mmc: Move host and card drivers to subdirs

Clean up the drivers/mmc directory by moving card and host drivers
into subdirectories.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

1 files changed, 1031 insertions, 0 deletions

diff --git a/drivers/mmc/host/au1xmmc.c b/drivers/mmc/host/au1xmmc.c
new file mode 100644
index 000000000000..b7156a4555b5
--- /dev/null
+++ b/drivers/mmc/host/au1xmmc.c
@@ -0,0 +1,1031 @@
+/*
+ * linux/drivers/mmc/au1xmmc.c - AU1XX0 MMC driver
+ *
+ *  Copyright (c) 2005, Advanced Micro Devices, Inc.
+ *
+ *  Developed with help from the 2.4.30 MMC AU1XXX controller including
+ *  the following copyright notices:
+ *     Copyright (c) 2003-2004 Embedded Edge, LLC.
+ *     Portions Copyright (C) 2002 Embedix, Inc
+ *     Copyright 2002 Hewlett-Packard Company
+
+ *  2.6 version of this driver inspired by:
+ *     (drivers/mmc/wbsd.c) Copyright (C) 2004-2005 Pierre Ossman,
+ *     All Rights Reserved.
+ *     (drivers/mmc/pxa.c) Copyright (C) 2003 Russell King,
+ *     All Rights Reserved.
+ *
+
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/* Why is a timer used to detect insert events?
+ *
+ * From the AU1100 MMC application guide:
+ * If the Au1100-based design is intended to support both MultiMediaCards
+ * and 1- or 4-data bit SecureDigital cards, then the solution is to
+ * connect a weak (560KOhm) pull-up resistor to connector pin 1.
+ * In doing so, a MMC card never enters SPI-mode communications,
+ * but now the SecureDigital card-detect feature of CD/DAT3 is ineffective
+ * (the low to high transition will not occur).
+ *
+ * So we use the timer to check the status manually.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mm.h>
+#include <linux/interrupt.h>
+#include <linux/dma-mapping.h>
+
+#include <linux/mmc/host.h>
+#include <asm/io.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/au1xxx_dbdma.h>
+#include <asm/mach-au1x00/au1100_mmc.h>
+#include <asm/scatterlist.h>
+
+#include <au1xxx.h>
+#include "au1xmmc.h"
+
+#define DRIVER_NAME "au1xxx-mmc"
+
+/* Set this to enable special debugging macros */
+
+#ifdef DEBUG
+#define DBG(fmt, idx, args...) printk("au1xx(%d): DEBUG: " fmt, idx, ##args)
+#else
+#define DBG(fmt, idx, args...)
+#endif
+
+const struct {
+	u32 iobase;
+	u32 tx_devid, rx_devid;
+	u16 bcsrpwr;
+	u16 bcsrstatus;
+	u16 wpstatus;
+} au1xmmc_card_table[] = {
+	{ SD0_BASE, DSCR_CMD0_SDMS_TX0, DSCR_CMD0_SDMS_RX0,
+	  BCSR_BOARD_SD0PWR, BCSR_INT_SD0INSERT, BCSR_STATUS_SD0WP },
+#ifndef CONFIG_MIPS_DB1200
+	{ SD1_BASE, DSCR_CMD0_SDMS_TX1, DSCR_CMD0_SDMS_RX1,
+	  BCSR_BOARD_DS1PWR, BCSR_INT_SD1INSERT, BCSR_STATUS_SD1WP }
+#endif
+};
+
+#define AU1XMMC_CONTROLLER_COUNT \
+	(sizeof(au1xmmc_card_table) / sizeof(au1xmmc_card_table[0]))
+
+/* This array stores pointers for the hosts (used by the IRQ handler) */
+struct au1xmmc_host *au1xmmc_hosts[AU1XMMC_CONTROLLER_COUNT];
+static int dma = 1;
+
+#ifdef MODULE
+module_param(dma, bool, 0);
+MODULE_PARM_DESC(dma, "Use DMA engine for data transfers (0 = disabled)");
+#endif
+
+static inline void IRQ_ON(struct au1xmmc_host *host, u32 mask)
+{
+	u32 val = au_readl(HOST_CONFIG(host));
+	val |= mask;
+	au_writel(val, HOST_CONFIG(host));
+	au_sync();
+}
+
+static inline void FLUSH_FIFO(struct au1xmmc_host *host)
+{
+	u32 val = au_readl(HOST_CONFIG2(host));
+
+	au_writel(val | SD_CONFIG2_FF, HOST_CONFIG2(host));
+	au_sync_delay(1);
+
+	/* SEND_STOP will turn off clock control - this re-enables it */
+	val &= ~SD_CONFIG2_DF;
+
+	au_writel(val, HOST_CONFIG2(host));
+	au_sync();
+}
+
+static inline void IRQ_OFF(struct au1xmmc_host *host, u32 mask)
+{
+	u32 val = au_readl(HOST_CONFIG(host));
+	val &= ~mask;
+	au_writel(val, HOST_CONFIG(host));
+	au_sync();
+}
+
+static inline void SEND_STOP(struct au1xmmc_host *host)
+{
+
+	/* We know the value of CONFIG2, so avoid a read we don't need */
+	u32 mask = SD_CONFIG2_EN;
+
+	WARN_ON(host->status != HOST_S_DATA);
+	host->status = HOST_S_STOP;
+
+	au_writel(mask | SD_CONFIG2_DF, HOST_CONFIG2(host));
+	au_sync();
+
+	/* Send the stop commmand */
+	au_writel(STOP_CMD, HOST_CMD(host));
+}
+
+static void au1xmmc_set_power(struct au1xmmc_host *host, int state)
+{
+
+	u32 val = au1xmmc_card_table[host->id].bcsrpwr;
+
+	bcsr->board &= ~val;
+	if (state) bcsr->board |= val;
+
+	au_sync_delay(1);
+}
+
+static inline int au1xmmc_card_inserted(struct au1xmmc_host *host)
+{
+	return (bcsr->sig_status & au1xmmc_card_table[host->id].bcsrstatus)
+		? 1 : 0;
+}
+
+static int au1xmmc_card_readonly(struct mmc_host *mmc)
+{
+	struct au1xmmc_host *host = mmc_priv(mmc);
+	return (bcsr->status & au1xmmc_card_table[host->id].wpstatus)
+		? 1 : 0;
+}
+
+static void au1xmmc_finish_request(struct au1xmmc_host *host)
+{
+
+	struct mmc_request *mrq = host->mrq;
+
+	host->mrq = NULL;
+	host->flags &= HOST_F_ACTIVE;
+
+	host->dma.len = 0;
+	host->dma.dir = 0;
+
+	host->pio.index  = 0;
+	host->pio.offset = 0;
+	host->pio.len = 0;
+
+	host->status = HOST_S_IDLE;
+
+	bcsr->disk_leds |= (1 << 8);
+
+	mmc_request_done(host->mmc, mrq);
+}
+
+static void au1xmmc_tasklet_finish(unsigned long param)
+{
+	struct au1xmmc_host *host = (struct au1xmmc_host *) param;
+	au1xmmc_finish_request(host);
+}
+
+static int au1xmmc_send_command(struct au1xmmc_host *host, int wait,
+				struct mmc_command *cmd)
+{
+
+	u32 mmccmd = (cmd->opcode << SD_CMD_CI_SHIFT);
+
+	switch (mmc_resp_type(cmd)) {
+	case MMC_RSP_NONE:
+		break;
+	case MMC_RSP_R1:
+		mmccmd |= SD_CMD_RT_1;
+		break;
+	case MMC_RSP_R1B:
+		mmccmd |= SD_CMD_RT_1B;
+		break;
+	case MMC_RSP_R2:
+		mmccmd |= SD_CMD_RT_2;
+		break;
+	case MMC_RSP_R3:
+		mmccmd |= SD_CMD_RT_3;
+		break;
+	default:
+		printk(KERN_INFO "au1xmmc: unhandled response type %02x\n",
+			mmc_resp_type(cmd));
+		return MMC_ERR_INVALID;
+	}
+
+	switch(cmd->opcode) {
+	case MMC_READ_SINGLE_BLOCK:
+	case SD_APP_SEND_SCR:
+		mmccmd |= SD_CMD_CT_2;
+		break;
+	case MMC_READ_MULTIPLE_BLOCK:
+		mmccmd |= SD_CMD_CT_4;
+		break;
+	case MMC_WRITE_BLOCK:
+		mmccmd |= SD_CMD_CT_1;
+		break;
+
+	case MMC_WRITE_MULTIPLE_BLOCK:
+		mmccmd |= SD_CMD_CT_3;
+		break;
+	case MMC_STOP_TRANSMISSION:
+		mmccmd |= SD_CMD_CT_7;
+		break;
+	}
+
+	au_writel(cmd->arg, HOST_CMDARG(host));
+	au_sync();
+
+	if (wait)
+		IRQ_OFF(host, SD_CONFIG_CR);
+
+	au_writel((mmccmd | SD_CMD_GO), HOST_CMD(host));
+	au_sync();
+
+	/* Wait for the command to go on the line */
+
+	while(1) {
+		if (!(au_readl(HOST_CMD(host)) & SD_CMD_GO))
+			break;
+	}
+
+	/* Wait for the command to come back */
+
+	if (wait) {
+		u32 status = au_readl(HOST_STATUS(host));
+
+		while(!(status & SD_STATUS_CR))
+			status = au_readl(HOST_STATUS(host));
+
+		/* Clear the CR status */
+		au_writel(SD_STATUS_CR, HOST_STATUS(host));
+
+		IRQ_ON(host, SD_CONFIG_CR);
+	}
+
+	return MMC_ERR_NONE;
+}
+
+static void au1xmmc_data_complete(struct au1xmmc_host *host, u32 status)
+{
+
+	struct mmc_request *mrq = host->mrq;
+	struct mmc_data *data;
+	u32 crc;
+
+	WARN_ON(host->status != HOST_S_DATA && host->status != HOST_S_STOP);
+
+	if (host->mrq == NULL)
+		return;
+
+	data = mrq->cmd->data;
+
+	if (status == 0)
+		status = au_readl(HOST_STATUS(host));
+
+	/* The transaction is really over when the SD_STATUS_DB bit is clear */
+
+	while((host->flags & HOST_F_XMIT) && (status & SD_STATUS_DB))
+		status = au_readl(HOST_STATUS(host));
+
+	data->error = MMC_ERR_NONE;
+	dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len, host->dma.dir);
+
+        /* Process any errors */
+
+	crc = (status & (SD_STATUS_WC | SD_STATUS_RC));
+	if (host->flags & HOST_F_XMIT)
+		crc |= ((status & 0x07) == 0x02) ? 0 : 1;
+
+	if (crc)
+		data->error = MMC_ERR_BADCRC;
+
+	/* Clear the CRC bits */
+	au_writel(SD_STATUS_WC | SD_STATUS_RC, HOST_STATUS(host));
+
+	data->bytes_xfered = 0;
+
+	if (data->error == MMC_ERR_NONE) {
+		if (host->flags & HOST_F_DMA) {
+			u32 chan = DMA_CHANNEL(host);
+
+			chan_tab_t *c = *((chan_tab_t **) chan);
+			au1x_dma_chan_t *cp = c->chan_ptr;
+			data->bytes_xfered = cp->ddma_bytecnt;
+		}
+		else
+			data->bytes_xfered =
+				(data->blocks * data->blksz) -
+				host->pio.len;
+	}
+
+	au1xmmc_finish_request(host);
+}
+
+static void au1xmmc_tasklet_data(unsigned long param)
+{
+	struct au1xmmc_host *host = (struct au1xmmc_host *) param;
+
+	u32 status = au_readl(HOST_STATUS(host));
+	au1xmmc_data_complete(host, status);
+}
+
+#define AU1XMMC_MAX_TRANSFER 8
+
+static void au1xmmc_send_pio(struct au1xmmc_host *host)
+{
+
+	struct mmc_data *data = 0;
+	int sg_len, max, count = 0;
+	unsigned char *sg_ptr;
+	u32 status = 0;
+	struct scatterlist *sg;
+
+	data = host->mrq->data;
+
+	if (!(host->flags & HOST_F_XMIT))
+		return;
+
+	/* This is the pointer to the data buffer */
+	sg = &data->sg[host->pio.index];
+	sg_ptr = page_address(sg->page) + sg->offset + host->pio.offset;
+
+	/* This is the space left inside the buffer */
+	sg_len = data->sg[host->pio.index].length - host->pio.offset;
+
+	/* Check to if we need less then the size of the sg_buffer */
+
+	max = (sg_len > host->pio.len) ? host->pio.len : sg_len;
+	if (max > AU1XMMC_MAX_TRANSFER) max = AU1XMMC_MAX_TRANSFER;
+
+	for(count = 0; count < max; count++ ) {
+		unsigned char val;
+
+		status = au_readl(HOST_STATUS(host));
+
+		if (!(status & SD_STATUS_TH))
+			break;
+
+		val = *sg_ptr++;
+
+		au_writel((unsigned long) val, HOST_TXPORT(host));
+		au_sync();
+	}
+
+	host->pio.len -= count;
+	host->pio.offset += count;
+
+	if (count == sg_len) {
+		host->pio.index++;
+		host->pio.offset = 0;
+	}
+
+	if (host->pio.len == 0) {
+		IRQ_OFF(host, SD_CONFIG_TH);
+
+		if (host->flags & HOST_F_STOP)
+			SEND_STOP(host);
+
+		tasklet_schedule(&host->data_task);
+	}
+}
+
+static void au1xmmc_receive_pio(struct au1xmmc_host *host)
+{
+
+	struct mmc_data *data = 0;
+	int sg_len = 0, max = 0, count = 0;
+	unsigned char *sg_ptr = 0;
+	u32 status = 0;
+	struct scatterlist *sg;
+
+	data = host->mrq->data;
+
+	if (!(host->flags & HOST_F_RECV))
+		return;
+
+	max = host->pio.len;
+
+	if (host->pio.index < host->dma.len) {
+		sg = &data->sg[host->pio.index];
+		sg_ptr = page_address(sg->page) + sg->offset + host->pio.offset;
+
+		/* This is the space left inside the buffer */
+		sg_len = sg_dma_len(&data->sg[host->pio.index]) - host->pio.offset;
+
+		/* Check to if we need less then the size of the sg_buffer */
+		if (sg_len < max) max = sg_len;
+	}
+
+	if (max > AU1XMMC_MAX_TRANSFER)
+		max = AU1XMMC_MAX_TRANSFER;
+
+	for(count = 0; count < max; count++ ) {
+		u32 val;
+		status = au_readl(HOST_STATUS(host));
+
+		if (!(status & SD_STATUS_NE))
+			break;
+
+		if (status & SD_STATUS_RC) {
+			DBG("RX CRC Error [%d + %d].\n", host->id,
+					host->pio.len, count);
+			break;
+		}
+
+		if (status & SD_STATUS_RO) {
+			DBG("RX Overrun [%d + %d]\n", host->id,
+					host->pio.len, count);
+			break;
+		}
+		else if (status & SD_STATUS_RU) {
+			DBG("RX Underrun [%d + %d]\n", host->id,
+					host->pio.len,	count);
+			break;
+		}
+
+		val = au_readl(HOST_RXPORT(host));
+
+		if (sg_ptr)
+			*sg_ptr++ = (unsigned char) (val & 0xFF);
+	}
+
+	host->pio.len -= count;
+	host->pio.offset += count;
+
+	if (sg_len && count == sg_len) {
+		host->pio.index++;
+		host->pio.offset = 0;
+	}
+
+	if (host->pio.len == 0) {
+		//IRQ_OFF(host, SD_CONFIG_RA | SD_CONFIG_RF);
+		IRQ_OFF(host, SD_CONFIG_NE);
+
+		if (host->flags & HOST_F_STOP)
+			SEND_STOP(host);
+
+		tasklet_schedule(&host->data_task);
+	}
+}
+
+/* static void au1xmmc_cmd_complete
+   This is called when a command has been completed - grab the response
+   and check for errors.  Then start the data transfer if it is indicated.
+*/
+
+static void au1xmmc_cmd_complete(struct au1xmmc_host *host, u32 status)
+{
+
+	struct mmc_request *mrq = host->mrq;
+	struct mmc_command *cmd;
+	int trans;
+
+	if (!host->mrq)
+		return;
+
+	cmd = mrq->cmd;
+	cmd->error = MMC_ERR_NONE;
+
+	if (cmd->flags & MMC_RSP_PRESENT) {
+		if (cmd->flags & MMC_RSP_136) {
+			u32 r[4];
+			int i;
+
+			r[0] = au_readl(host->iobase + SD_RESP3);
+			r[1] = au_readl(host->iobase + SD_RESP2);
+			r[2] = au_readl(host->iobase + SD_RESP1);
+			r[3] = au_readl(host->iobase + SD_RESP0);
+
+			/* The CRC is omitted from the response, so really
+			 * we only got 120 bytes, but the engine expects
+			 * 128 bits, so we have to shift things up
+			 */
+
+			for(i = 0; i < 4; i++) {
+				cmd->resp[i] = (r[i] & 0x00FFFFFF) << 8;
+				if (i != 3)
+					cmd->resp[i] |= (r[i + 1] & 0xFF000000) >> 24;
+			}
+		} else {
+			/* Techincally, we should be getting all 48 bits of
+			 * the response (SD_RESP1 + SD_RESP2), but because
+			 * our response omits the CRC, our data ends up
+			 * being shifted 8 bits to the right.  In this case,
+			 * that means that the OSR data starts at bit 31,
+			 * so we can just read RESP0 and return that
+			 */
+			cmd->resp[0] = au_readl(host->iobase + SD_RESP0);
+		}
+	}
+
+        /* Figure out errors */
+
+	if (status & (SD_STATUS_SC | SD_STATUS_WC | SD_STATUS_RC))
+		cmd->error = MMC_ERR_BADCRC;
+
+	trans = host->flags & (HOST_F_XMIT | HOST_F_RECV);
+
+	if (!trans || cmd->error != MMC_ERR_NONE) {
+
+		IRQ_OFF(host, SD_CONFIG_TH | SD_CONFIG_RA|SD_CONFIG_RF);
+		tasklet_schedule(&host->finish_task);
+		return;
+	}
+
+	host->status = HOST_S_DATA;
+
+	if (host->flags & HOST_F_DMA) {
+		u32 channel = DMA_CHANNEL(host);
+
+		/* Start the DMA as soon as the buffer gets something in it */
+
+		if (host->flags & HOST_F_RECV) {
+			u32 mask = SD_STATUS_DB | SD_STATUS_NE;
+
+			while((status & mask) != mask)
+				status = au_readl(HOST_STATUS(host));
+		}
+
+		au1xxx_dbdma_start(channel);
+	}
+}
+
+static void au1xmmc_set_clock(struct au1xmmc_host *host, int rate)
+{
+
+	unsigned int pbus = get_au1x00_speed();
+	unsigned int divisor;
+	u32 config;
+
+	/* From databook:
+	   divisor = ((((cpuclock / sbus_divisor) / 2) / mmcclock) / 2) - 1
+	*/
+
+	pbus /= ((au_readl(SYS_POWERCTRL) & 0x3) + 2);
+	pbus /= 2;
+
+	divisor = ((pbus / rate) / 2) - 1;
+
+	config = au_readl(HOST_CONFIG(host));
+
+	config &= ~(SD_CONFIG_DIV);
+	config |= (divisor & SD_CONFIG_DIV) | SD_CONFIG_DE;
+
+	au_writel(config, HOST_CONFIG(host));
+	au_sync();
+}
+
+static int
+au1xmmc_prepare_data(struct au1xmmc_host *host, struct mmc_data *data)
+{
+
+	int datalen = data->blocks * data->blksz;
+
+	if (dma != 0)
+		host->flags |= HOST_F_DMA;
+
+	if (data->flags & MMC_DATA_READ)
+		host->flags |= HOST_F_RECV;
+	else
+		host->flags |= HOST_F_XMIT;
+
+	if (host->mrq->stop)
+		host->flags |= HOST_F_STOP;
+
+	host->dma.dir = DMA_BIDIRECTIONAL;
+
+	host->dma.len = dma_map_sg(mmc_dev(host->mmc), data->sg,
+				   data->sg_len, host->dma.dir);
+
+	if (host->dma.len == 0)
+		return MMC_ERR_TIMEOUT;
+
+	au_writel(data->blksz - 1, HOST_BLKSIZE(host));
+
+	if (host->flags & HOST_F_DMA) {
+		int i;
+		u32 channel = DMA_CHANNEL(host);
+
+		au1xxx_dbdma_stop(channel);
+
+		for(i = 0; i < host->dma.len; i++) {
+			u32 ret = 0, flags = DDMA_FLAGS_NOIE;
+			struct scatterlist *sg = &data->sg[i];
+			int sg_len = sg->length;
+
+			int len = (datalen > sg_len) ? sg_len : datalen;
+
+			if (i == host->dma.len - 1)
+				flags = DDMA_FLAGS_IE;
+
+    			if (host->flags & HOST_F_XMIT){
+      				ret = au1xxx_dbdma_put_source_flags(channel,
+					(void *) (page_address(sg->page) +
+						  sg->offset),
+					len, flags);
+			}
+    			else {
+      				ret = au1xxx_dbdma_put_dest_flags(channel,
+					(void *) (page_address(sg->page) +
+						  sg->offset),
+					len, flags);
+			}
+
+    			if (!ret)
+				goto dataerr;
+
+			datalen -= len;
+		}
+	}
+	else {
+		host->pio.index = 0;
+		host->pio.offset = 0;
+		host->pio.len = datalen;
+
+		if (host->flags & HOST_F_XMIT)
+			IRQ_ON(host, SD_CONFIG_TH);
+		else
+			IRQ_ON(host, SD_CONFIG_NE);
+			//IRQ_ON(host, SD_CONFIG_RA|SD_CONFIG_RF);
+	}
+
+	return MMC_ERR_NONE;
+
+ dataerr:
+	dma_unmap_sg(mmc_dev(host->mmc),data->sg,data->sg_len,host->dma.dir);
+	return MMC_ERR_TIMEOUT;
+}
+
+/* static void au1xmmc_request
+   This actually starts a command or data transaction
+*/
+
+static void au1xmmc_request(struct mmc_host* mmc, struct mmc_request* mrq)
+{
+
+	struct au1xmmc_host *host = mmc_priv(mmc);
+	int ret = MMC_ERR_NONE;
+
+	WARN_ON(irqs_disabled());
+	WARN_ON(host->status != HOST_S_IDLE);
+
+	host->mrq = mrq;
+	host->status = HOST_S_CMD;
+
+	bcsr->disk_leds &= ~(1 << 8);
+
+	if (mrq->data) {
+		FLUSH_FIFO(host);
+		ret = au1xmmc_prepare_data(host, mrq->data);
+	}
+
+	if (ret == MMC_ERR_NONE)
+		ret = au1xmmc_send_command(host, 0, mrq->cmd);
+
+	if (ret != MMC_ERR_NONE) {
+		mrq->cmd->error = ret;
+		au1xmmc_finish_request(host);
+	}
+}
+
+static void au1xmmc_reset_controller(struct au1xmmc_host *host)
+{
+
+	/* Apply the clock */
+	au_writel(SD_ENABLE_CE, HOST_ENABLE(host));
+        au_sync_delay(1);
+
+	au_writel(SD_ENABLE_R | SD_ENABLE_CE, HOST_ENABLE(host));
+	au_sync_delay(5);
+
+	au_writel(~0, HOST_STATUS(host));
+	au_sync();
+
+	au_writel(0, HOST_BLKSIZE(host));
+	au_writel(0x001fffff, HOST_TIMEOUT(host));
+	au_sync();
+
+	au_writel(SD_CONFIG2_EN, HOST_CONFIG2(host));
+        au_sync();
+
+	au_writel(SD_CONFIG2_EN | SD_CONFIG2_FF, HOST_CONFIG2(host));
+	au_sync_delay(1);
+
+	au_writel(SD_CONFIG2_EN, HOST_CONFIG2(host));
+	au_sync();
+
+	/* Configure interrupts */
+	au_writel(AU1XMMC_INTERRUPTS, HOST_CONFIG(host));
+	au_sync();
+}
+
+
+static void au1xmmc_set_ios(struct mmc_host* mmc, struct mmc_ios* ios)
+{
+	struct au1xmmc_host *host = mmc_priv(mmc);
+
+	if (ios->power_mode == MMC_POWER_OFF)
+		au1xmmc_set_power(host, 0);
+	else if (ios->power_mode == MMC_POWER_ON) {
+		au1xmmc_set_power(host, 1);
+	}
+
+	if (ios->clock && ios->clock != host->clock) {
+		au1xmmc_set_clock(host, ios->clock);
+		host->clock = ios->clock;
+	}
+}
+
+static void au1xmmc_dma_callback(int irq, void *dev_id)
+{
+	struct au1xmmc_host *host = (struct au1xmmc_host *) dev_id;
+
+	/* Avoid spurious interrupts */
+
+	if (!host->mrq)
+		return;
+
+	if (host->flags & HOST_F_STOP)
+		SEND_STOP(host);
+
+	tasklet_schedule(&host->data_task);
+}
+
+#define STATUS_TIMEOUT (SD_STATUS_RAT | SD_STATUS_DT)
+#define STATUS_DATA_IN  (SD_STATUS_NE)
+#define STATUS_DATA_OUT (SD_STATUS_TH)
+
+static irqreturn_t au1xmmc_irq(int irq, void *dev_id)
+{
+
+	u32 status;
+	int i, ret = 0;
+
+	disable_irq(AU1100_SD_IRQ);
+
+	for(i = 0; i < AU1XMMC_CONTROLLER_COUNT; i++) {
+		struct au1xmmc_host * host = au1xmmc_hosts[i];
+		u32 handled = 1;
+
+		status = au_readl(HOST_STATUS(host));
+
+		if (host->mrq && (status & STATUS_TIMEOUT)) {
+			if (status & SD_STATUS_RAT)
+				host->mrq->cmd->error = MMC_ERR_TIMEOUT;
+
+			else if (status & SD_STATUS_DT)
+				host->mrq->data->error = MMC_ERR_TIMEOUT;
+
+			/* In PIO mode, interrupts might still be enabled */
+			IRQ_OFF(host, SD_CONFIG_NE | SD_CONFIG_TH);
+
+			//IRQ_OFF(host, SD_CONFIG_TH|SD_CONFIG_RA|SD_CONFIG_RF);
+			tasklet_schedule(&host->finish_task);
+		}
+#if 0
+		else if (status & SD_STATUS_DD) {
+
+			/* Sometimes we get a DD before a NE in PIO mode */
+
+			if (!(host->flags & HOST_F_DMA) &&
+					(status & SD_STATUS_NE))
+				au1xmmc_receive_pio(host);
+			else {
+				au1xmmc_data_complete(host, status);
+				//tasklet_schedule(&host->data_task);
+			}
+		}
+#endif
+		else if (status & (SD_STATUS_CR)) {
+			if (host->status == HOST_S_CMD)
+				au1xmmc_cmd_complete(host,status);
+		}
+		else if (!(host->flags & HOST_F_DMA)) {
+			if ((host->flags & HOST_F_XMIT) &&
+			    (status & STATUS_DATA_OUT))
+				au1xmmc_send_pio(host);
+			else if ((host->flags & HOST_F_RECV) &&
+			    (status & STATUS_DATA_IN))
+				au1xmmc_receive_pio(host);
+		}
+		else if (status & 0x203FBC70) {
+			DBG("Unhandled status %8.8x\n", host->id, status);
+			handled = 0;
+		}
+
+		au_writel(status, HOST_STATUS(host));
+		au_sync();
+
+		ret |= handled;
+	}
+
+	enable_irq(AU1100_SD_IRQ);
+	return ret;
+}
+
+static void au1xmmc_poll_event(unsigned long arg)
+{
+	struct au1xmmc_host *host = (struct au1xmmc_host *) arg;
+
+	int card = au1xmmc_card_inserted(host);
+        int controller = (host->flags & HOST_F_ACTIVE) ? 1 : 0;
+
+	if (card != controller) {
+		host->flags &= ~HOST_F_ACTIVE;
+		if (card) host->flags |= HOST_F_ACTIVE;
+		mmc_detect_change(host->mmc, 0);
+	}
+
+	if (host->mrq != NULL) {
+		u32 status = au_readl(HOST_STATUS(host));
+		DBG("PENDING - %8.8x\n", host->id, status);
+	}
+
+	mod_timer(&host->timer, jiffies + AU1XMMC_DETECT_TIMEOUT);
+}
+
+static dbdev_tab_t au1xmmc_mem_dbdev =
+{
+	DSCR_CMD0_ALWAYS, DEV_FLAGS_ANYUSE, 0, 8, 0x00000000, 0, 0
+};
+
+static void au1xmmc_init_dma(struct au1xmmc_host *host)
+{
+
+	u32 rxchan, txchan;
+
+	int txid = au1xmmc_card_table[host->id].tx_devid;
+	int rxid = au1xmmc_card_table[host->id].rx_devid;
+
+	/* DSCR_CMD0_ALWAYS has a stride of 32 bits, we need a stride
+	   of 8 bits.  And since devices are shared, we need to create
+	   our own to avoid freaking out other devices
+	*/
+
+	int memid = au1xxx_ddma_add_device(&au1xmmc_mem_dbdev);
+
+	txchan = au1xxx_dbdma_chan_alloc(memid, txid,
+					 au1xmmc_dma_callback, (void *) host);
+
+	rxchan = au1xxx_dbdma_chan_alloc(rxid, memid,
+					 au1xmmc_dma_callback, (void *) host);
+
+	au1xxx_dbdma_set_devwidth(txchan, 8);
+	au1xxx_dbdma_set_devwidth(rxchan, 8);
+
+	au1xxx_dbdma_ring_alloc(txchan, AU1XMMC_DESCRIPTOR_COUNT);
+	au1xxx_dbdma_ring_alloc(rxchan, AU1XMMC_DESCRIPTOR_COUNT);
+
+	host->tx_chan = txchan;
+	host->rx_chan = rxchan;
+}
+
+static const struct mmc_host_ops au1xmmc_ops = {
+	.request	= au1xmmc_request,
+	.set_ios	= au1xmmc_set_ios,
+	.get_ro		= au1xmmc_card_readonly,
+};
+
+static int __devinit au1xmmc_probe(struct platform_device *pdev)
+{
+
+	int i, ret = 0;
+
+	/* THe interrupt is shared among all controllers */
+	ret = request_irq(AU1100_SD_IRQ, au1xmmc_irq, IRQF_DISABLED, "MMC", 0);
+
+	if (ret) {
+		printk(DRIVER_NAME "ERROR: Couldn't get int %d: %d\n",
+				AU1100_SD_IRQ, ret);
+		return -ENXIO;
+	}
+
+	disable_irq(AU1100_SD_IRQ);
+
+	for(i = 0; i < AU1XMMC_CONTROLLER_COUNT; i++) {
+		struct mmc_host *mmc = mmc_alloc_host(sizeof(struct au1xmmc_host), &pdev->dev);
+		struct au1xmmc_host *host = 0;
+
+		if (!mmc) {
+			printk(DRIVER_NAME "ERROR: no mem for host %d\n", i);
+			au1xmmc_hosts[i] = 0;
+			continue;
+		}
+
+		mmc->ops = &au1xmmc_ops;
+
+		mmc->f_min =   450000;
+		mmc->f_max = 24000000;
+
+		mmc->max_seg_size = AU1XMMC_DESCRIPTOR_SIZE;
+		mmc->max_phys_segs = AU1XMMC_DESCRIPTOR_COUNT;
+
+		mmc->max_blk_size = 2048;
+		mmc->max_blk_count = 512;
+
+		mmc->ocr_avail = AU1XMMC_OCR;
+
+		host = mmc_priv(mmc);
+		host->mmc = mmc;
+
+		host->id = i;
+		host->iobase = au1xmmc_card_table[host->id].iobase;
+		host->clock = 0;
+		host->power_mode = MMC_POWER_OFF;
+
+		host->flags = au1xmmc_card_inserted(host) ? HOST_F_ACTIVE : 0;
+		host->status = HOST_S_IDLE;
+
+		init_timer(&host->timer);
+
+		host->timer.function = au1xmmc_poll_event;
+		host->timer.data = (unsigned long) host;
+		host->timer.expires = jiffies + AU1XMMC_DETECT_TIMEOUT;
+
+		tasklet_init(&host->data_task, au1xmmc_tasklet_data,
+				(unsigned long) host);
+
+		tasklet_init(&host->finish_task, au1xmmc_tasklet_finish,
+				(unsigned long) host);
+
+		spin_lock_init(&host->lock);
+
+		if (dma != 0)
+			au1xmmc_init_dma(host);
+
+		au1xmmc_reset_controller(host);
+
+		mmc_add_host(mmc);
+		au1xmmc_hosts[i] = host;
+
+		add_timer(&host->timer);
+
+		printk(KERN_INFO DRIVER_NAME ": MMC Controller %d set up at %8.8X (mode=%s)\n",
+		       host->id, host->iobase, dma ? "dma" : "pio");
+	}
+
+	enable_irq(AU1100_SD_IRQ);
+
+	return 0;
+}
+
+static int __devexit au1xmmc_remove(struct platform_device *pdev)
+{
+
+	int i;
+
+	disable_irq(AU1100_SD_IRQ);
+
+	for(i = 0; i < AU1XMMC_CONTROLLER_COUNT; i++) {
+		struct au1xmmc_host *host = au1xmmc_hosts[i];
+		if (!host) continue;
+
+		tasklet_kill(&host->data_task);
+		tasklet_kill(&host->finish_task);
+
+		del_timer_sync(&host->timer);
+		au1xmmc_set_power(host, 0);
+
+		mmc_remove_host(host->mmc);
+
+		au1xxx_dbdma_chan_free(host->tx_chan);
+		au1xxx_dbdma_chan_free(host->rx_chan);
+
+		au_writel(0x0, HOST_ENABLE(host));
+		au_sync();
+	}
+
+	free_irq(AU1100_SD_IRQ, 0);
+	return 0;
+}
+
+static struct platform_driver au1xmmc_driver = {
+	.probe         = au1xmmc_probe,
+	.remove        = au1xmmc_remove,
+	.suspend       = NULL,
+	.resume        = NULL,
+	.driver        = {
+		.name  = DRIVER_NAME,
+	},
+};
+
+static int __init au1xmmc_init(void)
+{
+	return platform_driver_register(&au1xmmc_driver);
+}
+
+static void __exit au1xmmc_exit(void)
+{
+	platform_driver_unregister(&au1xmmc_driver);
+}
+
+module_init(au1xmmc_init);
+module_exit(au1xmmc_exit);
+
+#ifdef MODULE
+MODULE_AUTHOR("Advanced Micro Devices, Inc");
+MODULE_DESCRIPTION("MMC/SD driver for the Alchemy Au1XXX");
+MODULE_LICENSE("GPL");
+#endif
+