Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

Pull ACPI and power management updates from Rafael Wysocki:
 "This time we have some more new material than we used to have during
  the last couple of development cycles.

  The most important part of it to me is the introduction of a unified
  interface for accessing device properties provided by platform
  firmware.  It works with Device Trees and ACPI in a uniform way and
  drivers using it need not worry about where the properties come from
  as long as the platform firmware (either DT or ACPI) makes them
  available.  It covers both devices and "bare" device node objects
  without struct device representation as that turns out to be necessary
  in some cases.  This has been in the works for quite a few months (and
  development cycles) and has been approved by all of the relevant
  maintainers.

  On top of that, some drivers are switched over to the new interface
  (at25, leds-gpio, gpio_keys_polled) and some additional changes are
  made to the core GPIO subsystem to allow device drivers to manipulate
  GPIOs in the "canonical" way on platforms that provide GPIO
  information in their ACPI tables, but don't assign names to GPIO lines
  (in which case the driver needs to do that on the basis of what it
  knows about the device in question).  That also has been approved by
  the GPIO core maintainers and the rfkill driver is now going to use
  it.

  Second is support for hardware P-states in the intel_pstate driver.
  It uses CPUID to detect whether or not the feature is supported by the
  processor in which case it will be enabled by default.  However, it
  can be disabled entirely from the kernel command line if necessary.

  Next is support for a platform firmware interface based on ACPI
  operation regions used by the PMIC (Power Management Integrated
  Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
  That interface is used for manipulating power resources and for
  thermal management: sensor temperature reporting, trip point setting
  and so on.

  Also the ACPI core is now going to support the _DEP configuration
  information in a limited way.  Basically, _DEP it supposed to reflect
  off-the-hierarchy dependencies between devices which may be very
  indirect, like when AML for one device accesses locations in an
  operation region handled by another device's driver (usually, the
  device depended on this way is a serial bus or GPIO controller).  The
  support added this time is sufficient to make the ACPI battery driver
  work on Asus T100A, but it is general enough to be able to cover some
  other use cases in the future.

  Finally, we have a new cpufreq driver for the Loongson1B processor.

  In addition to the above, there are fixes and cleanups all over the
  place as usual and a traditional ACPICA update to a recent upstream
  release.

  As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
  Intel platforms should be able to handle power management of the DMA
  engine correctly, the cpufreq-dt driver should interact with the
  thermal subsystem in a better way and the ACPI backlight driver should
  handle some more corner cases, among other things.

  On top of the ACPICA update there are fixes for race conditions in the
  ACPICA's interrupt handling code which might lead to some random and
  strange looking failures on some systems.

  In the cleanups department the most visible part is the series of
  commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
  option.  That was triggered by a discussion regarding the generic
  power domains code during which we realized that trying to support
  certain combinations of PM config options was painful and not really
  worth it, because nobody would use them in production anyway.  For
  this reason, we decided to make CONFIG_PM_SLEEP select
  CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
  became redundant and CONFIG_PM could be used instead of it.  The
  material here makes that replacement in a major part of the tree, but
  there will be at least one more batch of that in the second part of
  the merge window.

  Specifics:

   - Support for retrieving device properties information from ACPI _DSD
     device configuration objects and a unified device properties
     interface for device drivers (and subsystems) on top of that.  As
     stated above, this works with Device Trees and ACPI and allows
     device drivers to be written in a platform firmware (DT or ACPI)
     agnostic way.  The at25, leds-gpio and gpio_keys_polled drivers are
     now going to use this new interface and the GPIO subsystem is
     additionally modified to allow device drivers to assign names to
     GPIO resources returned by ACPI _CRS objects (in case _DSD is not
     present or does not provide the expected data).  The changes in
     this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
     Lu, and Darren Hart with some fixes from others (Fabio Estevam,
     Geert Uytterhoeven).

   - Support for Hardware Managed Performance States (HWP) as described
     in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
     driver.  CPUID is used to detect whether or not the feature is
     supported by the processor.  If supported, it will be enabled
     automatically unless the intel_pstate=no_hwp switch is present in
     the kernel command line.  From Dirk Brandewie.

   - New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).

   - Support for firmware interface based on ACPI operation regions used
     by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
     platforms for power resource control and thermal management (Aaron
     Lu).

   - Limited support for retrieving off-the-hierarchy dependencies
     between devices from ACPI _DEP device configuration objects and
     deferred probing support for the ACPI battery driver based on the
     _DEP information to make that driver work on Asus T100A (Lan
     Tianyu).

   - New cpufreq driver for the Loongson1B processor (Kelvin Cheung).

   - ACPICA update to upstream revision 20141107 which only affects
     tools (Bob Moore).

   - Fixes for race conditions in the ACPICA's interrupt handling code
     and in the ACPI code related to system suspend and resume (Lv Zheng
     and Rafael J Wysocki).

   - ACPI core fix for an RCU-related issue in the ioremap() regions
     management code that slowed down significantly after CPUs had been
     allowed to enter idle states even if they'd had RCU callbakcs
     queued and triggered some problems in certain proprietary graphics
     driver (and elsewhere).  The fix replaces synchronize_rcu() in that
     code with synchronize_rcu_expedited() which makes the issue go
     away.  From Konstantin Khlebnikov.

   - ACPI LPSS (Low-Power Subsystem) driver fix to handle power
     management of the DMA engine included into the LPSS correctly.  The
     problem is that the DMA engine doesn't have ACPI PM support of its
     own and it simply is turned off when the last LPSS device having
     ACPI PM support goes into D3cold.  To work around that, the PM
     domain used by the ACPI LPSS driver is redesigned so at least one
     device with ACPI PM support will be on as long as the DMA engine is
     in use.  From Andy Shevchenko.

   - ACPI backlight driver fix to avoid using it on "Win8-compatible"
     systems where it doesn't work and where it was used by default by
     mistake (Aaron Lu).

   - Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
     Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
     Chaugule (mostly related to the upcoming ARM64 support).

   - Intel RAPL (Running Average Power Limit) power capping driver fixes
     and improvements including new processor IDs (Jacob Pan).

   - Generic power domains modification to power up domains after
     attaching devices to them to meet the expectations of device
     drivers and bus types assuming devices to be accessible at probe
     time (Ulf Hansson).

   - Preliminary support for controlling device clocks from the generic
     power domains core code and modifications of the ARM/shmobile
     platform to use that feature (Ulf Hansson).

   - Assorted minor fixes and cleanups of the generic power domains core
     code (Ulf Hansson, Geert Uytterhoeven).

   - Assorted minor fixes and cleanups of the device clocks control code
     in the PM core (Geert Uytterhoeven, Grygorii Strashko).

   - Consolidation of device power management Kconfig options by making
     CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
     which is now redundant (Rafael J Wysocki and Kevin Hilman).  That
     is the first batch of the changes needed for this purpose.

   - Core device runtime power management support code cleanup related
     to the execution of callbacks (Andrzej Hajda).

   - cpuidle ARM support improvements (Lorenzo Pieralisi).

   - cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
     new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
     Bartlomiej Zolnierkiewicz).

   - New cpufreq driver callback (->ready) to be executed when the
     cpufreq core is ready to use a given policy object and cpufreq-dt
     driver modification to use that callback for cooling device
     registration (Viresh Kumar).

   - cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
     Geboski, Tomeu Vizoso).

   - Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
     cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
     Stefan Wahren, Petr Cvek).

   - OPP (Operating Performance Points) framework modification to allow
     OPPs to be removed too and update of a few cpufreq drivers
     (cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
     during initialization) on driver removal (Viresh Kumar).

   - Hibernation core fixes and cleanups (Tina Ruchandani and Markus
     Elfring).

   - PM Kconfig fix related to CPU power management (Pankaj Dubey).

   - cpupower tool fix (Prarit Bhargava)"

* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
  i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
  dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  tools: cpupower: fix return checks for sysfs_get_idlestate_count()
  drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
  MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  leds: leds-gpio: Fix multiple instances registration without 'label' property
  iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
  block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
  PM: Merge the SET*_RUNTIME_PM_OPS() macros
  ...

28 files changed, 74 insertions, 44 deletions

diff --git a/arch/arm/include/asm/cpuidle.h b/arch/arm/include/asm/cpuidle.h
index 2fca60ab513a..af319ac4960c 100644
--- a/arch/arm/include/asm/cpuidle.h
+++ b/arch/arm/include/asm/cpuidle.h
@@ -15,7 +15,6 @@ static inline int arm_cpuidle_simple_enter(struct cpuidle_device *dev,
 	.exit_latency           = 1,\
 	.target_residency       = 1,\
 	.power_usage		= p,\
-	.flags                  = CPUIDLE_FLAG_TIME_VALID,\
 	.name                   = "WFI",\
 	.desc                   = "ARM WFI",\
 }
diff --git a/arch/arm/mach-davinci/cpuidle.c b/arch/arm/mach-davinci/cpuidle.c
index f1ac1c94ac0f..b4675fc28f83 100644
--- a/arch/arm/mach-davinci/cpuidle.c
+++ b/arch/arm/mach-davinci/cpuidle.c
@@ -66,7 +66,6 @@ static struct cpuidle_driver davinci_idle_driver = {
 		.enter			= davinci_enter_idle,
 		.exit_latency		= 10,
 		.target_residency	= 10000,
-		.flags			= CPUIDLE_FLAG_TIME_VALID,
 		.name			= "DDR SR",
 		.desc			= "WFI and DDR Self Refresh",
 	},
diff --git a/arch/arm/mach-imx/cpuidle-imx5.c b/arch/arm/mach-imx/cpuidle-imx5.c
index 5a47e3c6172f..3feca526d16b 100644
--- a/arch/arm/mach-imx/cpuidle-imx5.c
+++ b/arch/arm/mach-imx/cpuidle-imx5.c
@@ -24,7 +24,6 @@ static struct cpuidle_driver imx5_cpuidle_driver = {
 		.enter            = imx5_cpuidle_enter,
 		.exit_latency     = 2,
 		.target_residency = 1,
-		.flags            = CPUIDLE_FLAG_TIME_VALID,
 		.name             = "IMX5 SRPG",
 		.desc             = "CPU state retained,powered off",
 	},
diff --git a/arch/arm/mach-imx/cpuidle-imx6q.c b/arch/arm/mach-imx/cpuidle-imx6q.c
index aa935787b743..d76d08623f9f 100644
--- a/arch/arm/mach-imx/cpuidle-imx6q.c
+++ b/arch/arm/mach-imx/cpuidle-imx6q.c
@@ -53,8 +53,7 @@ static struct cpuidle_driver imx6q_cpuidle_driver = {
 		{
 			.exit_latency = 50,
 			.target_residency = 75,
-			.flags = CPUIDLE_FLAG_TIME_VALID |
-			         CPUIDLE_FLAG_TIMER_STOP,
+			.flags = CPUIDLE_FLAG_TIMER_STOP,
 			.enter = imx6q_enter_wait,
 			.name = "WAIT",
 			.desc = "Clock off",
diff --git a/arch/arm/mach-imx/cpuidle-imx6sl.c b/arch/arm/mach-imx/cpuidle-imx6sl.c
index d4b6b8171fa9..7d92e6584551 100644
--- a/arch/arm/mach-imx/cpuidle-imx6sl.c
+++ b/arch/arm/mach-imx/cpuidle-imx6sl.c
@@ -40,8 +40,7 @@ static struct cpuidle_driver imx6sl_cpuidle_driver = {
 		{
 			.exit_latency = 50,
 			.target_residency = 75,
-			.flags = CPUIDLE_FLAG_TIME_VALID |
-				CPUIDLE_FLAG_TIMER_STOP,
+			.flags = CPUIDLE_FLAG_TIMER_STOP,
 			.enter = imx6sl_enter_wait,
 			.name = "WAIT",
 			.desc = "Clock off",
diff --git a/arch/arm/mach-omap2/cpuidle34xx.c b/arch/arm/mach-omap2/cpuidle34xx.c
index e18709d3b95d..aa7b379e2661 100644
--- a/arch/arm/mach-omap2/cpuidle34xx.c
+++ b/arch/arm/mach-omap2/cpuidle34xx.c
@@ -265,7 +265,6 @@ static struct cpuidle_driver omap3_idle_driver = {
 			.enter		  = omap3_enter_idle_bm,
 			.exit_latency	  = 2 + 2,
 			.target_residency = 5,
-			.flags		  = CPUIDLE_FLAG_TIME_VALID,
 			.name		  = "C1",
 			.desc		  = "MPU ON + CORE ON",
 		},
@@ -273,7 +272,6 @@ static struct cpuidle_driver omap3_idle_driver = {
 			.enter		  = omap3_enter_idle_bm,
 			.exit_latency	  = 10 + 10,
 			.target_residency = 30,
-			.flags		  = CPUIDLE_FLAG_TIME_VALID,
 			.name		  = "C2",
 			.desc		  = "MPU ON + CORE ON",
 		},
@@ -281,7 +279,6 @@ static struct cpuidle_driver omap3_idle_driver = {
 			.enter		  = omap3_enter_idle_bm,
 			.exit_latency	  = 50 + 50,
 			.target_residency = 300,
-			.flags		  = CPUIDLE_FLAG_TIME_VALID,
 			.name		  = "C3",
 			.desc		  = "MPU RET + CORE ON",
 		},
@@ -289,7 +286,6 @@ static struct cpuidle_driver omap3_idle_driver = {
 			.enter		  = omap3_enter_idle_bm,
 			.exit_latency	  = 1500 + 1800,
 			.target_residency = 4000,
-			.flags		  = CPUIDLE_FLAG_TIME_VALID,
 			.name		  = "C4",
 			.desc		  = "MPU OFF + CORE ON",
 		},
@@ -297,7 +293,6 @@ static struct cpuidle_driver omap3_idle_driver = {
 			.enter		  = omap3_enter_idle_bm,
 			.exit_latency	  = 2500 + 7500,
 			.target_residency = 12000,
-			.flags		  = CPUIDLE_FLAG_TIME_VALID,
 			.name		  = "C5",
 			.desc		  = "MPU RET + CORE RET",
 		},
@@ -305,7 +300,6 @@ static struct cpuidle_driver omap3_idle_driver = {
 			.enter		  = omap3_enter_idle_bm,
 			.exit_latency	  = 3000 + 8500,
 			.target_residency = 15000,
-			.flags		  = CPUIDLE_FLAG_TIME_VALID,
 			.name		  = "C6",
 			.desc		  = "MPU OFF + CORE RET",
 		},
@@ -313,7 +307,6 @@ static struct cpuidle_driver omap3_idle_driver = {
 			.enter		  = omap3_enter_idle_bm,
 			.exit_latency	  = 10000 + 30000,
 			.target_residency = 30000,
-			.flags		  = CPUIDLE_FLAG_TIME_VALID,
 			.name		  = "C7",
 			.desc		  = "MPU OFF + CORE OFF",
 		},
diff --git a/arch/arm/mach-omap2/cpuidle44xx.c b/arch/arm/mach-omap2/cpuidle44xx.c
index 2498ab025fa2..01e398a868bc 100644
--- a/arch/arm/mach-omap2/cpuidle44xx.c
+++ b/arch/arm/mach-omap2/cpuidle44xx.c
@@ -196,7 +196,6 @@ static struct cpuidle_driver omap4_idle_driver = {
 			/* C1 - CPU0 ON + CPU1 ON + MPU ON */
 			.exit_latency = 2 + 2,
 			.target_residency = 5,
-			.flags = CPUIDLE_FLAG_TIME_VALID,
 			.enter = omap_enter_idle_simple,
 			.name = "C1",
 			.desc = "CPUx ON, MPUSS ON"
@@ -205,7 +204,7 @@ static struct cpuidle_driver omap4_idle_driver = {
 			/* C2 - CPU0 OFF + CPU1 OFF + MPU CSWR */
 			.exit_latency = 328 + 440,
 			.target_residency = 960,
-			.flags = CPUIDLE_FLAG_TIME_VALID | CPUIDLE_FLAG_COUPLED,
+			.flags = CPUIDLE_FLAG_COUPLED,
 			.enter = omap_enter_idle_coupled,
 			.name = "C2",
 			.desc = "CPUx OFF, MPUSS CSWR",
@@ -214,7 +213,7 @@ static struct cpuidle_driver omap4_idle_driver = {
 			/* C3 - CPU0 OFF + CPU1 OFF + MPU OSWR */
 			.exit_latency = 460 + 518,
 			.target_residency = 1100,
-			.flags = CPUIDLE_FLAG_TIME_VALID | CPUIDLE_FLAG_COUPLED,
+			.flags = CPUIDLE_FLAG_COUPLED,
 			.enter = omap_enter_idle_coupled,
 			.name = "C3",
 			.desc = "CPUx OFF, MPUSS OSWR",
diff --git a/arch/arm/mach-s3c24xx/h1940-bluetooth.c b/arch/arm/mach-s3c24xx/h1940-bluetooth.c
index b4d14b864367..9c8b1279a4ba 100644
--- a/arch/arm/mach-s3c24xx/h1940-bluetooth.c
+++ b/arch/arm/mach-s3c24xx/h1940-bluetooth.c
@@ -41,7 +41,7 @@ static void h1940bt_enable(int on)
 		mdelay(10);
 		gpio_set_value(S3C2410_GPH(1), 0);
 
-		h1940_led_blink_set(-EINVAL, GPIO_LED_BLINK, NULL, NULL);
+		h1940_led_blink_set(NULL, GPIO_LED_BLINK, NULL, NULL);
 	}
 	else {
 		gpio_set_value(S3C2410_GPH(1), 1);
@@ -50,7 +50,7 @@ static void h1940bt_enable(int on)
 		mdelay(10);
 		gpio_set_value(H1940_LATCH_BLUETOOTH_POWER, 0);
 
-		h1940_led_blink_set(-EINVAL, GPIO_LED_NO_BLINK_LOW, NULL, NULL);
+		h1940_led_blink_set(NULL, GPIO_LED_NO_BLINK_LOW, NULL, NULL);
 	}
 }
 
diff --git a/arch/arm/mach-s3c24xx/h1940.h b/arch/arm/mach-s3c24xx/h1940.h
index 2950cc466840..596d9f64c5b6 100644
--- a/arch/arm/mach-s3c24xx/h1940.h
+++ b/arch/arm/mach-s3c24xx/h1940.h
@@ -19,8 +19,10 @@
 #define H1940_SUSPEND_RESUMEAT		(0x30081000)
 #define H1940_SUSPEND_CHECK		(0x30080000)
 
+struct gpio_desc;
+
 extern void h1940_pm_return(void);
-extern int h1940_led_blink_set(unsigned gpio, int state,
+extern int h1940_led_blink_set(struct gpio_desc *desc, int state,
 			       unsigned long *delay_on,
 			       unsigned long *delay_off);
 
diff --git a/arch/arm/mach-s3c24xx/mach-h1940.c b/arch/arm/mach-s3c24xx/mach-h1940.c
index d35ddc1d9991..d40d4f5244c6 100644
--- a/arch/arm/mach-s3c24xx/mach-h1940.c
+++ b/arch/arm/mach-s3c24xx/mach-h1940.c
@@ -359,10 +359,11 @@ static struct platform_device h1940_battery = {
 
 static DEFINE_SPINLOCK(h1940_blink_spin);
 
-int h1940_led_blink_set(unsigned gpio, int state,
+int h1940_led_blink_set(struct gpio_desc *desc, int state,
 	unsigned long *delay_on, unsigned long *delay_off)
 {
 	int blink_gpio, check_gpio1, check_gpio2;
+	int gpio = desc ? desc_to_gpio(desc) : -EINVAL;
 
 	switch (gpio) {
 	case H1940_LATCH_LED_GREEN:
diff --git a/arch/arm/mach-s3c24xx/mach-rx1950.c b/arch/arm/mach-s3c24xx/mach-rx1950.c
index c3f2682d0c62..1d35ff375a01 100644
--- a/arch/arm/mach-s3c24xx/mach-rx1950.c
+++ b/arch/arm/mach-s3c24xx/mach-rx1950.c
@@ -250,9 +250,10 @@ static void rx1950_disable_charger(void)
 
 static DEFINE_SPINLOCK(rx1950_blink_spin);
 
-static int rx1950_led_blink_set(unsigned gpio, int state,
+static int rx1950_led_blink_set(struct gpio_desc *desc, int state,
 	unsigned long *delay_on, unsigned long *delay_off)
 {
+	int gpio = desc_to_gpio(desc);
 	int blink_gpio, check_gpio;
 
 	switch (gpio) {
diff --git a/arch/arm/mach-s3c64xx/cpuidle.c b/arch/arm/mach-s3c64xx/cpuidle.c
index 3c8ab07c2012..2eb072440dfa 100644
--- a/arch/arm/mach-s3c64xx/cpuidle.c
+++ b/arch/arm/mach-s3c64xx/cpuidle.c
@@ -48,7 +48,6 @@ static struct cpuidle_driver s3c64xx_cpuidle_driver = {
 			.enter            = s3c64xx_enter_idle,
 			.exit_latency     = 1,
 			.target_residency = 1,
-			.flags            = CPUIDLE_FLAG_TIME_VALID,
 			.name             = "IDLE",
 			.desc             = "System active, ARM gated",
 		},
diff --git a/arch/arm/mach-shmobile/pm-r8a7779.c b/arch/arm/mach-shmobile/pm-r8a7779.c
index 82fe3d7f9662..44a74c4c5a01 100644
--- a/arch/arm/mach-shmobile/pm-r8a7779.c
+++ b/arch/arm/mach-shmobile/pm-r8a7779.c
@@ -83,9 +83,8 @@ static void r8a7779_init_pm_domain(struct r8a7779_pm_domain *r8a7779_pd)
 {
 	struct generic_pm_domain *genpd = &r8a7779_pd->genpd;
 
+	genpd->flags = GENPD_FLAG_PM_CLK;
 	pm_genpd_init(genpd, NULL, false);
-	genpd->dev_ops.stop = pm_clk_suspend;
-	genpd->dev_ops.start = pm_clk_resume;
 	genpd->dev_ops.active_wakeup = pd_active_wakeup;
 	genpd->power_off = pd_power_down;
 	genpd->power_on = pd_power_up;
diff --git a/arch/arm/mach-shmobile/pm-rmobile.c b/arch/arm/mach-shmobile/pm-rmobile.c
index 717e6413d29c..6f7d56ecf969 100644
--- a/arch/arm/mach-shmobile/pm-rmobile.c
+++ b/arch/arm/mach-shmobile/pm-rmobile.c
@@ -106,9 +106,8 @@ static void rmobile_init_pm_domain(struct rmobile_pm_domain *rmobile_pd)
 	struct generic_pm_domain *genpd = &rmobile_pd->genpd;
 	struct dev_power_governor *gov = rmobile_pd->gov;
 
+	genpd->flags = GENPD_FLAG_PM_CLK;
 	pm_genpd_init(genpd, gov ? : &simple_qos_governor, false);
-	genpd->dev_ops.stop		= pm_clk_suspend;
-	genpd->dev_ops.start		= pm_clk_resume;
 	genpd->dev_ops.active_wakeup	= rmobile_pd_active_wakeup;
 	genpd->power_off		= rmobile_pd_power_down;
 	genpd->power_on			= rmobile_pd_power_up;
diff --git a/arch/arm/mach-shmobile/pm-sh7372.c b/arch/arm/mach-shmobile/pm-sh7372.c
index 7e5c2676c489..0e37da654ed5 100644
--- a/arch/arm/mach-shmobile/pm-sh7372.c
+++ b/arch/arm/mach-shmobile/pm-sh7372.c
@@ -423,7 +423,6 @@ static struct cpuidle_driver sh7372_cpuidle_driver = {
 		.desc = "Core Standby Mode",
 		.exit_latency = 10,
 		.target_residency = 20 + 10,
-		.flags = CPUIDLE_FLAG_TIME_VALID,
 		.enter = sh7372_enter_core_standby,
 	},
 	.states[2] = {
@@ -431,7 +430,6 @@ static struct cpuidle_driver sh7372_cpuidle_driver = {
 		.desc = "A3SM PLL ON",
 		.exit_latency = 20,
 		.target_residency = 30 + 20,
-		.flags = CPUIDLE_FLAG_TIME_VALID,
 		.enter = sh7372_enter_a3sm_pll_on,
 	},
 	.states[3] = {
@@ -439,7 +437,6 @@ static struct cpuidle_driver sh7372_cpuidle_driver = {
 		.desc = "A3SM PLL OFF",
 		.exit_latency = 120,
 		.target_residency = 30 + 120,
-		.flags = CPUIDLE_FLAG_TIME_VALID,
 		.enter = sh7372_enter_a3sm_pll_off,
 	},
 	.states[4] = {
@@ -447,7 +444,6 @@ static struct cpuidle_driver sh7372_cpuidle_driver = {
 		.desc = "A4S PLL OFF",
 		.exit_latency = 240,
 		.target_residency = 30 + 240,
-		.flags = CPUIDLE_FLAG_TIME_VALID,
 		.enter = sh7372_enter_a4s,
 		.disabled = true,
 	},
diff --git a/arch/arm/mach-tegra/cpuidle-tegra114.c b/arch/arm/mach-tegra/cpuidle-tegra114.c
index 425b6c8f0cb0..f2b586d7b15d 100644
--- a/arch/arm/mach-tegra/cpuidle-tegra114.c
+++ b/arch/arm/mach-tegra/cpuidle-tegra114.c
@@ -75,7 +75,6 @@ static struct cpuidle_driver tegra_idle_driver = {
 			.exit_latency		= 500,
 			.target_residency	= 1000,
 			.power_usage		= 0,
-			.flags			= CPUIDLE_FLAG_TIME_VALID,
 			.name			= "powered-down",
 			.desc			= "CPU power gated",
 		},
diff --git a/arch/arm/mach-tegra/cpuidle-tegra20.c b/arch/arm/mach-tegra/cpuidle-tegra20.c
index b30bf5cba65b..4f25a7c7ca0f 100644
--- a/arch/arm/mach-tegra/cpuidle-tegra20.c
+++ b/arch/arm/mach-tegra/cpuidle-tegra20.c
@@ -59,8 +59,7 @@ static struct cpuidle_driver tegra_idle_driver = {
 			.exit_latency     = 5000,
 			.target_residency = 10000,
 			.power_usage      = 0,
-			.flags            = CPUIDLE_FLAG_TIME_VALID |
-			CPUIDLE_FLAG_COUPLED,
+			.flags            = CPUIDLE_FLAG_COUPLED,
 			.name             = "powered-down",
 			.desc             = "CPU power gated",
 		},
diff --git a/arch/arm/mach-tegra/cpuidle-tegra30.c b/arch/arm/mach-tegra/cpuidle-tegra30.c
index 35561274f6cf..f8815ed65d9d 100644
--- a/arch/arm/mach-tegra/cpuidle-tegra30.c
+++ b/arch/arm/mach-tegra/cpuidle-tegra30.c
@@ -56,7 +56,6 @@ static struct cpuidle_driver tegra_idle_driver = {
 			.exit_latency		= 2000,
 			.target_residency	= 2200,
 			.power_usage		= 0,
-			.flags			= CPUIDLE_FLAG_TIME_VALID,
 			.name			= "powered-down",
 			.desc			= "CPU power gated",
 		},
diff --git a/arch/arm/plat-orion/gpio.c b/arch/arm/plat-orion/gpio.c
index 14f6e647c739..5168a52a17f9 100644
--- a/arch/arm/plat-orion/gpio.c
+++ b/arch/arm/plat-orion/gpio.c
@@ -306,9 +306,10 @@ EXPORT_SYMBOL(orion_gpio_set_blink);
 
 #define ORION_BLINK_HALF_PERIOD 100 /* ms */
 
-int orion_gpio_led_blink_set(unsigned gpio, int state,
+int orion_gpio_led_blink_set(struct gpio_desc *desc, int state,
 	unsigned long *delay_on, unsigned long *delay_off)
 {
+	unsigned gpio = desc_to_gpio(desc);
 
 	if (delay_on && delay_off && !*delay_on && !*delay_off)
 		*delay_on = *delay_off = ORION_BLINK_HALF_PERIOD;
diff --git a/arch/arm/plat-orion/include/plat/orion-gpio.h b/arch/arm/plat-orion/include/plat/orion-gpio.h
index e763988b04b9..e856b073a9c8 100644
--- a/arch/arm/plat-orion/include/plat/orion-gpio.h
+++ b/arch/arm/plat-orion/include/plat/orion-gpio.h
@@ -14,12 +14,15 @@
 #include <linux/init.h>
 #include <linux/types.h>
 #include <linux/irqdomain.h>
+
+struct gpio_desc;
+
 /*
  * Orion-specific GPIO API extensions.
  */
 void orion_gpio_set_unused(unsigned pin);
 void orion_gpio_set_blink(unsigned pin, int blink);
-int orion_gpio_led_blink_set(unsigned gpio, int state,
+int orion_gpio_led_blink_set(struct gpio_desc *desc, int state,
 	unsigned long *delay_on, unsigned long *delay_off);
 
 #define GPIO_INPUT_OK		(1 << 0)
diff --git a/arch/ia64/Kconfig b/arch/ia64/Kconfig
index c84c88bbbbd7..536d13b0bea6 100644
--- a/arch/ia64/Kconfig
+++ b/arch/ia64/Kconfig
@@ -11,7 +11,6 @@ config IA64
 	select PCI if (!IA64_HP_SIM)
 	select ACPI if (!IA64_HP_SIM)
 	select ARCH_MIGHT_HAVE_ACPI_PDC if ACPI
-	select PM if (!IA64_HP_SIM)
 	select HAVE_UNSTABLE_SCHED_CLOCK
 	select HAVE_IDE
 	select HAVE_OPROFILE
@@ -233,6 +232,7 @@ config IA64_SGI_UV
 config IA64_HP_SIM
 	bool "Ski-simulator"
 	select SWIOTLB
+	depends on !PM_RUNTIME
 
 endchoice
 
diff --git a/arch/mips/include/asm/idle.h b/arch/mips/include/asm/idle.h
index 1c967abd545c..a2d18ab57ac6 100644
--- a/arch/mips/include/asm/idle.h
+++ b/arch/mips/include/asm/idle.h
@@ -22,7 +22,6 @@ extern int mips_cpuidle_wait_enter(struct cpuidle_device *dev,
 	.exit_latency		= 1,\
 	.target_residency	= 1,\
 	.power_usage		= UINT_MAX,\
-	.flags			= CPUIDLE_FLAG_TIME_VALID,\
 	.name			= "wait",\
 	.desc			= "MIPS wait",\
 }
diff --git a/arch/sh/Kconfig b/arch/sh/Kconfig
index 244fb4c81e25..a1403470f80e 100644
--- a/arch/sh/Kconfig
+++ b/arch/sh/Kconfig
@@ -222,7 +222,6 @@ config CPU_SHX3
 config ARCH_SHMOBILE
 	bool
 	select ARCH_SUSPEND_POSSIBLE
-	select PM
 	select PM_RUNTIME
 
 config CPU_HAS_PMU
diff --git a/arch/sh/kernel/cpu/shmobile/cpuidle.c b/arch/sh/kernel/cpu/shmobile/cpuidle.c
index e3abfd4277e2..53b8eeb1db20 100644
--- a/arch/sh/kernel/cpu/shmobile/cpuidle.c
+++ b/arch/sh/kernel/cpu/shmobile/cpuidle.c
@@ -59,7 +59,6 @@ static struct cpuidle_driver cpuidle_driver = {
 			.exit_latency = 1,
 			.target_residency = 1 * 2,
 			.power_usage = 3,
-			.flags = CPUIDLE_FLAG_TIME_VALID,
 			.enter = cpuidle_sleep_enter,
 			.name = "C1",
 			.desc = "SuperH Sleep Mode",
@@ -68,7 +67,6 @@ static struct cpuidle_driver cpuidle_driver = {
 			.exit_latency = 100,
 			.target_residency = 1 * 2,
 			.power_usage = 1,
-			.flags = CPUIDLE_FLAG_TIME_VALID,
 			.enter = cpuidle_sleep_enter,
 			.name = "C2",
 			.desc = "SuperH Sleep Mode [SF]",
@@ -78,7 +76,6 @@ static struct cpuidle_driver cpuidle_driver = {
 			.exit_latency = 2300,
 			.target_residency = 1 * 2,
 			.power_usage = 1,
-			.flags = CPUIDLE_FLAG_TIME_VALID,
 			.enter = cpuidle_sleep_enter,
 			.name = "C3",
 			.desc = "SuperH Mobile Standby Mode [SF]",
diff --git a/arch/x86/include/asm/cpufeature.h b/arch/x86/include/asm/cpufeature.h
index 0bb1335313b2..aede2c347bde 100644
--- a/arch/x86/include/asm/cpufeature.h
+++ b/arch/x86/include/asm/cpufeature.h
@@ -189,6 +189,11 @@
 #define X86_FEATURE_DTHERM	( 7*32+ 7) /* Digital Thermal Sensor */
 #define X86_FEATURE_HW_PSTATE	( 7*32+ 8) /* AMD HW-PState */
 #define X86_FEATURE_PROC_FEEDBACK ( 7*32+ 9) /* AMD ProcFeedbackInterface */
+#define X86_FEATURE_HWP		( 7*32+ 10) /* "hwp" Intel HWP */
+#define X86_FEATURE_HWP_NOITFY	( 7*32+ 11) /* Intel HWP_NOTIFY */
+#define X86_FEATURE_HWP_ACT_WINDOW ( 7*32+ 12) /* Intel HWP_ACT_WINDOW */
+#define X86_FEATURE_HWP_EPP	( 7*32+13) /* Intel HWP_EPP */
+#define X86_FEATURE_HWP_PKG_REQ ( 7*32+14) /* Intel HWP_PKG_REQ */
 
 /* Virtualization flags: Linux defined, word 8 */
 #define X86_FEATURE_TPR_SHADOW  ( 8*32+ 0) /* Intel TPR Shadow */
diff --git a/arch/x86/include/uapi/asm/msr-index.h b/arch/x86/include/uapi/asm/msr-index.h
index 8f02f6990759..c8aa65d56027 100644
--- a/arch/x86/include/uapi/asm/msr-index.h
+++ b/arch/x86/include/uapi/asm/msr-index.h
@@ -152,6 +152,45 @@
 #define MSR_CC6_DEMOTION_POLICY_CONFIG	0x00000668
 #define MSR_MC6_DEMOTION_POLICY_CONFIG	0x00000669
 
+/* Hardware P state interface */
+#define MSR_PPERF			0x0000064e
+#define MSR_PERF_LIMIT_REASONS		0x0000064f
+#define MSR_PM_ENABLE			0x00000770
+#define MSR_HWP_CAPABILITIES		0x00000771
+#define MSR_HWP_REQUEST_PKG		0x00000772
+#define MSR_HWP_INTERRUPT		0x00000773
+#define MSR_HWP_REQUEST 		0x00000774
+#define MSR_HWP_STATUS			0x00000777
+
+/* CPUID.6.EAX */
+#define HWP_BASE_BIT			(1<<7)
+#define HWP_NOTIFICATIONS_BIT		(1<<8)
+#define HWP_ACTIVITY_WINDOW_BIT		(1<<9)
+#define HWP_ENERGY_PERF_PREFERENCE_BIT	(1<<10)
+#define HWP_PACKAGE_LEVEL_REQUEST_BIT	(1<<11)
+
+/* IA32_HWP_CAPABILITIES */
+#define HWP_HIGHEST_PERF(x)		(x & 0xff)
+#define HWP_GUARANTEED_PERF(x)		((x & (0xff << 8)) >>8)
+#define HWP_MOSTEFFICIENT_PERF(x)	((x & (0xff << 16)) >>16)
+#define HWP_LOWEST_PERF(x)		((x & (0xff << 24)) >>24)
+
+/* IA32_HWP_REQUEST */
+#define HWP_MIN_PERF(x) 		(x & 0xff)
+#define HWP_MAX_PERF(x) 		((x & 0xff) << 8)
+#define HWP_DESIRED_PERF(x)		((x & 0xff) << 16)
+#define HWP_ENERGY_PERF_PREFERENCE(x)	((x & 0xff) << 24)
+#define HWP_ACTIVITY_WINDOW(x)		((x & 0xff3) << 32)
+#define HWP_PACKAGE_CONTROL(x)		((x & 0x1) << 42)
+
+/* IA32_HWP_STATUS */
+#define HWP_GUARANTEED_CHANGE(x)	(x & 0x1)
+#define HWP_EXCURSION_TO_MINIMUM(x)	(x & 0x4)
+
+/* IA32_HWP_INTERRUPT */
+#define HWP_CHANGE_TO_GUARANTEED_INT(x)	(x & 0x1)
+#define HWP_EXCURSION_TO_MINIMUM_INT(x)	(x & 0x2)
+
 #define MSR_AMD64_MC0_MASK		0xc0010044
 
 #define MSR_IA32_MCx_CTL(x)		(MSR_IA32_MC0_CTL + 4*(x))
@@ -346,6 +385,8 @@
 
 #define MSR_IA32_TEMPERATURE_TARGET	0x000001a2
 
+#define MSR_MISC_PWR_MGMT		0x000001aa
+
 #define MSR_IA32_ENERGY_PERF_BIAS	0x000001b0
 #define ENERGY_PERF_BIAS_PERFORMANCE	0
 #define ENERGY_PERF_BIAS_NORMAL		6
diff --git a/arch/x86/kernel/apm_32.c b/arch/x86/kernel/apm_32.c
index 584874451414..927ec9235947 100644
--- a/arch/x86/kernel/apm_32.c
+++ b/arch/x86/kernel/apm_32.c
@@ -378,7 +378,6 @@ static struct cpuidle_driver apm_idle_driver = {
 		{ /* entry 1 is for APM idle */
 			.name = "APM",
 			.desc = "APM idle",
-			.flags = CPUIDLE_FLAG_TIME_VALID,
 			.exit_latency = 250,	/* WAG */
 			.target_residency = 500,	/* WAG */
 			.enter = &apm_cpu_idle
diff --git a/arch/x86/kernel/cpu/scattered.c b/arch/x86/kernel/cpu/scattered.c
index 4a8013d55947..60639093d536 100644
--- a/arch/x86/kernel/cpu/scattered.c
+++ b/arch/x86/kernel/cpu/scattered.c
@@ -36,6 +36,11 @@ void init_scattered_cpuid_features(struct cpuinfo_x86 *c)
 		{ X86_FEATURE_ARAT,		CR_EAX, 2, 0x00000006, 0 },
 		{ X86_FEATURE_PLN,		CR_EAX, 4, 0x00000006, 0 },
 		{ X86_FEATURE_PTS,		CR_EAX, 6, 0x00000006, 0 },
+		{ X86_FEATURE_HWP,		CR_EAX, 7, 0x00000006, 0 },
+		{ X86_FEATURE_HWP_NOITFY,	CR_EAX, 8, 0x00000006, 0 },
+		{ X86_FEATURE_HWP_ACT_WINDOW,	CR_EAX, 9, 0x00000006, 0 },
+		{ X86_FEATURE_HWP_EPP,		CR_EAX,10, 0x00000006, 0 },
+		{ X86_FEATURE_HWP_PKG_REQ,	CR_EAX,11, 0x00000006, 0 },
 		{ X86_FEATURE_APERFMPERF,	CR_ECX, 0, 0x00000006, 0 },
 		{ X86_FEATURE_EPB,		CR_ECX, 3, 0x00000006, 0 },
 		{ X86_FEATURE_HW_PSTATE,	CR_EDX, 7, 0x80000007, 0 },