Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 302 insertions, 0 deletions

diff --git a/arch/ppc/syslib/harrier.c b/arch/ppc/syslib/harrier.c
new file mode 100644
index 000000000000..a6b3f8645793
--- /dev/null
+++ b/arch/ppc/syslib/harrier.c
@@ -0,0 +1,302 @@
+/*
+ * arch/ppc/syslib/harrier.c
+ *
+ * Motorola MCG Harrier northbridge/memory controller support
+ *
+ * Author: Dale Farnsworth
+ *         dale.farnsworth@mvista.com
+ *
+ * 2001 (c) MontaVista, Software, Inc.  This file is licensed under
+ * the terms of the GNU General Public License version 2.  This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/pci.h>
+#include <linux/harrier_defs.h>
+
+#include <asm/byteorder.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/pci.h>
+#include <asm/pci-bridge.h>
+#include <asm/open_pic.h>
+#include <asm/harrier.h>
+
+/* define defaults for inbound windows */
+#define HARRIER_ITAT_DEFAULT		(HARRIER_ITAT_ENA | \
+					 HARRIER_ITAT_MEM | \
+					 HARRIER_ITAT_WPE | \
+					 HARRIER_ITAT_GBL)
+
+#define HARRIER_MPAT_DEFAULT		(HARRIER_ITAT_ENA | \
+					 HARRIER_ITAT_MEM | \
+					 HARRIER_ITAT_WPE | \
+					 HARRIER_ITAT_GBL)
+
+/*
+ * Initialize the inbound window size on a non-monarch harrier.
+ */
+void __init harrier_setup_nonmonarch(uint ppc_reg_base, uint in0_size)
+{
+	u16 temps;
+	u32 temp;
+
+	if (in0_size > HARRIER_ITSZ_2GB) {
+		printk
+		    ("harrier_setup_nonmonarch: Invalid window size code %d\n",
+		     in0_size);
+		return;
+	}
+
+	/* Clear the PCI memory enable bit. If we don't, then when the
+	 * inbound windows are enabled below, the corresponding BARs will be
+	 * "live" and start answering to PCI memory reads from their default
+	 * addresses (0x0), which overlap with system RAM.
+	 */
+	temps = in_le16((u16 *) (ppc_reg_base +
+				 HARRIER_XCSR_CONFIG(PCI_COMMAND)));
+	temps &= ~(PCI_COMMAND_MEMORY);
+	out_le16((u16 *) (ppc_reg_base + HARRIER_XCSR_CONFIG(PCI_COMMAND)),
+		 temps);
+
+	/* Setup a non-prefetchable inbound window */
+	out_le32((u32 *) (ppc_reg_base +
+			  HARRIER_XCSR_CONFIG(HARRIER_ITSZ0_OFF)), in0_size);
+
+	temp = in_le32((u32 *) (ppc_reg_base +
+				HARRIER_XCSR_CONFIG(HARRIER_ITAT0_OFF)));
+	temp &= ~HARRIER_ITAT_PRE;
+	temp |= HARRIER_ITAT_DEFAULT;
+	out_le32((u32 *) (ppc_reg_base +
+			  HARRIER_XCSR_CONFIG(HARRIER_ITAT0_OFF)), temp);
+
+	/* Enable the message passing block */
+	temp = in_le32((u32 *) (ppc_reg_base +
+				HARRIER_XCSR_CONFIG(HARRIER_MPAT_OFF)));
+	temp |= HARRIER_MPAT_DEFAULT;
+	out_le32((u32 *) (ppc_reg_base +
+			  HARRIER_XCSR_CONFIG(HARRIER_MPAT_OFF)), temp);
+}
+
+void __init harrier_release_eready(uint ppc_reg_base)
+{
+	ulong temp;
+
+	/*
+	 * Set EREADY to allow the line to be pulled up after everyone is
+	 * ready.
+	 */
+	temp = in_be32((uint *) (ppc_reg_base + HARRIER_MISC_CSR_OFF));
+	temp |= HARRIER_EREADY;
+	out_be32((uint *) (ppc_reg_base + HARRIER_MISC_CSR_OFF), temp);
+}
+
+void __init harrier_wait_eready(uint ppc_reg_base)
+{
+	ulong temp;
+
+	/*
+	 * Poll the ERDYS line until it goes high to indicate that all
+	 * non-monarch PrPMCs are ready for bus enumeration (or that there are
+	 * no PrPMCs present).
+	 */
+
+	/* FIXME: Add a timeout of some kind to prevent endless waits. */
+	do {
+
+		temp = in_be32((uint *) (ppc_reg_base + HARRIER_MISC_CSR_OFF));
+
+	} while (!(temp & HARRIER_ERDYS));
+}
+
+/*
+ * Initialize the Motorola MCG Harrier host bridge.
+ *
+ * This means setting up the PPC bus to PCI memory and I/O space mappings,
+ * setting the PCI memory space address of the MPIC (mapped straight
+ * through), and ioremap'ing the mpic registers.
+ * 'OpenPIC_Addr' will be set correctly by this routine.
+ * This routine will not change the PCI_CONFIG_ADDR or PCI_CONFIG_DATA
+ * addresses and assumes that the mapping of PCI memory space back to system
+ * memory is set up correctly by PPCBug.
+ */
+int __init
+harrier_init(struct pci_controller *hose,
+	     uint ppc_reg_base,
+	     ulong processor_pci_mem_start,
+	     ulong processor_pci_mem_end,
+	     ulong processor_pci_io_start,
+	     ulong processor_pci_io_end, ulong processor_mpic_base)
+{
+	uint addr, offset;
+
+	/*
+	 * Some sanity checks...
+	 */
+	if (((processor_pci_mem_start & 0xffff0000) != processor_pci_mem_start)
+	    || ((processor_pci_io_start & 0xffff0000) !=
+		processor_pci_io_start)) {
+		printk("harrier_init: %s\n",
+		       "PPC to PCI mappings must start on 64 KB boundaries");
+		return -1;
+	}
+
+	if (((processor_pci_mem_end & 0x0000ffff) != 0x0000ffff) ||
+	    ((processor_pci_io_end & 0x0000ffff) != 0x0000ffff)) {
+		printk("harrier_init: PPC to PCI mappings %s\n",
+		       "must end just before a 64 KB boundaries");
+		return -1;
+	}
+
+	if (((processor_pci_mem_end - processor_pci_mem_start) !=
+	     (hose->mem_space.end - hose->mem_space.start)) ||
+	    ((processor_pci_io_end - processor_pci_io_start) !=
+	     (hose->io_space.end - hose->io_space.start))) {
+		printk("harrier_init: %s\n",
+		       "PPC and PCI memory or I/O space sizes don't match");
+		return -1;
+	}
+
+	if ((processor_mpic_base & 0xfffc0000) != processor_mpic_base) {
+		printk("harrier_init: %s\n",
+		       "MPIC address must start on 256 KB boundary");
+		return -1;
+	}
+
+	if ((pci_dram_offset & 0xffff0000) != pci_dram_offset) {
+		printk("harrier_init: %s\n",
+		       "pci_dram_offset must be multiple of 64 KB");
+		return -1;
+	}
+
+	/*
+	 * Program the OTAD/OTOF registers to set up the PCI Mem & I/O
+	 * space mappings.  These are the mappings going from the processor to
+	 * the PCI bus.
+	 *
+	 * Note: Don't need to 'AND' start/end addresses with 0xffff0000
+	 *       because sanity check above ensures that they are properly
+	 *       aligned.
+	 */
+
+	/* Set up PPC->PCI Mem mapping */
+	addr = processor_pci_mem_start | (processor_pci_mem_end >> 16);
+#ifdef CONFIG_HARRIER_STORE_GATHERING
+	offset = (hose->mem_space.start - processor_pci_mem_start) | 0x9a;
+#else
+	offset = (hose->mem_space.start - processor_pci_mem_start) | 0x92;
+#endif
+	out_be32((uint *) (ppc_reg_base + HARRIER_OTAD0_OFF), addr);
+	out_be32((uint *) (ppc_reg_base + HARRIER_OTOF0_OFF), offset);
+
+	/* Set up PPC->PCI I/O mapping -- Contiguous I/O space */
+	addr = processor_pci_io_start | (processor_pci_io_end >> 16);
+	offset = (hose->io_space.start - processor_pci_io_start) | 0x80;
+	out_be32((uint *) (ppc_reg_base + HARRIER_OTAD1_OFF), addr);
+	out_be32((uint *) (ppc_reg_base + HARRIER_OTOF1_OFF), offset);
+
+	/* Enable MPIC */
+	OpenPIC_Addr = (void *)processor_mpic_base;
+	addr = (processor_mpic_base >> 16) | 1;
+	out_be16((ushort *) (ppc_reg_base + HARRIER_MBAR_OFF), addr);
+	out_8((u_char *) (ppc_reg_base + HARRIER_MPIC_CSR_OFF),
+	      HARRIER_MPIC_OPI_ENABLE);
+
+	return 0;
+}
+
+/*
+ * Find the amount of RAM present.
+ * This assumes that PPCBug has initialized the memory controller (SMC)
+ * on the Harrier correctly (i.e., it does no sanity checking).
+ * It also assumes that the memory base registers are set to configure the
+ * memory as contigous starting with "RAM A BASE", "RAM B BASE", etc.
+ * however, RAM base registers can be skipped (e.g. A, B, C are set,
+ * D is skipped but E is set is okay).
+ */
+#define	MB	(1024*1024UL)
+
+static uint harrier_size_table[] __initdata = {
+	0 * MB,			/* 0 ==>    0 MB */
+	32 * MB,		/* 1 ==>   32 MB */
+	64 * MB,		/* 2 ==>   64 MB */
+	64 * MB,		/* 3 ==>   64 MB */
+	128 * MB,		/* 4 ==>  128 MB */
+	128 * MB,		/* 5 ==>  128 MB */
+	128 * MB,		/* 6 ==>  128 MB */
+	256 * MB,		/* 7 ==>  256 MB */
+	256 * MB,		/* 8 ==>  256 MB */
+	256 * MB,		/* 9 ==>  256 MB */
+	512 * MB,		/* a ==>  512 MB */
+	512 * MB,		/* b ==>  512 MB */
+	512 * MB,		/* c ==>  512 MB */
+	1024 * MB,		/* d ==> 1024 MB */
+	1024 * MB,		/* e ==> 1024 MB */
+	2048 * MB,		/* f ==> 2048 MB */
+};
+
+/*
+ * *** WARNING: You MUST have a BAT set up to map in the XCSR regs ***
+ *
+ * Read the memory controller's registers to determine the amount of system
+ * memory.  Assumes that the memory controller registers are already mapped
+ * into virtual memory--too early to use ioremap().
+ */
+unsigned long __init harrier_get_mem_size(uint xcsr_base)
+{
+	ulong last_addr;
+	int i;
+	uint vend_dev_id;
+	uint *size_table;
+	uint val;
+	uint *csrp;
+	uint size;
+	int size_table_entries;
+
+	vend_dev_id = in_be32((uint *) xcsr_base + PCI_VENDOR_ID);
+
+	if (((vend_dev_id & 0xffff0000) >> 16) != PCI_VENDOR_ID_MOTOROLA) {
+		printk("harrier_get_mem_size: %s (0x%x)\n",
+		       "Not a Motorola Memory Controller", vend_dev_id);
+		return 0;
+	}
+
+	vend_dev_id &= 0x0000ffff;
+
+	if (vend_dev_id == PCI_DEVICE_ID_MOTOROLA_HARRIER) {
+		size_table = harrier_size_table;
+		size_table_entries = sizeof(harrier_size_table) /
+		    sizeof(harrier_size_table[0]);
+	} else {
+		printk("harrier_get_mem_size: %s (0x%x)\n",
+		       "Not a Harrier", vend_dev_id);
+		return 0;
+	}
+
+	last_addr = 0;
+
+	csrp = (uint *) (xcsr_base + HARRIER_SDBA_OFF);
+	for (i = 0; i < 8; i++) {
+		val = in_be32(csrp++);
+
+		if (val & 0x100) {	/* If enabled */
+			size = val >> HARRIER_SDB_SIZE_SHIFT;
+			size &= HARRIER_SDB_SIZE_MASK;
+			if (size >= size_table_entries) {
+				break;	/* Register not set correctly */
+			}
+			size = size_table[size];
+
+			val &= ~(size - 1);
+			val += size;
+
+			if (val > last_addr) {
+				last_addr = val;
+			}
+		}
+	}
+
+	return last_addr;
+}