[POWERPC] Remove APUS support from arch/ppc

Current status of APUS:
- arch/powerpc/: removed in 2.6.23
- arch/ppc/: marked BROKEN since 2 years

This therefore removes the remaining parts of APUS support from
arch/ppc, include/asm-ppc, arch/powerpc and include/asm-powerpc.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>

1 files changed, 4 insertions, 113 deletions

diff --git a/arch/ppc/kernel/head.S b/arch/ppc/kernel/head.S
index c7cb9d5f24a3..1b0ec7202dd5 100644
--- a/arch/ppc/kernel/head.S
+++ b/arch/ppc/kernel/head.S
@@ -32,10 +32,6 @@
 #include <asm/ppc_asm.h>
 #include <asm/asm-offsets.h>
 
-#ifdef CONFIG_APUS
-#include <asm/amigappc.h>
-#endif
-
 /* 601 only have IBAT; cr0.eq is set on 601 when using this macro */
 #define LOAD_BAT(n, reg, RA, RB)	\
 	/* see the comment for clear_bats() -- Cort */ \
@@ -128,14 +124,6 @@ __start:
  */
 	bl	early_init
 
-#ifdef CONFIG_APUS
-/* On APUS the __va/__pa constants need to be set to the correct
- * values before continuing.
- */
-	mr	r4,r30
-	bl	fix_mem_constants
-#endif /* CONFIG_APUS */
-
 /* Switch MMU off, clear BATs and flush TLB. At this point, r3 contains
  * the physical address we are running at, returned by early_init()
  */
@@ -145,7 +133,7 @@ __after_mmu_off:
 	bl	flush_tlbs
 
 	bl	initial_bats
-#if !defined(CONFIG_APUS) && defined(CONFIG_BOOTX_TEXT)
+#ifdef CONFIG_BOOTX_TEXT
 	bl	setup_disp_bat
 #endif
 
@@ -161,7 +149,6 @@ __after_mmu_off:
 #endif /* CONFIG_6xx */
 
 
-#ifndef CONFIG_APUS
 /*
  * We need to run with _start at physical address 0.
  * If the MMU is already turned on, we copy stuff to KERNELBASE,
@@ -172,7 +159,7 @@ __after_mmu_off:
 	addis	r4,r3,KERNELBASE@h	/* current address of _start */
 	cmpwi	0,r4,0			/* are we already running at 0? */
 	bne	relocate_kernel
-#endif /* CONFIG_APUS */
+
 /*
  * we now have the 1st 16M of ram mapped with the bats.
  * prep needs the mmu to be turned on here, but pmac already has it on.
@@ -812,85 +799,6 @@ copy_and_flush:
 	addi	r6,r6,4
 	blr
 
-#ifdef CONFIG_APUS
-/*
- * On APUS the physical base address of the kernel is not known at compile
- * time, which means the __pa/__va constants used are incorrect. In the
- * __init section is recorded the virtual addresses of instructions using
- * these constants, so all that has to be done is fix these before
- * continuing the kernel boot.
- *
- * r4 = The physical address of the kernel base.
- */
-fix_mem_constants:
-	mr	r10,r4
-	addis	r10,r10,-KERNELBASE@h    /* virt_to_phys constant */
-	neg	r11,r10	                 /* phys_to_virt constant */
-
-	lis	r12,__vtop_table_begin@h
-	ori	r12,r12,__vtop_table_begin@l
-	add	r12,r12,r10	         /* table begin phys address */
-	lis	r13,__vtop_table_end@h
-	ori	r13,r13,__vtop_table_end@l
-	add	r13,r13,r10	         /* table end phys address */
-	subi	r12,r12,4
-	subi	r13,r13,4
-1:	lwzu	r14,4(r12)               /* virt address of instruction */
-	add     r14,r14,r10              /* phys address of instruction */
-	lwz     r15,0(r14)               /* instruction, now insert top */
-	rlwimi  r15,r10,16,16,31         /* half of vp const in low half */
-	stw	r15,0(r14)               /* of instruction and restore. */
-	dcbst	r0,r14			 /* write it to memory */
-	sync
-	icbi	r0,r14			 /* flush the icache line */
-	cmpw	r12,r13
-	bne     1b
-	sync				/* additional sync needed on g4 */
-	isync
-
-/*
- * Map the memory where the exception handlers will
- * be copied to when hash constants have been patched.
- */
-#ifdef CONFIG_APUS_FAST_EXCEPT
-	lis	r8,0xfff0
-#else
-	lis	r8,0
-#endif
-	ori	r8,r8,0x2		/* 128KB, supervisor */
-	mtspr	SPRN_DBAT3U,r8
-	mtspr	SPRN_DBAT3L,r8
-
-	lis	r12,__ptov_table_begin@h
-	ori	r12,r12,__ptov_table_begin@l
-	add	r12,r12,r10	         /* table begin phys address */
-	lis	r13,__ptov_table_end@h
-	ori	r13,r13,__ptov_table_end@l
-	add	r13,r13,r10	         /* table end phys address */
-	subi	r12,r12,4
-	subi	r13,r13,4
-1:	lwzu	r14,4(r12)               /* virt address of instruction */
-	add     r14,r14,r10              /* phys address of instruction */
-	lwz     r15,0(r14)               /* instruction, now insert top */
-	rlwimi  r15,r11,16,16,31         /* half of pv const in low half*/
-	stw	r15,0(r14)               /* of instruction and restore. */
-	dcbst	r0,r14			 /* write it to memory */
-	sync
-	icbi	r0,r14			 /* flush the icache line */
-	cmpw	r12,r13
-	bne     1b
-
-	sync				/* additional sync needed on g4 */
-	isync				/* No speculative loading until now */
-	blr
-
-/***********************************************************************
- *  Please note that on APUS the exception handlers are located at the
- *  physical address 0xfff0000. For this reason, the exception handlers
- *  cannot use relative branches to access the code below.
- ***********************************************************************/
-#endif /* CONFIG_APUS */
-
 #ifdef CONFIG_SMP
 	.globl	__secondary_start_pmac_0
 __secondary_start_pmac_0:
@@ -1043,19 +951,6 @@ start_here:
 	bl	machine_init
 	bl	MMU_init
 
-#ifdef CONFIG_APUS
-	/* Copy exception code to exception vector base on APUS. */
-	lis	r4,KERNELBASE@h
-#ifdef CONFIG_APUS_FAST_EXCEPT
-	lis	r3,0xfff0		/* Copy to 0xfff00000 */
-#else
-	lis	r3,0			/* Copy to 0x00000000 */
-#endif
-	li	r5,0x4000		/* # bytes of memory to copy */
-	li	r6,0
-	bl	copy_and_flush		/* copy the first 0x4000 bytes */
-#endif  /* CONFIG_APUS */
-
 /*
  * Go back to running unmapped so we can load up new values
  * for SDR1 (hash table pointer) and the segment registers
@@ -1232,11 +1127,7 @@ initial_bats:
 #else
 	ori	r8,r8,2			/* R/W access */
 #endif /* CONFIG_SMP */
-#ifdef CONFIG_APUS
-	ori	r11,r11,BL_8M<<2|0x2	/* set up 8MB BAT registers for 604 */
-#else
 	ori	r11,r11,BL_256M<<2|0x2	/* set up BAT registers for 604 */
-#endif /* CONFIG_APUS */
 
 	mtspr	SPRN_DBAT0L,r8		/* N.B. 6xx (not 601) have valid */
 	mtspr	SPRN_DBAT0U,r11		/* bit in upper BAT register */
@@ -1245,7 +1136,7 @@ initial_bats:
 	isync
 	blr
 
-#if !defined(CONFIG_APUS) && defined(CONFIG_BOOTX_TEXT)
+#ifdef CONFIG_BOOTX_TEXT
 setup_disp_bat:
 	/*
 	 * setup the display bat prepared for us in prom.c
@@ -1268,7 +1159,7 @@ setup_disp_bat:
 	mtspr	SPRN_IBAT3U,r11
 	blr
 
-#endif /* !defined(CONFIG_APUS) && defined(CONFIG_BOOTX_TEXT) */
+#endif /* defined(CONFIG_BOOTX_TEXT) */
 
 #ifdef CONFIG_8260
 /* Jump into the system reset for the rom.