gpmc,page-burst-access-ns = <10>;
+		gpmc,cycle2cycle-samecsen;
+		gpmc,cycle2cycle-delay-ns = <20>;
+		gpmc,wr-data-mux-bus-ns = <70>;
+		gpmc,wr-access-ns = <80>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		/*
+		MTD partition table
+		===================
+		+------------+-->0x00000000-> U-Boot start
+		|            |
+		|            |-->0x000BFFFF-> U-Boot end
+		|            |-->0x000C0000-> ENV1 start
+		|            |
+		|            |-->0x000DFFFF-> ENV1 end
+		|            |-->0x000E0000-> ENV2 start
+		|            |
+		|            |-->0x000FFFFF-> ENV2 end
+		|            |-->0x00100000-> Kernel start
+		|            |
+		|            |-->0x004FFFFF-> Kernel end
+		|            |-->0x00500000-> File system start
+		|            |
+		|            |-->0x014FFFFF-> File system end
+		|            |-->0x01500000-> User data start
+		|            |
+		|            |-->0x03FFFFFF-> User data end
+		|            |-->0x04000000-> Data storage start
+		|            |
+		+------------+-->0x08000000-> NOR end (Free end)
+		*/
+		partition@0 {
+			label = "boot";
+			reg = <0x00000000 0x000c0000>; /* 768KB */
+		};
+
+		partition@1 {
+			label = "env1";
+			reg = <0x000c0000 0x00020000>; /* 128KB */
+		};
+
+		partition@2 {
+			label = "env2";
+			reg = <0x000e0000 0x00020000>; /* 128KB */
+		};
+
+		partition@3 {
+			label = "kernel";
+			reg = <0x00100000 0x00400000>; /* 4MB */
+		};
+
+		partition@4 {
+			label = "rootfs";
+			reg = <0x00500000 0x01000000>; /* 16MB */
+		};
+
+		partition@5 {
+			label = "user";
+			reg = <0x01500000 0x02b00000>; /* 43MB */
+		};
+
+		partition@6 {
+			label = "data";
+			reg = <0x04000000 0x04000000>; /* 64MB */
+		};
+	};
+};
+
+&mac {
+	dual_emac = <1>;
+};
+
+&cpsw_emac0 {
+	phy_id = <&davinci_mdio>, <0>;
+	dual_emac_res_vlan = <1>;
+};
+
+&cpsw_emac1 {
+	phy_id = <&davinci_mdio>, <1>;
+	dual_emac_res_vlan = <2>;
+};
+
+&mmc1 {
+	status = "okay";
+	vmmc-supply = <&ldo4_reg>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	bus-width = <4>;
+	cd-gpios = <&gpio3 8 0>;
+	wp-gpios = <&gpio3 18 0>;
+};
+
+#include "tps65217.dtsi"
+
+&tps {
+	regulators {
+		dcdc1_reg: regulator@0 {
+			/* +1.5V voltage with ±4% tolerance */
+			regulator-min-microvolt = <1450000>;
+			regulator-max-microvolt = <1550000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		dcdc2_reg: regulator@1 {
+			/* VDD_MPU voltage limits 0.95V - 1.1V with ±4% tolerance */
+			regulator-name = "vdd_mpu";
+			regulator-min-microvolt = <915000>;
+			regulator-max-microvolt = <1140000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		dcdc3_reg: regulator@2 {
+			/* VDD_CORE voltage limits 0.95V - 1.1V with ±4% tolerance */
+			regulator-name = "vdd_core";
+			regulator-min-microvolt = <915000>;
+			regulator-max-microvolt = <1140000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		ldo1_reg: regulator@3 {
+			/* +1.8V voltage with ±4% tolerance */
+			regulator-min-microvolt = <1750000>;
+			regulator-max-microvolt = <1870000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		ldo2_reg: regulator@4 {
+			/* +3.3V voltage with ±4% tolerance */
+			regulator-min-microvolt = <3175000>;
+			regulator-max-microvolt = <3430000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		ldo3_reg: regulator@5 {
+			/* +1.8V voltage with ±4% tolerance */
+			regulator-min-microvolt = <1750000>;
+			regulator-max-microvolt = <1870000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		ldo4_reg: regulator@6 {
+			/* +3.3V voltage with ±4% tolerance */
+			regulator-min-microvolt = <3175000>;
+			regulator-max-microvolt = <3430000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
index 7db3c81d1563..0ca13ad92fa6 100644
--- a/arch/arm/boot/dts/am33xx.dtsi
+++ b/arch/arm/boot/dts/am33xx.dtsi
@@ -18,6 +18,9 @@
 	interrupt-parent = <&intc>;
 
 	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
 		serial0 = &uart0;
 		serial1 = &uart1;
 		serial2 = &uart2;
@@ -413,7 +416,7 @@
 			ti,hwmods = "usb_otg_hs";
 			status = "disabled";
 
-			ctrl_mod: control@44e10000 {
+			usb_ctrl_mod: control@44e10000 {
 				compatible = "ti,am335x-usb-ctrl-module";
 				reg = <0x44e10620 0x10
 					0x44e10648 0x4>;
@@ -426,7 +429,7 @@
 				reg = <0x47401300 0x100>;
 				reg-names = "phy";
 				status = "disabled";
-				ti,ctrl_mod = <&ctrl_mod>;
+				ti,ctrl_mod = <&usb_ctrl_mod>;
 			};
 
 			usb0: usb@47401000 {
@@ -474,7 +477,7 @@
 				reg = <0x47401b00 0x100>;
 				reg-names = "phy";
 				status = "disabled";
-				ti,ctrl_mod = <&ctrl_mod>;
+				ti,ctrl_mod = <&usb_ctrl_mod>;
 			};
 
 			usb1: usb@47401800 {
@@ -674,6 +677,7 @@
 			reg = <0x44d00000 0x4000	/* M3 UMEM */
 			       0x44d80000 0x2000>;	/* M3 DMEM */
 			ti,hwmods = "wkup_m3";
+			ti,no-reset-on-init;
 		};
 
 		elm: elm@48080000 {
@@ -713,6 +717,7 @@
 		gpmc: gpmc@50000000 {
 			compatible = "ti,am3352-gpmc";
 			ti,hwmods = "gpmc";
+			ti,no-idle-on-init;
 			reg = <0x50000000 0x2000>;
 			interrupts = <100>;
 			gpmc,num-cs = <7>;
@@ -740,5 +745,33 @@
 			       <&edma 5>;
 			dma-names = "tx", "rx";
 		};
+
+		mcasp0: mcasp@48038000 {
+			compatible = "ti,am33xx-mcasp-audio";
+			ti,hwmods = "mcasp0";
+			reg = <0x48038000 0x2000>,
+			      <0x46000000 0x400000>;
+			reg-names = "mpu", "dat";
+			interrupts = <80>, <81>;
+			interrupts-names = "tx", "rx";
+			status = "disabled";
+			dmas = <&edma 8>,
+				<&edma 9>;
+			dma-names = "tx", "rx";
+		};
+
+		mcasp1: mcasp@4803C000 {
+			compatible = "ti,am33xx-mcasp-audio";
+			ti,hwmods = "mcasp1";
+			reg = <0x4803C000 0x2000>,
+			      <0x46400000 0x400000>;
+			reg-names = "mpu", "dat";
+			interrupts = <82>, <83>;
+			interrupts-names = "tx", "rx";
+			status = "disabled";
+			dmas = <&edma 10>,
+				<&edma 11>;
+			dma-names = "tx", "rx";
+		};
 	};
 };
diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi
index a403172430bc..974d103ab3b1 100644
--- a/arch/arm/boot/dts/am4372.dtsi
+++ b/arch/arm/boot/dts/am4372.dtsi
@@ -18,7 +18,12 @@
 
 
 	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
 		serial0 = &uart0;
+		ethernet0 = &cpsw_emac0;
+		ethernet1 = &cpsw_emac1;
 	};
 
 	cpus {
@@ -39,11 +44,42 @@
 		      <0x48240100 0x0100>;
 	};
 
+	l2-cache-controller@48242000 {
+		compatible = "arm,pl310-cache";
+		reg = <0x48242000 0x1000>;
+		cache-unified;
+		cache-level = <2>;
+	};
+
+	am43xx_pinmux: pinmux@44e10800 {
+		compatible = "pinctrl-single";
+		reg = <0x44e10800 0x31c>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-single,register-width = <32>;
+		pinctrl-single,function-mask = <0xffffffff>;
+	};
+
 	ocp {
 		compatible = "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges;
+		ti,hwmods = "l3_main";
+
+		edma: edma@49000000 {
+			compatible = "ti,edma3";
+			ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2";
+			reg =	<0x49000000 0x10000>,
+				<0x44e10f90 0x10>;
+			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			dma-channels = <64>;
+			ti,edma-regions = <4>;
+			ti,edma-slots = <256>;
+		};
 
 		uart0: serial@44e09000 {
 			compatible = "ti,am4372-uart","ti,omap2-uart";
@@ -92,6 +128,18 @@
 			status = "disabled";
 		};
 
+		mailbox: mailbox@480C8000 {
+			compatible = "ti,omap4-mailbox";
+			reg = <0x480C8000 0x200>;
+			interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "mailbox";
+			ti,mbox-num-users = <4>;
+			ti,mbox-num-fifos = <8>;
+			ti,mbox-names = "wkup_m3";
+			ti,mbox-data = <0 0 0 0>;
+			status = "disabled";
+		};
+
 		timer1: timer@44e31000 {
 			compatible = "ti,am4372-timer-1ms","ti,am335x-timer-1ms";
 			reg = <0x44e31000 0x400>;
@@ -203,7 +251,6 @@
 			reg = <0x44e35000 0x1000>;
 			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "wd_timer2";
-			status = "disabled";
 		};
 
 		gpio0: gpio@44e07000 {
@@ -318,6 +365,40 @@
 			status = "disabled";
 		};
 
+		mmc1: mmc@48060000 {
+			compatible = "ti,omap4-hsmmc";
+			reg = <0x48060000 0x1000>;
+			ti,hwmods = "mmc1";
+			ti,dual-volt;
+			ti,needs-special-reset;
+			dmas = <&edma 24
+				&edma 25>;
+			dma-names = "tx", "rx";
+			interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		mmc2: mmc@481d8000 {
+			compatible = "ti,omap4-hsmmc";
+			reg = <0x481d8000 0x1000>;
+			ti,hwmods = "mmc2";
+			ti,needs-special-reset;
+			dmas = <&edma 2
+				&edma 3>;
+			dma-names = "tx", "rx";
+			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		mmc3: mmc@47810000 {
+			compatible = "ti,omap4-hsmmc";
+			reg = <0x47810000 0x1000>;
+			ti,hwmods = "mmc3";
+			ti,needs-special-reset;
+			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
 		spi1: spi@481a0000 {
 			compatible = "ti,am4372-mcspi","ti,omap4-mcspi";
 			reg = <0x481a0000 0x400>;
@@ -366,50 +447,173 @@
 				      GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH
 				      GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH
 				      GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			ti,hwmods = "cpgmac0";
 			status = "disabled";
+			cpdma_channels = <8>;
+			ale_entries = <1024>;
+			bd_ram_size = <0x2000>;
+			no_bd_ram = <0>;
+			rx_descs = <64>;
+			mac_control = <0x20>;
+			slaves = <2>;
+			active_slave = <0>;
+			cpts_clock_mult = <0x80000000>;
+			cpts_clock_shift = <29>;
+			ranges;
+
+			davinci_mdio: mdio@4a101000 {
+				compatible = "ti,am4372-mdio","ti,davinci_mdio";
+				reg = <0x4a101000 0x100>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				ti,hwmods = "davinci_mdio";
+				bus_freq = <1000000>;
+				status = "disabled";
+			};
+
+			cpsw_emac0: slave@4a100200 {
+				/* Filled in by U-Boot */
+				mac-address = [ 00 00 00 00 00 00 ];
+			};
+
+			cpsw_emac1: slave@4a100300 {
+				/* Filled in by U-Boot */
+				mac-address = [ 00 00 00 00 00 00 ];
+			};
 		};
 
 		epwmss0: epwmss@48300000 {
 			compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
 			reg = <0x48300000 0x10>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
 			ti,hwmods = "epwmss0";
 			status = "disabled";
+
+			ecap0: ecap@48300100 {
+				compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+				reg = <0x48300100 0x80>;
+				ti,hwmods = "ecap0";
+				status = "disabled";
+			};
+
+			ehrpwm0: ehrpwm@48300200 {
+				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				reg = <0x48300200 0x80>;
+				ti,hwmods = "ehrpwm0";
+				status = "disabled";
+			};
 		};
 
 		epwmss1: epwmss@48302000 {
 			compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
 			reg = <0x48302000 0x10>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
 			ti,hwmods = "epwmss1";
 			status = "disabled";
+
+			ecap1: ecap@48302100 {
+				compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+				reg = <0x48302100 0x80>;
+				ti,hwmods = "ecap1";
+				status = "disabled";
+			};
+
+			ehrpwm1: ehrpwm@48302200 {
+				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				reg = <0x48302200 0x80>;
+				ti,hwmods = "ehrpwm1";
+				status = "disabled";
+			};
 		};
 
 		epwmss2: epwmss@48304000 {
 			compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
 			reg = <0x48304000 0x10>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
 			ti,hwmods = "epwmss2";
 			status = "disabled";
+
+			ecap2: ecap@48304100 {
+				compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+				reg = <0x48304100 0x80>;
+				ti,hwmods = "ecap2";
+				status = "disabled";
+			};
+
+			ehrpwm2: ehrpwm@48304200 {
+				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				reg = <0x48304200 0x80>;
+				ti,hwmods = "ehrpwm2";
+				status = "disabled";
+			};
 		};
 
 		epwmss3: epwmss@48306000 {
 			compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
 			reg = <0x48306000 0x10>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
 			ti,hwmods = "epwmss3";
 			status = "disabled";
+
+			ehrpwm3: ehrpwm@48306200 {
+				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				reg = <0x48306200 0x80>;
+				ti,hwmods = "ehrpwm3";
+				status = "disabled";
+			};
 		};
 
 		epwmss4: epwmss@48308000 {
 			compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
 			reg = <0x48308000 0x10>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
 			ti,hwmods = "epwmss4";
 			status = "disabled";
+
+			ehrpwm4: ehrpwm@48308200 {
+				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				reg = <0x48308200 0x80>;
+				ti,hwmods = "ehrpwm4";
+				status = "disabled";
+			};
 		};
 
 		epwmss5: epwmss@4830a000 {
 			compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
 			reg = <0x4830a000 0x10>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
 			ti,hwmods = "epwmss5";
 			status = "disabled";
+
+			ehrpwm5: ehrpwm@4830a200 {
+				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				reg = <0x4830a200 0x80>;
+				ti,hwmods = "ehrpwm5";
+				status = "disabled";
+			};
+		};
+
+		sham: sham@53100000 {
+			compatible = "ti,omap5-sham";
+			ti,hwmods = "sham";
+			reg = <0x53100000 0x300>;
+			dmas = <&edma 36>;
+			dma-names = "rx";
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
 		aes: aes@53501000 {
@@ -417,6 +621,9 @@
 			ti,hwmods = "aes";
 			reg = <0x53501000 0xa0>;
 			interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&edma 6
+				&edma 5>;
+			dma-names = "tx", "rx";
 		};
 
 		des: des@53701000 {
@@ -424,6 +631,37 @@
 			ti,hwmods = "des";
 			reg = <0x53701000 0xa0>;
 			interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&edma 34
+				&edma 33>;
+			dma-names = "tx", "rx";
+		};
+
+		mcasp0: mcasp@48038000 {
+			compatible = "ti,am33xx-mcasp-audio";
+			ti,hwmods = "mcasp0";
+			reg = <0x48038000 0x2000>,
+			      <0x46000000 0x400000>;
+			reg-names = "mpu", "dat";
+			interrupts = <80>, <81>;
+			interrupts-names = "tx", "rx";
+			status = "disabled";
+			dmas = <&edma 8>,
+			       <&edma 9>;
+			dma-names = "tx", "rx";
+		};
+
+		mcasp1: mcasp@4803C000 {
+			compatible = "ti,am33xx-mcasp-audio";
+			ti,hwmods = "mcasp1";
+			reg = <0x4803C000 0x2000>,
+			      <0x46400000 0x400000>;
+			reg-names = "mpu", "dat";
+			interrupts = <82>, <83>;
+			interrupts-names = "tx", "rx";
+			status = "disabled";
+			dmas = <&edma 10>,
+			       <&edma 11>;
+			dma-names = "tx", "rx";
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/am43x-epos-evm.dts b/arch/arm/boot/dts/am43x-epos-evm.dts
index 74174d48f476..fbf9c4c7a94f 100644
--- a/arch/arm/boot/dts/am43x-epos-evm.dts
+++ b/arch/arm/boot/dts/am43x-epos-evm.dts
@@ -11,8 +11,176 @@
 /dts-v1/;
 
 #include "am4372.dtsi"
+#include <dt-bindings/pinctrl/am43xx.h>
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "TI AM43x EPOS EVM";
 	compatible = "ti,am43x-epos-evm","ti,am4372","ti,am43";
+
+	vmmcsd_fixed: fixedregulator-sd {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcsd_fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+	};
+
+	am43xx_pinmux: pinmux@44e10800 {
+		cpsw_default: cpsw_default {
+			pinctrl-single,pins = <
+				/* Slave 1 */
+				0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1)	/* mii1_crs.rmii1_crs */
+				0x110 (PIN_INPUT_PULLDOWN | MUX_MODE1)	/* mii1_rxerr.rmii1_rxerr */
+				0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE1)	/* mii1_txen.rmii1_txen */
+				0x118 (PIN_INPUT_PULLDOWN | MUX_MODE1)	/* mii1_rxdv.rmii1_rxdv */
+				0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE1)	/* mii1_txd1.rmii1_txd1 */
+				0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE1)	/* mii1_txd0.rmii1_txd0 */
+				0x13c (PIN_INPUT_PULLDOWN | MUX_MODE1)	/* mii1_rxd1.rmii1_rxd1 */
+				0x140 (PIN_INPUT_PULLDOWN | MUX_MODE1)	/* mii1_rxd0.rmii1_rxd0 */
+				0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* rmii1_refclk.rmii1_refclk */
+			>;
+		};
+
+		cpsw_sleep: cpsw_sleep {
+			pinctrl-single,pins = <
+				/* Slave 1 reset value */
+				0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			>;
+		};
+
+		davinci_mdio_default: davinci_mdio_default {
+			pinctrl-single,pins = <
+				/* MDIO */
+				0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)	/* mdio_data.mdio_data */
+				0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0)			/* mdio_clk.mdio_clk */
+			>;
+		};
+
+		davinci_mdio_sleep: davinci_mdio_sleep {
+			pinctrl-single,pins = <
+				/* MDIO reset value */
+				0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			>;
+		};
+
+		i2c0_pins: pinmux_i2c0_pins {
+			pinctrl-single,pins = <
+				0x188 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)	/* i2c0_sda.i2c0_sda */
+				0x18c (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)	/* i2c0_scl.i2c0_scl */
+			>;
+		};
+	};
+
+	matrix_keypad: matrix_keypad@0 {
+			compatible = "gpio-matrix-keypad";
+			debounce-delay-ms = <5>;
+			col-scan-delay-us = <2>;
+
+			row-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH		/* Bank0, pin12 */
+				     &gpio0 13 GPIO_ACTIVE_HIGH		/* Bank0, pin13 */
+				     &gpio0 14 GPIO_ACTIVE_HIGH		/* Bank0, pin14 */
+				     &gpio0 15 GPIO_ACTIVE_HIGH>;	/* Bank0, pin15 */
+
+			col-gpios = <&gpio3 9 GPIO_ACTIVE_HIGH		/* Bank3, pin9 */
+				     &gpio3 10 GPIO_ACTIVE_HIGH		/* Bank3, pin10 */
+				     &gpio2 18 GPIO_ACTIVE_HIGH		/* Bank2, pin18 */
+				     &gpio2 19 GPIO_ACTIVE_HIGH>;	/* Bank2, pin19 */
+
+			linux,keymap = <0x00000201	/* P1 */
+				0x01000204	/* P4 */
+				0x02000207	/* P7 */
+				0x0300020a	/* NUMERIC_STAR */
+				0x00010202	/* P2 */
+				0x01010205	/* P5 */
+				0x02010208	/* P8 */
+				0x03010200	/* P0 */
+				0x00020203	/* P3 */
+				0x01020206	/* P6 */
+				0x02020209	/* P9 */
+				0x0302020b	/* NUMERIC_POUND */
+				0x00030067	/* UP */
+				0x0103006a	/* RIGHT */
+				0x0203006c	/* DOWN */
+				0x03030069>;	/* LEFT */
+		};
+};
+
+&mmc1 {
+	status = "okay";
+	vmmc-supply = <&vmmcsd_fixed>;
+	bus-width = <4>;
+};
+
+&mac {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&cpsw_default>;
+	pinctrl-1 = <&cpsw_sleep>;
+	status = "okay";
+};
+
+&davinci_mdio {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&davinci_mdio_default>;
+	pinctrl-1 = <&davinci_mdio_sleep>;
+	status = "okay";
+};
+
+&cpsw_emac0 {
+	phy_id = <&davinci_mdio>, <16>;
+	phy-mode = "rmii";
+};
+
+&cpsw_emac1 {
+	phy_id = <&davinci_mdio>, <1>;
+	phy-mode = "rmii";
+};
+
+&i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+
+	at24@50 {
+		compatible = "at24,24c256";
+		pagesize = <64>;
+		reg = <0x50>;
+	};
+
+	pixcir_ts@5c {
+		compatible = "pixcir,pixcir_ts";
+		reg = <0x5c>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <17 0>;
+
+		attb-gpio = <&gpio1 17 GPIO_ACTIVE_HIGH>;
+
+		x-size = <1024>;
+		y-size = <768>;
+	};
+};
+
+&gpio0 {
+	status = "okay";
+};
+
+&gpio1 {
+	status = "okay";
+};
+
+&gpio2 {
+	status = "okay";
+};
+
+&gpio3 {
+	status = "okay";
 };
diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts
index 3abf5f41e5cc..5babba0a3a75 100644
--- a/arch/arm/boot/dts/dra7-evm.dts
+++ b/arch/arm/boot/dts/dra7-evm.dts
@@ -269,3 +269,7 @@
 	vmmc-supply = <&mmc2_3v3>;
 	bus-width = <8>;
 };
+
+&cpu0 {
+	cpu0-supply = <&smps123_reg>;
+};
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index c01ef769761f..d0df4c4e8b0a 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -20,6 +20,11 @@
 	interrupt-parent = <&gic>;
 
 	aliases {
+		i2c0 = &i2c1;
+		i2c1 = &i2c2;
+		i2c2 = &i2c3;
+		i2c3 = &i2c4;
+		i2c4 = &i2c5;
 		serial0 = &uart1;
 		serial1 = &uart2;
 		serial2 = &uart3;
@@ -32,10 +37,16 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu@0 {
+		cpu0: cpu@0 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0>;
+
+			operating-points = <
+				/* kHz    uV */
+				1000000	1060000
+				1176000	1160000
+				>;
 		};
 		cpu@1 {
 			device_type = "cpu";
diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts
index 7669c16259a5..fa532aaacc68 100644
--- a/arch/arm/boot/dts/omap3-beagle.dts
+++ b/arch/arm/boot/dts/omap3-beagle.dts
@@ -173,6 +173,8 @@
 &usb_otg_hs {
 	interface-type = <0>;
 	usb-phy = <&usb2_phy>;
+	phys = <&usb2_phy>;
+	phy-names = "usb2-phy";
 	mode = <3>;
 	power = <50>;
 };
diff --git a/arch/arm/boot/dts/omap3-gta04.dts b/arch/arm/boot/dts/omap3-gta04.dts
index a84684a95891..b9b55c95a566 100644
--- a/arch/arm/boot/dts/omap3-gta04.dts
+++ b/arch/arm/boot/dts/omap3-gta04.dts
@@ -131,6 +131,8 @@
 &usb_otg_hs {
 	interface-type = <0>;
 	usb-phy = <&usb2_phy>;
+	phys = <&usb2_phy>;
+	phy-names = "usb2-phy";
 	mode = <3>;
 	power = <50>;
 };
diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts
index d64fa04e83f6..c4f20bfe4cce 100644
--- a/arch/arm/boot/dts/omap3-n900.dts
+++ b/arch/arm/boot/dts/omap3-n900.dts
@@ -26,9 +26,116 @@
 		reg = <0x80000000 0x10000000>; /* 256 MB */
 	};
 
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		camera_lens_cover {
+			label = "Camera Lens Cover";
+			gpios = <&gpio4 14 GPIO_ACTIVE_LOW>; /* 110 */
+			linux,input-type = <5>; /* EV_SW */
+			linux,code = <0x09>; /* SW_CAMERA_LENS_COVER */
+			gpio-key,wakeup;
+		};
+
+		camera_focus {
+			label = "Camera Focus";
+			gpios = <&gpio3 4 GPIO_ACTIVE_LOW>; /* 68 */
+			linux,code = <0x210>; /* KEY_CAMERA_FOCUS */
+			gpio-key,wakeup;
+		};
+
+		camera_capture {
+			label = "Camera Capture";
+			gpios = <&gpio3 5 GPIO_ACTIVE_LOW>; /* 69 */
+			linux,code = <0xd4>; /* KEY_CAMERA */
+			gpio-key,wakeup;
+		};
+
+		lock_button {
+			label = "Lock Button";
+			gpios = <&gpio4 17 GPIO_ACTIVE_LOW>; /* 113 */
+			linux,code = <0x98>; /* KEY_SCREENLOCK */
+			gpio-key,wakeup;
+		};
+
+		keypad_slide {
+			label = "Keypad Slide";
+			gpios = <&gpio3 7 GPIO_ACTIVE_LOW>; /* 71 */
+			linux,input-type = <5>; /* EV_SW */
+			linux,code = <0x0a>; /* SW_KEYPAD_SLIDE */
+			gpio-key,wakeup;
+		};
+
+		proximity_sensor {
+			label = "Proximity Sensor";
+			gpios = <&gpio3 25 GPIO_ACTIVE_HIGH>; /* 89 */
+			linux,input-type = <5>; /* EV_SW */
+			linux,code = <0x0b>; /* SW_FRONT_PROXIMITY */
+		};
+	};
+
+};
+
+&omap3_pmx_core {
+	pinctrl-names = "default";
+
+	uart2_pins: pinmux_uart2_pins {
+		pinctrl-single,pins = <
+			0x14a (PIN_INPUT | MUX_MODE0)		/* uart2_rx */
+			0x148 (PIN_OUTPUT | MUX_MODE0)		/* uart2_tx */
+		>;
+	};
+
+	uart3_pins: pinmux_uart3_pins {
+		pinctrl-single,pins = <
+			0x16e (PIN_INPUT | MUX_MODE0)		/* uart3_rx */
+			0x170 (PIN_OUTPUT | MUX_MODE0)		/* uart3_tx */
+		>;
+	};
+
+	i2c1_pins: pinmux_i2c1_pins {
+		pinctrl-single,pins = <
+			0x18a (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_scl */
+			0x18c (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_sda */
+		>;
+	};
+
+	i2c2_pins: pinmux_i2c2_pins {
+		pinctrl-single,pins = <
+			0x18e (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c2_scl */
+			0x190 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c2_sda */
+		>;
+	};
+
+	i2c3_pins: pinmux_i2c3_pins {
+		pinctrl-single,pins = <
+			0x192 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c3_scl */
+			0x194 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c3_sda */
+		>;
+	};
+
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			0x114 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_clk */
+			0x116 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_cmd */
+			0x118 (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc1_dat0 */
+			0x11a (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_dat1 */
+			0x11c (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_dat2 */
+			0x11e (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_dat3 */
+		>;
+	};
+
+	display_pins: pinmux_display_pins {
+		pinctrl-single,pins = <
+			0x0d4 (PIN_OUTPUT | MUX_MODE4)		/* RX51_LCD_RESET_GPIO */
+		>;
+	};
 };
 
 &i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+
 	clock-frequency = <2200000>;
 
 	twl: twl@48 {
@@ -39,6 +146,98 @@
 };
 
 #include "twl4030.dtsi"
+#include "twl4030_omap3.dtsi"
+
+&vaux1 {
+	regulator-name = "V28";
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+	regulator-always-on; /* due battery cover sensor */
+};
+
+&vaux2 {
+	regulator-name = "VCSI";
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+};
+
+&vaux3 {
+	regulator-name = "VMMC2_30";
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <3000000>;
+};
+
+&vaux4 {
+	regulator-name = "VCAM_ANA_28";
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+};
+
+&vmmc1 {
+	regulator-name = "VMMC1";
+	regulator-min-microvolt = <1850000>;
+	regulator-max-microvolt = <3150000>;
+};
+
+&vmmc2 {
+	regulator-name = "V28_A";
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-always-on; /* due VIO leak to AIC34 VDDs */
+};
+
+&vpll1 {
+	regulator-name = "VPLL";
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-always-on;
+};
+
+&vpll2 {
+	regulator-name = "VSDI_CSI";
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-always-on;
+};
+
+&vsim {
+	regulator-name = "VMMC2_IO_18";
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+};
+
+&vio {
+	regulator-name = "VIO";
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+
+};
+
+&vintana1 {
+	regulator-name = "VINTANA1";
+	/* fixed to 1500000 */
+	regulator-always-on;
+};
+
+&vintana2 {
+	regulator-name = "VINTANA2";
+	regulator-min-microvolt = <2750000>;
+	regulator-max-microvolt = <2750000>;
+	regulator-always-on;
+};
+
+&vintdig {
+	regulator-name = "VINTDIG";
+	/* fixed to 1500000 */
+	regulator-always-on;
+};
+
+&twl {
+	twl_audio: audio {
+		compatible = "ti,twl4030-audio";
+		ti,enable-vibra = <1>;
+	};
+};
 
 &twl_gpio {
 	ti,pullups	= <0x0>;
@@ -46,15 +245,117 @@
 };
 
 &i2c2 {
-	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+
+	clock-frequency = <100000>;
+
+	tlv320aic3x: tlv320aic3x@18 {
+		compatible = "ti,tlv320aic3x";
+		reg = <0x18>;
+		gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */
+		ai3x-gpio-func = <
+			0 /* AIC3X_GPIO1_FUNC_DISABLED */
+			5 /* AIC3X_GPIO2_FUNC_DIGITAL_MIC_INPUT */
+		>;
+
+		AVDD-supply = <&vmmc2>;
+		DRVDD-supply = <&vmmc2>;
+		IOVDD-supply = <&vio>;
+		DVDD-supply = <&vio>;
+	};
+
+	tlv320aic3x_aux: tlv320aic3x@19 {
+		compatible = "ti,tlv320aic3x";
+		reg = <0x19>;
+		gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */
+
+		AVDD-supply = <&vmmc2>;
+		DRVDD-supply = <&vmmc2>;
+		IOVDD-supply = <&vio>;
+		DVDD-supply = <&vio>;
+	};
+
+	lp5523: lp5523@32 {
+		compatible = "national,lp5523";
+		reg = <0x32>;
+		clock-mode = /bits/ 8 <0>; /* LP55XX_CLOCK_AUTO */
+		enable-gpio = <&gpio2 9 GPIO_ACTIVE_HIGH>; /* 41 */
+
+		chan0 {
+			chan-name = "lp5523:kb1";
+			led-cur = /bits/ 8 <50>;
+			max-cur = /bits/ 8 <100>;
+		};
+
+		chan1 {
+			chan-name = "lp5523:kb2";
+			led-cur = /bits/ 8 <50>;
+			max-cur = /bits/ 8 <100>;
+		};
+
+		chan2 {
+			chan-name = "lp5523:kb3";
+			led-cur = /bits/ 8 <50>;
+			max-cur = /bits/ 8 <100>;
+		};
+
+		chan3 {
+			chan-name = "lp5523:kb4";
+			led-cur = /bits/ 8 <50>;
+			max-cur = /bits/ 8 <100>;
+		};
+
+		chan4 {
+			chan-name = "lp5523:b";
+			led-cur = /bits/ 8 <50>;
+			max-cur = /bits/ 8 <100>;
+		};
+
+		chan5 {
+			chan-name = "lp5523:g";
+			led-cur = /bits/ 8 <50>;
+			max-cur = /bits/ 8 <100>;
+		};
+
+		chan6 {
+			chan-name = "lp5523:r";
+			led-cur = /bits/ 8 <50>;
+			max-cur = /bits/ 8 <100>;
+		};
+
+		chan7 {
+			chan-name = "lp5523:kb5";
+			led-cur = /bits/ 8 <50>;
+			max-cur = /bits/ 8 <100>;
+		};
+
+		chan8 {
+			chan-name = "lp5523:kb6";
+			led-cur = /bits/ 8 <50>;
+			max-cur = /bits/ 8 <100>;
+		};
+	};
+
+	bq27200: bq27200@55 {
+		compatible = "ti,bq27200";
+		reg = <0x55>;
+	};
 };
 
 &i2c3 {
-	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3_pins>;
+
+	clock-frequency = <400000>;
 };
 
 &mmc1 {
-	status = "disabled";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	vmmc-supply = <&vmmc1>;
+	bus-width = <4>;
+	cd-gpios = <&gpio6 0 GPIO_ACTIVE_HIGH>; /* 160 */
 };
 
 &mmc2 {
@@ -65,6 +366,78 @@
 	status = "disabled";
 };
 
+&gpmc {
+	ranges = <0 0 0x04000000 0x10000000>; /* 256MB */
+
+	/* gpio-irq for dma: 65 */
+
+	onenand@0,0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0 0 0x10000000>;
+
+		gpmc,sync-read;
+		gpmc,sync-write;
+		gpmc,burst-length = <16>;
+		gpmc,burst-read;
+		gpmc,burst-wrap;
+		gpmc,burst-write;
+		gpmc,device-width = <2>; /* GPMC_DEVWIDTH_16BIT */
+		gpmc,mux-add-data = <2>; /* GPMC_MUX_AD */
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <87>;
+		gpmc,cs-wr-off-ns = <87>;
+		gpmc,adv-on-ns = <0>;
+		gpmc,adv-rd-off-ns = <10>;
+		gpmc,adv-wr-off-ns = <10>;
+		gpmc,oe-on-ns = <15>;
+		gpmc,oe-off-ns = <87>;
+		gpmc,we-on-ns = <0>;
+		gpmc,we-off-ns = <87>;
+		gpmc,rd-cycle-ns = <112>;
+		gpmc,wr-cycle-ns = <112>;
+		gpmc,access-ns = <81>;
+		gpmc,page-burst-access-ns = <15>;
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-delay-ns = <0>;
+		gpmc,wait-monitoring-ns = <0>;
+		gpmc,clk-activation-ns = <5>;
+		gpmc,wr-data-mux-bus-ns = <30>;
+		gpmc,wr-access-ns = <81>;
+		gpmc,sync-clk-ps = <15000>;
+
+		/*
+		 * MTD partition table corresponding to Nokia's
+		 * Maemo 5 (Fremantle) release.
+		 */
+		partition@0 {
+			label = "bootloader";
+			reg = <0x00000000 0x00020000>;
+			read-only;
+		};
+		partition@1 {
+			label = "config";
+			reg = <0x00020000 0x00060000>;
+		};
+		partition@2 {
+			label = "log";
+			reg = <0x00080000 0x00040000>;
+		};
+		partition@3 {
+			label = "kernel";
+			reg = <0x000c0000 0x00200000>;
+		};
+		partition@4 {
+			label = "initfs";
+			reg = <0x002c0000 0x00200000>;
+		};
+		partition@5 {
+			label = "rootfs";
+			reg = <0x004c0000 0x0fb40000>;
+		};
+	};
+};
+
 &mcspi1 {
 	/*
 	 * For some reason, touchscreen is necessary for screen to work at
@@ -81,12 +454,31 @@
 		compatible = "acx565akm";
 		spi-max-frequency = <6000000>;
 		reg = <2>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&display_pins>;
 	};
 };
 
 &usb_otg_hs {
 	interface-type = <0>;
 	usb-phy = <&usb2_phy>;
+	phys = <&usb2_phy>;
+	phy-names = "usb2-phy";
 	mode = <2>;
 	power = <50>;
 };
+
+&uart1 {
+	status = "disabled";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+};
diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi
index f275beea67b6..f3a0c26ed0c2 100644
--- a/arch/arm/boot/dts/omap3.dtsi
+++ b/arch/arm/boot/dts/omap3.dtsi
@@ -19,6 +19,9 @@
 	interrupt-parent = <&intc>;
 
 	aliases {
+		i2c0 = &i2c1;
+		i2c1 = &i2c2;
+		i2c2 = &i2c3;
 		serial0 = &uart1;
 		serial1 = &uart2;
 		serial2 = &uart3;
@@ -37,6 +40,7 @@
 
 	pmu {
 		compatible = "arm,cortex-a8-pmu";
+		reg = <0x54000000 0x800000>;
 		interrupts = <3>;
 		ti,hwmods = "debugss";
 	};
@@ -71,6 +75,8 @@
 	 */
 	ocp {
 		compatible = "simple-bus";
+		reg = <0x68000000 0x10000>;
+		interrupts = <9 10>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges;
@@ -193,24 +199,40 @@
 
 		uart1: serial@4806a000 {
 			compatible = "ti,omap3-uart";
+			reg = <0x4806a000 0x2000>;
+			interrupts = <72>;
+			dmas = <&sdma 49 &sdma 50>;
+			dma-names = "tx", "rx";
 			ti,hwmods = "uart1";
 			clock-frequency = <48000000>;
 		};
 
 		uart2: serial@4806c000 {
 			compatible = "ti,omap3-uart";
+			reg = <0x4806c000 0x400>;
+			interrupts = <73>;
+			dmas = <&sdma 51 &sdma 52>;
+			dma-names = "tx", "rx";
 			ti,hwmods = "uart2";
 			clock-frequency = <48000000>;
 		};
 
 		uart3: serial@49020000 {
 			compatible = "ti,omap3-uart";
+			reg = <0x49020000 0x400>;
+			interrupts = <74>;
+			dmas = <&sdma 53 &sdma 54>;
+			dma-names = "tx", "rx";
 			ti,hwmods = "uart3";
 			clock-frequency = <48000000>;
 		};
 
 		i2c1: i2c@48070000 {
 			compatible = "ti,omap3-i2c";
+			reg = <0x48070000 0x80>;
+			interrupts = <56>;
+			dmas = <&sdma 27 &sdma 28>;
+			dma-names = "tx", "rx";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ti,hwmods = "i2c1";
@@ -218,6 +240,10 @@
 
 		i2c2: i2c@48072000 {
 			compatible = "ti,omap3-i2c";
+			reg = <0x48072000 0x80>;
+			interrupts = <57>;
+			dmas = <&sdma 29 &sdma 30>;
+			dma-names = "tx", "rx";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ti,hwmods = "i2c2";
@@ -225,6 +251,10 @@
 
 		i2c3: i2c@48060000 {
 			compatible = "ti,omap3-i2c";
+			reg = <0x48060000 0x80>;
+			interrupts = <61>;
+			dmas = <&sdma 25 &sdma 26>;
+			dma-names = "tx", "rx";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ti,hwmods = "i2c3";
@@ -232,6 +262,8 @@
 
 		mcspi1: spi@48098000 {
 			compatible = "ti,omap2-mcspi";
+			reg = <0x48098000 0x100>;
+			interrupts = <65>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ti,hwmods = "mcspi1";
@@ -250,6 +282,8 @@
 
 		mcspi2: spi@4809a000 {
 			compatible = "ti,omap2-mcspi";
+			reg = <0x4809a000 0x100>;
+			interrupts = <66>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ti,hwmods = "mcspi2";
@@ -263,6 +297,8 @@
 
 		mcspi3: spi@480b8000 {
 			compatible = "ti,omap2-mcspi";
+			reg = <0x480b8000 0x100>;
+			interrupts = <91>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ti,hwmods = "mcspi3";
@@ -276,6 +312,8 @@
 
 		mcspi4: spi@480ba000 {
 			compatible = "ti,omap2-mcspi";
+			reg = <0x480ba000 0x100>;
+			interrupts = <48>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ti,hwmods = "mcspi4";
@@ -284,8 +322,17 @@
 			dma-names = "tx0", "rx0";
 		};
 
+		hdqw1w: 1w@480b2000 {
+			compatible = "ti,omap3-1w";
+			reg = <0x480b2000 0x1000>;
+			interrupts = <58>;
+			ti,hwmods = "hdq1w";
+		};
+
 		mmc1: mmc@4809c000 {
 			compatible = "ti,omap3-hsmmc";
+			reg = <0x4809c000 0x200>;
+			interrupts = <83>;
 			ti,hwmods = "mmc1";
 			ti,dual-volt;
 			dmas = <&sdma 61>, <&sdma 62>;
@@ -294,6 +341,8 @@
 
 		mmc2: mmc@480b4000 {
 			compatible = "ti,omap3-hsmmc";
+			reg = <0x480b4000 0x200>;
+			interrupts = <86>;
 			ti,hwmods = "mmc2";
 			dmas = <&sdma 47>, <&sdma 48>;
 			dma-names = "tx", "rx";
@@ -301,6 +350,8 @@
 
 		mmc3: mmc@480ad000 {
 			compatible = "ti,omap3-hsmmc";
+			reg = <0x480ad000 0x200>;
+			interrupts = <94>;
 			ti,hwmods = "mmc3";
 			dmas = <&sdma 77>, <&sdma 78>;
 			dma-names = "tx", "rx";
@@ -308,6 +359,7 @@
 
 		wdt2: wdt@48314000 {
 			compatible = "ti,omap3-wdt";
+			reg = <0x48314000 0x80>;
 			ti,hwmods = "wd_timer2";
 		};
 
diff --git a/arch/arm/boot/dts/omap36xx.dtsi b/arch/arm/boot/dts/omap36xx.dtsi
index f8b3765eb9be..380c22eb468e 100644
--- a/arch/arm/boot/dts/omap36xx.dtsi
+++ b/arch/arm/boot/dts/omap36xx.dtsi
@@ -31,6 +31,10 @@
 	ocp {
 		uart4: serial@49042000 {
 			compatible = "ti,omap3-uart";
+			reg = <0x49042000 0x400>;
+			interrupts = <80>;
+			dmas = <&sdma 81 &sdma 82>;
+			dma-names = "tx", "rx";
 			ti,hwmods = "uart4";
 			clock-frequency = <48000000>;
 		};
diff --git a/arch/arm/boot/dts/omap4-panda-es.dts b/arch/arm/boot/dts/omap4-panda-es.dts
index 56c435468e94..816d1c95b592 100644
--- a/arch/arm/boot/dts/omap4-panda-es.dts
+++ b/arch/arm/boot/dts/omap4-panda-es.dts
@@ -62,3 +62,7 @@
 		gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
 	};
 };
+
+&gpio1 {
+	 ti,no-reset-on-init;
+};
diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
index 17a3618b190f..e8d97b46690c 100644
--- a/arch/arm/boot/dts/omap4.dtsi
+++ b/arch/arm/boot/dts/omap4.dtsi
@@ -17,6 +17,10 @@
 	interrupt-parent = <&gic>;
 
 	aliases {
+		i2c0 = &i2c1;
+		i2c1 = &i2c2;
+		i2c2 = &i2c3;
+		i2c3 = &i2c4;
 		serial0 = &uart1;
 		serial1 = &uart2;
 		serial2 = &uart3;
@@ -218,6 +222,7 @@
 			gpmc,num-cs = <8>;
 			gpmc,num-waitpins = <4>;
 			ti,hwmods = "gpmc";
+			ti,no-idle-on-init;
 		};
 
 		uart1: serial@4806a000 {
@@ -496,6 +501,7 @@
 			reg = <0x4c000000 0x100>;
 			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "emif1";
+			ti,no-idle-on-init;
 			phy-type = <1>;
 			hw-caps-read-idle-ctrl;
 			hw-caps-ll-interface;
@@ -507,6 +513,7 @@
 			reg = <0x4d000000 0x100>;
 			interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "emif2";
+			ti,no-idle-on-init;
 			phy-type = <1>;
 			hw-caps-read-idle-ctrl;
 			hw-caps-ll-interface;
diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts
index d784b3a00410..002fa70180a5 100644
--- a/arch/arm/boot/dts/omap5-uevm.dts
+++ b/arch/arm/boot/dts/omap5-uevm.dts
@@ -62,7 +62,6 @@
 	pinctrl-0 = <
 			&twl6040_pins
 			&mcpdm_pins
-			&dmic_pins
 			&mcbsp1_pins
 			&mcbsp2_pins
 			&usbhost_pins
@@ -71,7 +70,7 @@
 
 	twl6040_pins: pinmux_twl6040_pins {
 		pinctrl-single,pins = <
-			0x18a (PIN_OUTPUT | MUX_MODE6)	/* perslimbus2_clock.gpio5_145 */
+			0x17e (PIN_OUTPUT | MUX_MODE6)	/* mcspi1_somi.gpio5_141 */
 		>;
 	};
 
@@ -85,15 +84,6 @@
 		>;
 	};
 
-	dmic_pins: pinmux_dmic_pins {
-		pinctrl-single,pins = <
-			0x144 (PIN_INPUT | MUX_MODE0)		/* abedmic_din1.abedmic_din1 */
-			0x146 (PIN_INPUT | MUX_MODE0)		/* abedmic_din2.abedmic_din2 */
-			0x148 (PIN_INPUT | MUX_MODE0)		/* abedmic_din3.abedmic_din3 */
-			0x14a (PIN_OUTPUT | MUX_MODE0)		/* abedmic_clk1.abedmic_clk1 */
-		>;
-	};
-
 	mcbsp1_pins: pinmux_mcbsp1_pins {
 		pinctrl-single,pins = <
 			0x14c (PIN_INPUT | MUX_MODE1)		/* abedmic_clk2.abemcbsp1_fsx */
@@ -131,25 +121,25 @@
 			0xbc (PIN_INPUT | MUX_MODE0)		/*  mcspi2_clk */
 			0xbe (PIN_INPUT | MUX_MODE0)		/*  mcspi2_simo */
 			0xc0 (PIN_INPUT_PULLUP | MUX_MODE0)	/*  mcspi2_somi */
-			0xc2 (PIN_OUTPUT | MUX_MODE0)		/*  mcspi2_cs */
+			0xc2 (PIN_OUTPUT | MUX_MODE0)		/*  mcspi2_cs0 */
 		>;
 	};
 
 	mcspi3_pins: pinmux_mcspi3_pins {
 		pinctrl-single,pins = <
-			0x78 (PIN_INPUT | MUX_MODE1)		/*  mcspi2_somi */
-			0x7a (PIN_INPUT | MUX_MODE1)		/*  mcspi2_cs */
-			0x7c (PIN_INPUT | MUX_MODE1)		/*  mcspi2_simo */
-			0x7e (PIN_INPUT | MUX_MODE1)		/*  mcspi2_clk */
+			0x78 (PIN_INPUT | MUX_MODE1)		/*  mcspi3_somi */
+			0x7a (PIN_INPUT | MUX_MODE1)		/*  mcspi3_cs0 */
+			0x7c (PIN_INPUT | MUX_MODE1)		/*  mcspi3_simo */
+			0x7e (PIN_INPUT | MUX_MODE1)		/*  mcspi3_clk */
 		>;
 	};
 
 	mcspi4_pins: pinmux_mcspi4_pins {
 		pinctrl-single,pins = <
-			0x164 (PIN_INPUT | MUX_MODE1)		/*  mcspi2_clk */
-			0x168 (PIN_INPUT | MUX_MODE1)		/*  mcspi2_simo */
-			0x16a (PIN_INPUT | MUX_MODE1)		/*  mcspi2_somi */
-			0x16c (PIN_INPUT | MUX_MODE1)		/*  mcspi2_cs */
+			0x164 (PIN_INPUT | MUX_MODE1)		/*  mcspi4_clk */
+			0x168 (PIN_INPUT | MUX_MODE1)		/*  mcspi4_simo */
+			0x16a (PIN_INPUT | MUX_MODE1)		/*  mcspi4_somi */
+			0x16c (PIN_INPUT | MUX_MODE1)		/*  mcspi4_cs0 */
 		>;
 	};
 
@@ -334,8 +324,6 @@
 					regulator-name = "smps10_out1";
 					regulator-min-microvolt = <5000000>;
 					regulator-max-microvolt = <5000000>;
-					regulator-always-on;
-					regulator-boot-on;
 				};
 
 				ldo1_reg: ldo1 {
@@ -503,3 +491,7 @@
         pinctrl-names = "default";
         pinctrl-0 = <&uart5_pins>;
 };
+
+&cpu0 {
+	cpu0-supply = <&smps123_reg>;
+};
diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi
index 6192c458bea1..154d92fae1d5 100644
--- a/arch/arm/boot/dts/omap5.dtsi
+++ b/arch/arm/boot/dts/omap5.dtsi
@@ -21,6 +21,11 @@
 	interrupt-parent = <&gic>;
 
 	aliases {
+		i2c0 = &i2c1;
+		i2c1 = &i2c2;
+		i2c2 = &i2c3;
+		i2c3 = &i2c4;
+		i2c4 = &i2c5;
 		serial0 = &uart1;
 		serial1 = &uart2;
 		serial2 = &uart3;
@@ -33,10 +38,17 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu@0 {
+		cpu0: cpu@0 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x0>;
+
+			operating-points = <
+				/* kHz    uV */
+				500000  880000
+				1000000 1060000
+				1500000 1250000
+			>;
 		};
 		cpu@1 {
 			device_type = "cpu";
@@ -52,7 +64,6 @@
 			     <GIC_PPI 14 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
 			     <GIC_PPI 11 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
 			     <GIC_PPI 10 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>;
-		clock-frequency = <6144000>;
 	};
 
 	gic: interrupt-controller@48211000 {
@@ -607,6 +618,7 @@
 		emif1: emif@4c000000 {
 			compatible	= "ti,emif-4d5";
 			ti,hwmods	= "emif1";
+			ti,no-idle-on-init;
 			phy-type	= <2>; /* DDR PHY type: Intelli PHY */
 			reg = <0x4c000000 0x400>;
 			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
@@ -618,6 +630,7 @@
 		emif2: emif@4d000000 {
 			compatible	= "ti,emif-4d5";
 			ti,hwmods	= "emif2";
+			ti,no-idle-on-init;
 			phy-type	= <2>; /* DDR PHY type: Intelli PHY */
 			reg = <0x4d000000 0x400>;
 			interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
@@ -648,6 +661,7 @@
 				reg = <0x4a030000 0x10000>;
 				interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
 				usb-phy = <&usb2_phy>, <&usb3_phy>;
+				dr_mode = "peripheral";
 				tx-fifo-resize;
 			};
 		};
diff --git a/arch/arm/boot/dts/twl4030.dtsi b/arch/arm/boot/dts/twl4030.dtsi
index ae6a17aed9ee..af7fa40fd216 100644
--- a/arch/arm/boot/dts/twl4030.dtsi
+++ b/arch/arm/boot/dts/twl4030.dtsi
@@ -23,6 +23,22 @@
 		compatible = "ti,twl4030-wdt";
 	};
 
+	vaux1: regulator-vaux1 {
+		compatible = "ti,twl4030-vaux1";
+	};
+
+	vaux2: regulator-vaux2 {
+		compatible = "ti,twl4030-vaux2";
+	};
+
+	vaux3: regulator-vaux3 {
+		compatible = "ti,twl4030-vaux3";
+	};
+
+	vaux4: regulator-vaux4 {
+		compatible = "ti,twl4030-vaux4";
+	};
+
 	vcc: regulator-vdd1 {
 		compatible = "ti,twl4030-vdd1";
 		regulator-min-microvolt = <600000>;
@@ -35,10 +51,20 @@
 		regulator-max-microvolt = <1800000>;
 	};
 
-	vpll2: regulator-vpll2 {
-		compatible = "ti,twl4030-vpll2";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
+	vio: regulator-vio {
+		compatible = "ti,twl4030-vio";
+	};
+
+	vintana1: regulator-vintana1 {
+		compatible = "ti,twl4030-vintana1";
+	};
+
+	vintana2: regulator-vintana2 {
+		compatible = "ti,twl4030-vintana2";
+	};
+
+	vintdig: regulator-vintdig {
+		compatible = "ti,twl4030-vintdig";
 	};
 
 	vmmc1: regulator-vmmc1 {
@@ -65,6 +91,16 @@
 		compatible = "ti,twl4030-vusb3v1";
 	};
 
+	vpll1: regulator-vpll1 {
+		compatible = "ti,twl4030-vpll1";
+	};
+
+	vpll2: regulator-vpll2 {
+		compatible = "ti,twl4030-vpll2";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
 	vsim: regulator-vsim {
 		compatible = "ti,twl4030-vsim";
 		regulator-min-microvolt = <1800000>;
@@ -97,4 +133,9 @@
 		compatible = "ti,twl4030-pwmled";
 		#pwm-cells = <2>;
 	};
+
+	twl_pwrbutton: pwrbutton {
+		compatible = "ti,twl4030-pwrbutton";
+		interrupts = <8>;
+	};
 };