Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC cleanups from Olof Johansson:
 "This is the branch where we usually queue up cleanup efforts, moving
  drivers out of the architecture directory, header file restructuring,
  etc.  Sometimes they tangle with new development so it's hard to keep
  it strictly to cleanups.

  Some of the things included in this branch are:

   * Atmel SAMA5 conversion to common clock
   * Reset framework conversion for tegra platforms
    - Some of this depends on tegra clock driver reworks that are shared
      with Mike Turquette's clk tree.
   * Tegra DMA refactoring, which are shared branches with the DMA tree.
   * Removal of some header files on exynos to prepare for
     multiplatform"

* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
  ARM: mvebu: move Armada 370/XP specific definitions to armada-370-xp.h
  ARM: mvebu: remove prototypes of non-existing functions from common.h
  ARM: mvebu: move ARMADA_XP_MAX_CPUS to armada-370-xp.h
  serial: sh-sci: Rework baud rate calculation
  serial: sh-sci: Compute overrun_bit without using baud rate algo
  serial: sh-sci: Remove unused GPIO request code
  serial: sh-sci: Move overrun_bit and error_mask fields out of pdata
  serial: sh-sci: Support resources passed through platform resources
  serial: sh-sci: Don't check IRQ in verify port operation
  serial: sh-sci: Set the UPF_FIXED_PORT flag
  serial: sh-sci: Remove duplicate interrupt check in verify port op
  serial: sh-sci: Simplify baud rate calculation algorithms
  serial: sh-sci: Remove baud rate calculation algorithm 5
  serial: sh-sci: Sort headers alphabetically
  ARM: EXYNOS: Kill exynos_pm_late_initcall()
  ARM: EXYNOS: Consolidate selection of PM_GENERIC_DOMAINS for Exynos4
  ARM: at91: switch Calao QIL-A9260 board to DT
  clk: at91: fix pmc_clk_ids data type attriubte
  PM / devfreq: use inclusion <mach/map.h> instead of <plat/map-s5p.h>
  ARM: EXYNOS: remove <mach/regs-clock.h> for exynos
  ...

1 files changed, 0 insertions, 266 deletions

diff --git a/arch/arm/mach-at91/board-qil-a9260.c b/arch/arm/mach-at91/board-qil-a9260.c
deleted file mode 100644
index aa3bc9b0f150..000000000000
--- a/arch/arm/mach-at91/board-qil-a9260.c
+++ /dev/null
@@ -1,266 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/board-qil-a9260.c
- *
- *  Copyright (C) 2005 SAN People
- *  Copyright (C) 2006 Atmel
- *  Copyright (C) 2007 Calao-systems
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/gpio_keys.h>
-#include <linux/input.h>
-#include <linux/clk.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/hardware.h>
-#include <mach/at91sam9_smc.h>
-
-#include "at91_aic.h"
-#include "at91_shdwc.h"
-#include "board.h"
-#include "sam9_smc.h"
-#include "generic.h"
-
-
-static void __init ek_init_early(void)
-{
-	/* Initialize processor: 12.000 MHz crystal */
-	at91_initialize(12000000);
-}
-
-/*
- * USB Host port
- */
-static struct at91_usbh_data __initdata ek_usbh_data = {
-	.ports		= 2,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-/*
- * USB Device port
- */
-static struct at91_udc_data __initdata ek_udc_data = {
-	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
-};
-
-/*
- * SPI devices.
- */
-static struct spi_board_info ek_spi_devices[] = {
-#if defined(CONFIG_RTC_DRV_M41T94)
-	{	/* M41T94 RTC */
-		.modalias	= "m41t94",
-		.chip_select	= 0,
-		.max_speed_hz	= 1 * 1000 * 1000,
-		.bus_num	= 0,
-	}
-#endif
-};
-
-/*
- * MACB Ethernet device
- */
-static struct macb_platform_data __initdata ek_macb_data = {
-	.phy_irq_pin	= AT91_PIN_PA31,
-	.is_rmii	= 1,
-};
-
-/*
- * NAND flash
- */
-static struct mtd_partition __initdata ek_nand_partition[] = {
-	{
-		.name	= "Uboot & Kernel",
-		.offset	= 0,
-		.size	= SZ_16M,
-	},
-	{
-		.name	= "Root FS",
-		.offset	= MTDPART_OFS_NXTBLK,
-		.size	= 120 * SZ_1M,
-	},
-	{
-		.name	= "FS",
-		.offset	= MTDPART_OFS_NXTBLK,
-		.size	= 120 * SZ_1M,
-	},
-};
-
-static struct atmel_nand_data __initdata ek_nand_data = {
-	.ale		= 21,
-	.cle		= 22,
-	.det_pin	= -EINVAL,
-	.rdy_pin	= AT91_PIN_PC13,
-	.enable_pin	= AT91_PIN_PC14,
-	.ecc_mode	= NAND_ECC_SOFT,
-	.on_flash_bbt	= 1,
-	.parts		= ek_nand_partition,
-	.num_parts	= ARRAY_SIZE(ek_nand_partition),
-};
-
-static struct sam9_smc_config __initdata ek_nand_smc_config = {
-	.ncs_read_setup		= 0,
-	.nrd_setup		= 1,
-	.ncs_write_setup	= 0,
-	.nwe_setup		= 1,
-
-	.ncs_read_pulse		= 3,
-	.nrd_pulse		= 3,
-	.ncs_write_pulse	= 3,
-	.nwe_pulse		= 3,
-
-	.read_cycle		= 5,
-	.write_cycle		= 5,
-
-	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
-	.tdf_cycles		= 2,
-};
-
-static void __init ek_add_device_nand(void)
-{
-	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(0, 3, &ek_nand_smc_config);
-
-	at91_add_device_nand(&ek_nand_data);
-}
-
-/*
- * MCI (SD/MMC)
- */
-static struct mci_platform_data __initdata ek_mci0_data = {
-	.slot[0] = {
-		.bus_width	= 4,
-		.detect_pin	= -EINVAL,
-		.wp_pin		= -EINVAL,
-	},
-};
-
-/*
- * GPIO Buttons
- */
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
-static struct gpio_keys_button ek_buttons[] = {
-	{	/* USER PUSH BUTTON */
-		.code		= KEY_ENTER,
-		.gpio		= AT91_PIN_PB10,
-		.active_low	= 1,
-		.desc		= "user_pb",
-		.wakeup		= 1,
-	}
-};
-
-static struct gpio_keys_platform_data ek_button_data = {
-	.buttons	= ek_buttons,
-	.nbuttons	= ARRAY_SIZE(ek_buttons),
-};
-
-static struct platform_device ek_button_device = {
-	.name		= "gpio-keys",
-	.id		= -1,
-	.num_resources	= 0,
-	.dev		= {
-		.platform_data	= &ek_button_data,
-	}
-};
-
-static void __init ek_add_device_buttons(void)
-{
-	at91_set_GPIO_periph(AT91_PIN_PB10, 1);	/* user push button, pull up enabled */
-	at91_set_deglitch(AT91_PIN_PB10, 1);
-
-	platform_device_register(&ek_button_device);
-}
-#else
-static void __init ek_add_device_buttons(void) {}
-#endif
-
-/*
- * LEDs
- */
-static struct gpio_led ek_leds[] = {
-	{	/* user_led (green) */
-		.name			= "user_led",
-		.gpio			= AT91_PIN_PB21,
-		.active_low		= 0,
-		.default_trigger	= "heartbeat",
-	}
-};
-
-static void __init ek_board_init(void)
-{
-	/* Serial */
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
-
-	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* USART2 on ttyS3. (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | ATMEL_UART_RTS);
-	at91_add_device_serial();
-	/* USB Host */
-	at91_add_device_usbh(&ek_usbh_data);
-	/* USB Device */
-	at91_add_device_udc(&ek_udc_data);
-	/* SPI */
-	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
-	/* NAND */
-	ek_add_device_nand();
-	/* I2C */
-	at91_add_device_i2c(NULL, 0);
-	/* Ethernet */
-	at91_add_device_eth(&ek_macb_data);
-	/* MMC */
-	at91_add_device_mci(0, &ek_mci0_data);
-	/* Push Buttons */
-	ek_add_device_buttons();
-	/* LEDs */
-	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
-	/* shutdown controller, wakeup button (5 msec low) */
-	at91_shdwc_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW
-				| AT91_SHDW_RTTWKEN);
-}
-
-MACHINE_START(QIL_A9260, "CALAO QIL_A9260")
-	/* Maintainer: calao-systems */
-	.init_time	= at91sam926x_pit_init,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= ek_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= ek_board_init,
-MACHINE_END