summaryrefslogtreecommitdiff
path: root/drivers/i2c
diff options
context:
space:
mode:
authorAlexander Sverdlin <alexander.sverdlin@nokia.com>2015-11-30 15:51:00 +0100
committerWolfram Sang <wsa@the-dreams.de>2015-11-30 15:55:07 +0100
commit87cb5b425fa32094972868b50e65083c586509a3 (patch)
treee35e86770755cdd62ba403d90a62923f6d74492e /drivers/i2c
parentbba61f50f76574ca5b84b310925be7c2e8e64275 (diff)
i2c: davinci: Increase module clock frequency
I2C controller used in Keystone SoC has an undocumented peculiarity which results in SDA-SCL margins being dependent on module clock. Driving high capacity bus near its limits can result in STOP condition sometimes being understood as REPEATED-START by slaves (or NACK instead of ACK, etc...). Driving the module with higher clocks increases the margin between SDA and SCL transitions, making the operations with higher bus rates more robust. Therefore, target the module clock to 12MHz instead of 7MHz, still staying within the specification limits. Before the change STOP timing looked like this on 400kHz: SDA ----------+ +---- \ / \ / +----+ (1) SCL --+ +------------ \ / \ / +----+ (2) While only point (1) signals STOP, point (2) could be incorrectly recognized as repeated-START (almost no margin between SDA and SCL transitions). After the change there is at least 600ns margin measured between SCL fall and SDA fall during STOP generation: SDA ------+ +---- \ / \ / +----+ SCL --+ +-------- \ / \ / +----+ ->| |<- 600ns ->| |<- tSUSTO So called tSUSTO (setup time for STOP condition) is still slightly higher than 600ns, so no problem here. Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Acked-by: Santosh Shilimkar <ssantosh@kernel.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Diffstat (limited to 'drivers/i2c')
-rw-r--r--drivers/i2c/busses/i2c-davinci.c11
1 files changed, 9 insertions, 2 deletions
diff --git a/drivers/i2c/busses/i2c-davinci.c b/drivers/i2c/busses/i2c-davinci.c
index c5628a42170a..a8bdcb5292f5 100644
--- a/drivers/i2c/busses/i2c-davinci.c
+++ b/drivers/i2c/busses/i2c-davinci.c
@@ -202,8 +202,15 @@ static void i2c_davinci_calc_clk_dividers(struct davinci_i2c_dev *dev)
* d is always 6 on Keystone I2C controller
*/
- /* get minimum of 7 MHz clock, but max of 12 MHz */
- psc = (input_clock / 7000000) - 1;
+ /*
+ * Both Davinci and current Keystone User Guides recommend a value
+ * between 7MHz and 12MHz. In reality 7MHz module clock doesn't
+ * always produce enough margin between SDA and SCL transitions.
+ * Measurements show that the higher the module clock is, the
+ * bigger is the margin, providing more reliable communication.
+ * So we better target for 12MHz.
+ */
+ psc = (input_clock / 12000000) - 1;
if ((input_clock / (psc + 1)) > 12000000)
psc++; /* better to run under spec than over */
d = (psc >= 2) ? 5 : 7 - psc;