Merge tag 'u300-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/soc

From Linus Walleij:

Device Tree and Multiplatform support for U300:
- Add devicetree support to timer, pinctrl (probe), I2C block,
  watchdog, DMA controller and clocks.
- Piecewise add a device tree containing all peripherals.
- Delete the ATAG boot path.
- Delete redundant platform data and board files.
- Convert to multiplatform.

* tag 'u300-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (40 commits)
  ARM: u300: switch to using syscon regmap for board
  ARM: u300: Update MMC configs for u300 defconfig
  spi: pl022: use DMA by default when probing from DT
  pinctrl: get rid of all platform data for coh901
  ARM: u300: convert MMC/SD clock to device tree
  ARM: u300: move the gated system controller clocks to DT
  i2c: stu300: do not request a specific clock name
  clk: move the U300 fixed and fixed-factor to DT
  ARM: u300: remove register definition file
  ARM: u300: add syscon node
  ARM: u300 use module_spi_driver to register driver
  ARM: u300: delete remnant machine headers
  ARM: u300: convert to multiplatform
  ARM: u300: localize <mach/u300-regs.h>
  ARM: u300: delete <mach/irqs.h>
  ARM: u300: delete <mach/hardware.h>
  ARM: u300: push down syscon registers
  ARM: u300: remove deps from debug macro
  ARM: u300: move debugmacro to debug includes
  ARM: u300: delete all static board data
  ...

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

1 files changed, 0 insertions, 102 deletions

diff --git a/arch/arm/mach-u300/spi.c b/arch/arm/mach-u300/spi.c
deleted file mode 100644
index 910698293d64..000000000000
--- a/arch/arm/mach-u300/spi.c
+++ /dev/null
@@ -1,102 +0,0 @@
-/*
- * arch/arm/mach-u300/spi.c
- *
- * Copyright (C) 2009 ST-Ericsson AB
- * License terms: GNU General Public License (GPL) version 2
- *
- * Author: Linus Walleij <linus.walleij@stericsson.com>
- */
-#include <linux/device.h>
-#include <linux/amba/bus.h>
-#include <linux/spi/spi.h>
-#include <linux/amba/pl022.h>
-#include <linux/platform_data/dma-coh901318.h>
-#include <linux/err.h>
-
-/*
- * The following is for the actual devices on the SSP/SPI bus
- */
-#ifdef CONFIG_MACH_U300_SPIDUMMY
-static void select_dummy_chip(u32 chipselect)
-{
-	pr_debug("CORE: %s called with CS=0x%x (%s)\n",
-		 __func__,
-		 chipselect,
-		 chipselect ? "unselect chip" : "select chip");
-	/*
-	 * Here you would write the chip select value to the GPIO pins if
-	 * this was a real chip (but this is a loopback dummy).
-	 */
-}
-
-struct pl022_config_chip dummy_chip_info = {
-	/* available POLLING_TRANSFER, INTERRUPT_TRANSFER, DMA_TRANSFER */
-	.com_mode = DMA_TRANSFER,
-	.iface = SSP_INTERFACE_MOTOROLA_SPI,
-	/* We can only act as master but SSP_SLAVE is possible in theory */
-	.hierarchy = SSP_MASTER,
-	/* 0 = drive TX even as slave, 1 = do not drive TX as slave */
-	.slave_tx_disable = 0,
-	.rx_lev_trig = SSP_RX_4_OR_MORE_ELEM,
-	.tx_lev_trig = SSP_TX_4_OR_MORE_EMPTY_LOC,
-	.ctrl_len = SSP_BITS_12,
-	.wait_state = SSP_MWIRE_WAIT_ZERO,
-	.duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX,
-	/*
-	 * This is where you insert a call to a function to enable CS
-	 * (usually GPIO) for a certain chip.
-	 */
-	.cs_control = select_dummy_chip,
-};
-#endif
-
-static struct spi_board_info u300_spi_devices[] = {
-#ifdef CONFIG_MACH_U300_SPIDUMMY
-	{
-		/* A dummy chip used for loopback tests */
-		.modalias       = "spi-dummy",
-		/* Really dummy, pass in additional chip config here */
-		.platform_data  = NULL,
-		/* This defines how the controller shall handle the device */
-		.controller_data = &dummy_chip_info,
-		/* .irq - no external IRQ routed from this device */
-		.max_speed_hz   = 1000000,
-		.bus_num        = 0, /* Only one bus on this chip */
-		.chip_select    = 0,
-		/* Means SPI_CS_HIGH, change if e.g low CS */
-		.mode           = SPI_MODE_1 | SPI_LOOP,
-	},
-#endif
-};
-
-static struct pl022_ssp_controller ssp_platform_data = {
-	/* If you have several SPI buses this varies, we have only bus 0 */
-	.bus_id = 0,
-	/*
-	 * On the APP CPU GPIO 4, 5 and 6 are connected as generic
-	 * chip selects for SPI. (Same on U330, U335 and U365.)
-	 * TODO: make sure the GPIO driver can select these properly
-	 * and do padmuxing accordingly too.
-	 */
-	.num_chipselect = 3,
-#ifdef CONFIG_COH901318
-	.enable_dma = 1,
-	.dma_filter = coh901318_filter_id,
-	.dma_rx_param = (void *) U300_DMA_SPI_RX,
-	.dma_tx_param = (void *) U300_DMA_SPI_TX,
-#else
-	.enable_dma = 0,
-#endif
-};
-
-
-void __init u300_spi_init(struct amba_device *adev)
-{
-	adev->dev.platform_data = &ssp_platform_data;
-}
-
-void __init u300_spi_register_board_devices(void)
-{
-	/* Register any SPI devices */
-	spi_register_board_info(u300_spi_devices, ARRAY_SIZE(u300_spi_devices));
-}